EN 6059-308-2014 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 308 Rapid change of temperature《航空航天系列 电缆 安装 芳纶纤维保护套 第308部分 温度的急剧变化.pdf

1、BSI Standards PublicationBS EN 6059-308:2014Aerospace series Electricalcables, installation Protection sleeves TestmethodsPart 308: Rapid change of temperatureBS EN 6059-308:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 6059-308:2014.The UK participation

2、in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract

3、. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 84535 2ICS 49.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

4、 theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS EN 6059-308:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-308 December 2014 ICS 49.060 English Version Aerospace series - Electrical cables, installation - Protecti

5、on sleeves - Test methods - Part 308: Rapid change of temperatureSrie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 308: Variation rapide de temprature Luft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche - Prfverfahren - Teil 30

6、8: Schneller Temperaturwechsel This European Standard was approved by CEN on 4 January 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date

7、 lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation u

8、nder the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme

9、r Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT E

10、UROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-308:2014 EBS EN 6059-308:2014EN 6059-308:2014 (E) 2 C

11、ontents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Preparation of specimens .4 4 Apparatus .5 5 Method 6 6 Requirements .6 BS EN 6059-308:2014EN 6059-308:2014 (E) 3 Foreword This document (EN 6059-308:2014) has been prepared by the Aerospace and Defence Industries Association of Europe - S

12、tandardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard s

13、hall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at the latest by June 2015. Attention is drawn to the possibility that some of the elements of this documen

14、t may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus

15、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed

16、en, Switzerland, Turkey and the United Kingdom. BS EN 6059-308:2014EN 6059-308:2014 (E) 4 1 Scope This European Standard specifies a method of assessing the behaviour of conductive protection sleeves or conduits after exposure to a rapid change of temperature. It shall be used together with EN 6059-

17、100. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

18、amendments) applies. EN 3475-301, Aerospace series Cables, electrical, aircraft use Test methods Part 301: Ohmic resistance per unit length EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General 3 Preparation of specimens Each sleeve or condui

19、t specimen shall have a length of 600 mm minimum, and shall be prepared according to Figure 1. The cable bundle shall be made of standard aerospace cables, according to Figure 1. The diameter of the bundle shall be the maximum diameter applicable to the used sleeve or conduit. Then apply a twisting

20、with the number of twists per metre, as specified in the product standard. The cable bundle and the twisted sleeve shall be tied using standard aerospace tying devices compliant with the temperature range. The tying devices on the cable bundle shall be installed with a pitch of 300 mm. The tying dev

21、ices on the sleeve shall be installed with a pitch of 100 mm. Measure the ohmic resistance of each specimen according to EN 3475-301, tests shall be carried out at ambient temperature Ta (typically 20 C). BS EN 6059-308:2014EN 6059-308:2014 (E) 5 Dimensions in millimetres Key 1 Tying device 2 Cable

22、bundle 3 Sleeve 4 Bundle at the maximum allowed diameter of the sleeve Figure 1 Specimen configuration 4 Apparatus Two chambers, one for low temperature and one for high temperature, shall be provided. The chambers shall be located that the time of transfer (t2) of the specimen from one chamber to t

23、he other shall be less than 1 min. The chambers shall be capable of maintaining the specified temperatures (TA andTB) to 3 % at those locations where the specimens are installed. The volume of the chambers shall be such that after insertion of the specimens, the temperature shall be within the speci

24、fied tolerances after a time of not more than 5 min or 10 % of the exposure time, whichever is the smallest. Unless otherwise specified, the thermal conduction of the mounting shall be sufficiently low, so that the specimens may be considered thermally isolated. BS EN 6059-308:2014EN 6059-308:2014 (

25、E) 6 5 Method The specimen shall be installed in an oven and subjected to a temperature cycling defined in Figure 2. The number of cycles shall be 10. Keys 1 Time t min. 2 1 cycle A: start of the first cycle t1= 30 t2 1 min. B: end of first cycle Figure 2 Temperature cycle 6 Requirements The pass/fa

26、il requirements shall be specified in the product standard. This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other stand

27、ardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into

28、standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can

29、 provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and ado

30、pted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscriptio

31、n services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is r

32、efreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscr

33、ibing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications

34、 on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We

35、continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and o

36、ther BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under th

37、e Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensin

38、g Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW