EN 607-2004 en Eaves Gutters and Fittings Made of PVC-U - Definitions Requirements and Testing《未增塑聚氯乙烯制屋檐沟和附件 定义 要求和检验》.pdf

1、BRITISH STANDARDBS EN 607:2004Eaves gutters and fittings made of PVC-U Definitions, requirements and testingThe European Standard EN 607:2004 has the status of a British StandardICS 01.040.91; 91.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g

2、40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 607:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 September 2005 BSI 26 September 2005ISBN 0 580 46125 4National forewordThis

3、 British Standard is the official English language version of EN 607:2004. It supersedes BS EN 607:1996. Together with BS EN 12200-1:2000 and BS EN 1462:2005 it will replace BS 4576-1:1989 which is scheduled for withdrawal in September 2007.The UK participation in its preparation was entrusted by Te

4、chnical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping systems for non-pressure applications, which has the responsibility to:A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standar

5、ds which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This pu

6、blication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internati

7、onal/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page,

8、 pages 2 to 20, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 607 November 2004 ICS 01.040.91; 91.060.

9、20 Supersedes EN 607:1995 English version Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing Gouttires pendantes et leurs raccords en PVC-U - Dfinitions, exigences et mthodes dessai Hngedachrinnen und Zubehrteile aus PVC-U - Begriffe, Anforderungen und Prfung This Europ

10、ean Standard was approved by CEN on 15 July 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conce

11、rning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

12、language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour

13、g, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of explo

14、itation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 607:2004: EEN 607:2004 (E) 2 Contents page Foreword4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 3.1 eaves gutter6 3.2 down-pipe.6 3.3 union-clip (gutter-union) .6 3.4 joint bracket (union

15、-bracket) 6 3.5 gutter adaptor.6 3.6 angle6 3.7 stop end 6 3.8 outlet .6 3.9 commercial length .6 4 Material .7 4.1 Raw material.7 4.2 Utilisation of non virgin material7 5 General characteristics of profiles - Appearance.7 6 Geometrical characteristics of profiles .7 6.1 Width .7 6.2 Length .7 7 Ph

16、ysical and mechanical characteristics of profiles .7 8 General characteristics of fittings8 8.1 General8 8.2 Appearance 8 8.3 Shape and dimensions8 9 Physical characteristics of fittings 9 10 Gutter sealing rings.9 11 Solvent cements 9 12 Designation 10 13 Marking .10 14 Fitness for purpose of gutte

17、r systems 11 15 Production control.11 Annex A (normative) Utilisation of non-virgin material12 A.1 Material definitions 12 A.1.1 virgin material 12 A.1.2 own reprocessable material .12 A.1.3 external reprocessable material.12 A.1.4 recyclable material.12 A.2 Reprocessable and recyclable material 12

18、A.2.1 Own reprocessable material.12 A.2.2 External reprocessable and recyclable materials with agreed specification13 A.2.3 External reprocessable and recyclable material not covered by an agreed specification 15 Annex B (normative) Impact test 16 EN 607:2004 (E) 3 Annex C (normative) Heat reversion

19、 test for fittings .17 Annex D (normative) Watertightness test .18 Annex E (informative) Cross section areas.19 Bibliography20 EN 607:2004 (E) 4 Foreword This document (EN 607:2004) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for

20、wall cladding”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by May 2005.

21、This document supersedes EN 607:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar

22、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 607:2004 (E) 5 1 Scope This document specifies requirements and test methods of eaves gutters and fittings made from unplasti

23、cized poly(vinyl chloride) (PVC-U), and intended to be used for rainwater drainage. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of th

24、e referenced document (including any amendments) applies. EN 513 Unplasticized polyvinyl chloride (PVC-U) profiles for the fabrication of windows and doors Determination of the resistance to artificial weathering EN 638 Plastics piping and ducting systems Thermoplastics pipes Determination of tensil

25、e properties EN 681-1 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber EN 681-2 Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomer

26、s EN 681-3 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber EN 681-4 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyureth

27、ane sealing elements EN 727 Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening temperature (VST) EN 743 Plastics piping and ducting systems Thermoplastics pipes Determination of the longitudinal reversion EN 763 Plastics piping and ducting systems

28、- Injection-moulded thermoplastics fittings - Test method for visually assessing effects of heating EN 922 Plastics piping and ducting systems Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) Specimen preparation for determination of the viscosity number and calculation of the K-valu

29、e EN 1905 Plastics piping systems Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material Method for assessment of the PVC content based on total chlorine content EN 10204:1991 Metallic products Types of inspection documents EN 20105-A02 Textiles - Tests for colour fastness Part A02:

30、 Grey scale for assessing change in colour (ISO 105-A02:1993) EN ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994) EN ISO 1183-3 Plastics - Methods for determining the density of non-cellular

31、plastics - Gas pyknometer method (ISO 1183-3:1999) EN 607:2004 (E) 6 EN ISO 4892-2 Plastics Methods of exposure to laboratory light sources Part 2: Xenon arc sources (ISO 4892-2:1994) EN ISO 4892-3 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps (ISO 4892-3:1994

32、) EN ISO 8256 Plastics - Determination of tensile-impact strength (ISO 8256:1990, including Technical Corrigendum 1:1991) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 eaves gutter gutter situated outside the building and supported by brack

33、ets 3.2 down-pipe pipe fitted to a gutter to lead rainwater from the gutter to the drainage system or sewer 3.3 union-clip (gutter-union) fitting for joining two gutters and supported only by those gutters 3.4 joint bracket (union-bracket) fitting for joining two gutters which is supported by the bu

34、ilding structure 3.5 gutter adaptor fitting for joining two different shaped gutters 3.6 angle fitting for joining two gutters installed in two different directions 3.7 stop end fitting for stopping the flow, fixed at the end of a gutter or an outlet 3.8 outlet fitting for draining off the rainwater

35、 from the gutter into the down-pipe 3.9 commercial length length of a gutter or a down-pipe which was produced in a factory EN 607:2004 (E) 7 4 Material 4.1 Raw material The raw material shall be PVC-U to which are added those additives that are needed to facilitate the manufacture of components con

36、forming to the requirements of this document. When calculated on the basis of a known formulation or in case of dispute or not known formulation, determined in accordance with EN 1905 the PVC content shall be at least 80 % by mass for profiles and 85 % by mass for injection-moulded fittings. 4.2 Uti

37、lisation of non virgin material Requirements for the utilisation of non-virgin materials are given in Annex A (normative). 5 General characteristics of profiles - Appearance When viewed without magnification the internal and external surfaces of gutters shall be smooth, clean and free from scoring,

38、cavities, and other surface defects. The ends of gutters shall be cut cleanly and square to the axis of the profile. 6 Geometrical characteristics of profiles 6.1 Width Gutters shall be designated by their upper opening width (size) (See examples of cross section areas in Annex E). The manufacturer

39、shall declare the usable area of the cross-section of the gutter at its designed top opening width for the calculation of flow capacity. This usable area shall be either marked on the gutter or given in commercial documents. 6.2 Length The commercial length of a gutter shall have a positive toleranc

40、e when measured at 20 C. 7 Physical and mechanical characteristics of profiles The requirements for the physical and mechanical characteristics and the conditions for the respective test methods shall conform to those given in Table 1. NOTE Any conflicting parameters and requirements given in the te

41、st method standards referred to do not apply here. EN 607:2004 (E) 8 Table 1 Physical and mechanical characteristics of profiles Characteristics Requirement Test parameters Test method Hammer impact strength (type test) No break or crack visible without magnification Temperature (0 2) C Annex B Spee

42、d 5 mm/min Tensile strength (type test) 42 N/mm Specimen type type 2, 3 or 5 aconforming to EN ISO 527-2 EN 638 Speed 5 mm/min Elongation at break (type test) 100 % Specimen type type 2, 3 or 5 aconforming to EN ISO 527-2 EN 638 Specimen type type 2, 3 or 5 aconforming to EN ISO 8256 Tensile impact

43、strength (type test) 500 kJ/m Temperature (23 2) C EN ISO 8256 Test temperature (100 2) C Heat reversion (type and production control test) 3 % Time (30 2) min EN 743 Vicat softening temperature (type test) 75 C Conforming to EN 727 EN 727 aIn case of dispute, test specimen 5 shall be used. 8 Genera

44、l characteristics of fittings 8.1 General The following types of fittings shall conform to the requirements given in 8.2, 8.3 and Clause 8: union clip, joint-bracket, gutter adaptor, angle, stop-end, outlet and expansion piece. 8.2 Appearance When viewed without magnification the internal and extern

45、al surfaces of fittings shall be smooth, clean and free from scoring, cavities, and other surface defects. 8.3 Shape and dimensions The fittings shall be compatible with the shape and the dimensions of the profile or the gutter. The outlets shall be compatible with down-pipes and fittings. EN 607:20

46、04 (E) 9 9 Physical characteristics of fittings The requirements for the physical characteristics and the conditions for the respective test methods shall conform to those given in Table 2. NOTE Any conflicting parameters and requirements given in the test method standards referred to do not apply.

47、Table 2 Physical characteristics of fittings Characteristics Requirement Test parameters Test method Temperature (150 2) C Effect of heating a(production control test) cand dTime (15 2) min. Method A of EN 763 in air Temperature (65 2) C Heat reversion b(type test) No visible deformation without mag

48、nification Time (30 2) min. Annex C Vicat softening temperature (type test) 75 C Conforming to EN 727 EN 727 a Without seal and only for injection-moulded fittings. b For fittings produced by processes other than injection moulding. c1) Within a radius of 15 times the wall thickness around the injec

49、tion point, the depth of cracks, delamination or blisters shall not exceed 50 % of the wall thickness at that point. 2) Within a distance of 10 times the wall thickness from the diaphragm zone, the depth of cracks, delamination or blisters shall not exceed 50 % of the wall thickness at that point. 3) Within a distance of 10 times the wall thickness from the ring gate, the length of cracks shall not exceed 50 % of the wall thickness at that point. 4) The weld line shall not have opened more th