EN 6059-503-2017 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 503 Temperature rise due to rated current injected on the sleeve.pdf

1、Aerospace series - Electrical cables, installation - Protection sleeves - Test methodsPart 503: Temperature rise due to rated current injected on the sleeveBS EN 6059503:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

2、NORM EN 6059-503 August 2017 ICS 49.060 Supersedes EN 6059-503:2012English Version Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 503: Temperature rise due to rated current injected on the sleeve Srie arospatiale - Cbles lectriques, installation - Gaine

3、s de protection - Mthodes dessais - Partie 503 : chauffement sous courant nominal Luft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche - Prfverfahren - Teil 503: Erwrmung bei Nennstrom des SchutzschlauchsThis European Standard was approved by CEN on 12 June 2017. CEN members ar

4、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

5、the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Ce

6、ntre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithua

7、nia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix

8、 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-503:2017 ENational forewordThis British Standard is the UK implementation of EN 6059503:2017. It supersedes BS EN 6059503:2012, which is withdrawn.The U

9、K participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary prov

10、isions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 97969 9ICS 49.060Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published

11、under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 6059503:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-503 August 2017 ICS 49.060 Supersedes EN 6059-503:2012Engli

12、sh Version Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 503: Temperature rise due to rated current injected on the sleeve Srie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 503 : chauffement sous couran

13、t nominal Luft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche - Prfverfahren - Teil 503: Erwrmung bei Nennstrom des SchutzschlauchsThis European Standard was approved by CEN on 12 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

14、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European St

15、andard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the n

16、ational standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

17、Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and

18、 by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-503:2017 EBS EN 6059503:2017EN 6059-503:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Preparation of specimens 4 4 Method 7 5 Requirements . 8 BS EN 6059503:2017EN 6059-503:2017 (E) 3 Euro

19、pean foreword This document (EN 6059-503:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the

20、 National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2018, and conflicting na

21、tional standards shall be withdrawn at the latest by February 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 6059-

22、503:2012. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, F

23、rance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6059503:2017EN 6059-503:2017 (E) 4 1 Scope This European Standa

24、rd specifies a method of assessing the behaviour and temperature increase of EMI protection sleeves or conduits when subject to permanent and/or fault currents in the shielding of the conduit or sleeve material and their effect on the cables within the cable sleeve. It shall be used together with EN

25、 3475-100. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

26、g any amendments) applies. EN 3475-100, Aerospace series - Cables, electrical, aircraft use - Test methods - Part 100: General 3 Preparation of specimens 3.1 General Each specimen having 750 mm to 1 000 mm useful length between the supports, shall be installed horizontally in front of a screen and l

27、ightly stretched at the ends to avoid any slack during the test. The test shall be carried out at ambient temperature Ta(typically 20 C) in a chamber where the whole unit shall be sheltered from draughts. An extraction shall be provided but only operated after completion of the test. To identify the

28、 appearance of smoke, a screen with black and white horizontal bands or any other device shall be used. 3.2 Preparation of specimens Specimens will be installed horizontally in a box with a background striped in white and black. To detect smoke appearance the box will be transparent in the front. It

29、 will be closed to avoid any heat exchange. An exhaust fan will be added above the box in case of toxic fume generation (it shall not function during the test but only at the end and this to not disrupts the heating). As described below two (2) circuits are provided: the first one is for the connect

30、ing power and the second one is for the measurement. BS EN 6059503:2017EN 6059-503:2017 (E) 5 3.3 Connecting system 3.3.1 General To ensure that the contacts bringing the current consider all the strands of the shielding, the following mounting is to be assured: A split ring will be placed between t

31、he bundle ant the sleeve. A CuNi flat braid of a section of 3,44 mm2will be connected to the sleeve with a metallic clamp. Terminal lugs will be fixed at the flat braid extremities. 3.3.2 First case (Figure 1) This proposition considers specimens without connectors at the ends. Key 1 sleeve 2 cable

32、bundle 3 band-it 4 split ring 5 flat braid 6 terminal lug 7 measurement branch 8 power branch Figure 1 BS EN 6059503:2017EN 6059-503:2017 (E) 6 3.3.3 Second case (Figure 2) This proposition considers specimens with connectors at the ends. Connectors are placed at the specimens extremities. Copper po

33、wer bars are added. Key 1 cable bundle 2 band-it 3 connector (backshell-plug/receptable) 4 split ring 5 sleeve 6 flat braid 7 screw/nut 8 measurement branch 9 copper power bars Figure 2 BS EN 6059503:2017EN 6059-503:2017 (E) 7 4 Method The purpose of this test shall be to check that there is no smok

34、e emission excessive increase of temperature for the nominal current, bringing the conductor to a temperature RT, and that for an overload current bringing the conductor to a temperature (Max RT + 5 C or Max RT + 10 C) there is neither ignition nor disappearance of non conductive materials. The test

35、 shall be performed with a current generator in DC or AC (400 Hz to 800 Hz RMS). The test shall be performed on sizes as defined in the concerned specification or product standard. The temperatures shall be determined by measuring the variation of the voltage drop in the central part of the cable (2

36、/3 of the useful length maximum) between the voltage application points. ( )20 201 0,004 20URUR=+when Ta= 20 C The current injection shall respect the curve shown in Figure 3. Figure 3 A = current C = temperature RT = room temperature T0to T0= time to stabilization of temperature under initial curre

37、nt T1= T0+ 1 min T2= T1+ 200 ms T3= T2+ 500 ms T4= T3+ 200 ms T4to T5= time to decrease temperature at least to reach RT + 5 C, if this value have been pass, if not during 1 min BS EN 6059503:2017EN 6059-503:2017 (E) 8 5 Requirements The temperature shall be in accordance with the curve shown in Fig

38、ure 3. At In: no visible smoke or smell or appreciable change of colour (see Note); T shall be inferior to the value specified in product standard. At I1: no visible deterioration of materials (peeling, cracking) no spontaneous combustion and no visible smoke; T1shall be inferior to the value specif

39、ied in product standard. NOTE “Appreciable colour change” is to be defined as the original colour is still recognizable. BS EN 6059503:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and s

40、ervices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience a

41、nd expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information

42、on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, includi

43、ng British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI pu

44、blicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commerci

45、al publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior w

46、ritten consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole

47、named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further

48、 reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor

49、permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily