EN 6075-2017 en Aerospace series - Static seal elements O-Ring ethylenepropylene moulded phosphate ester resistant (- 55 to 107 - Inch series《航空航天系列-静态密封O环乙烯基丙烯铸造抗磷酸盐酯(-55℃到107℃)-英.pdf

1、Aerospace series - Static seal elements O-Ring ethylene-propylene, moulded, phosphate ester resistant (- 55 C to 107 C) - Inch seriesBS EN 6075:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6075 May 2017 ICS

2、49.035 English Version Aerospace series - Static seal elements O-Ring ethylene-propylene, moulded, phosphate ester resistant (- 55 C to 107 C) - Inch series Srie arospatiale - Joint torique statique thylne-propylne, moul, rsistant lester phosphorique (- 55 C 107 C) - Srie en inches Luft- und Raumfah

3、rt - Statische Dichtungen O-Ringe Ethylen-Propylen, geformt, bestndig gegen Phosphorsureester (- 55 C bis 107 C) - Inch Reihe This European Standard was approved by CEN on 4 December 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for gi

4、ving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three of

5、ficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

6、of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Sloveni

7、a, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved wo

8、rldwide for CEN national Members. Ref. No. EN 6075:2017 ENational forewordThis British Standard is the UK implementation of EN 6075:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components.A list of organizations rep

9、resented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0

10、580 95514 3ICS 49.035Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affected BRITISH ST

11、ANDARDBS EN 6075:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6075 May 2017 ICS 49.035 English Version Aerospace series - Static seal elements O-Ring ethylene-propylene, moulded, phosphate ester resistant (- 55 C to 107 C) - Inch series Srie arospatiale - Joint torique statique thylne-pr

12、opylne, moul, rsistant lester phosphorique (- 55 C 107 C) - Srie en inches Luft- und Raumfahrt - Statische Dichtungen O-Ringe Ethylen-Propylen, geformt, bestndig gegen Phosphorsureester (- 55 C bis 107 C) - Inch Reihe This European Standard was approved by CEN on 4 December 2016. CEN members are bou

13、nd to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the C

14、EN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre

15、has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

16、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17,

17、B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6075:2017 EBS EN 6075:2017EN 6075:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements 4 4 Designation 15 5 Markin

18、g and packaging . 15 6 Technical specification 15 7 Quality assurance 15 (informative) Standard evolution form . 16 BS EN 6075:2017EN 6075:2017 (E) 3 European foreword This document (EN 6075:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-

19、STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the st

20、atus of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2017, and conflicting national standards shall be withdrawn at the latest by November 2017. Attention is drawn to the possibility that some of the elements of this document may be the

21、 subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cr

22、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

23、rkey and the United Kingdom. BS EN 6075:2017EN 6075:2017 (E) 4 1 Scope This European Standard specifies the characteristics of configuration, dimensions, tolerances and mass for moulded O-Ring seal elements, phosphate ester fluid resistant, for use as static seals in hydraulic systems for aerospace

24、application. Application temperature range: 55 C to 107 C of continuous operation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For und

25、ated references, the latest edition of the referenced document (including any amendments) applies. EN 6109, Aerospace series Static seal elements elastomer moulded, phosphate ester resistant Technical specification1)EN 6111, Aerospace series Ethylene-propylene elastomer (EPM/EPDM) Hardness 80 IRHD f

26、or static seal elements in hydraulic systems for long-term application Material standard1)EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts 3 Requirements 3.1 Configuration, dimensions, tolerances and mass Configuration shall be in accordance w

27、ith Figure 1; Dimensions shall conform with Figure 1 and Table 1; Tolerances shall be in accordance with Table 1; Mass shall be in accordance with Table 1. Dimensions and tolerances are expressed in millimetres (inches). 1)Published as ASD-STAN Prestandard at the date of publication of this standard

28、. http:/www.asd-stan.org/ BS EN 6075:2017EN 6075:2017 (E) 5 3.2 Material Ethylene-propylene elastomer (EPM/EPDM) per EN 6111. Figure 1 Configuration BS EN 6075:2017EN 6075:2017 (E) 6 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (1 of 9) Diameter code nullW nullID Mass kg/1000 piece

29、s Tolerances Tolerances null10 % 001 1,02 (.040) null0,08 (null.003) 0,74 (.029) null0,10 (null.004) 0,006 002 1,27 (.050) 1,07 (.042) 0,012 003 1,52 (.060) 1,42 (.056) 0,019 004 1,78 (.070) 1,78 (.070) 0,033 005 2,57 (.101) null0,13 (null.005) 0,040 006 2,90 (.114) 0,042 007 3,68 (.145) 0,051 008 4

30、,47 (.176) 0,058 009 5,28 (.208) 0,066 010 6,07 (.239) 0,072 011 7,65 (.301) 0,087 012 9,25 (.364) 0,100 013 10,82 (.426) 0,115 014 12,42 (.489) 0,131 015 14,00 (.551) 0,145 016 15,60 (.614) 0,160 017 17,17 (.676) 0,173 018 18,77 (.739) 0,190 019 20,35 (.801) null0,15 (null.006) 0,202 020 21,95 (.86

31、4) 0,218 021 23,52 (.926) 0,232 022 25,12 (.989) 0,247 023 26,70 (1.051) 0,263 024 28,30 (1.114) 0,275 025 29,87 (1.176) 0,291 026 31,47 (1.239) 0,305 027 33,05 (1.301) 0,320 028 34,65 (1.364) 0,333 029 37,82 (1.489) null0,25 (null.010) 0,363 030 40,10 (1.614) 0,393 031 44,17 (1.739) 0,423 032 47,35

32、 (1.864) 0,458 033 50,52 (1.989) 0,480 034 53,70 (2.114) 0,510 035 56,87 (2.239) 0,538 036 60,05 (2.364) 0,567 037 63,22 (2.489) 0,596 038 66,40 (2.614) 0,627 BS EN 6075:2017EN 6075:2017 (E) 7 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (2 of 9) Diameter code nullW nullID Mass kg/

33、1000 pieces Tolerances Tolerances null10 % 039 1,78 (.070) null0,08 (null.003) 69,57 (2.739) null0,38 (null.015) 0,656 040 72,75 (2.864) 0,685 041 75,92 (2.989) 0,713 042 82,27 (3.239) 0,771 043 88,62 (3.489) 0,830 044 94,97 (3.739) 0,889 045 101,32 (3.989) 0,948 046 107,67 (4.239) 1,005 047 114,02

34、(4.489) 1,063 048 120,37 (4.739) 1,121 049 126,72 (4.989) null0,58 (null.023) 1,181 050 133,07 (5.239) 1,238 102 2,62 (.103) null0,08 (null.003) 1,24 (.049) null0,13 (null.005) 0,078 103 2,06 (.081) 0,093 104 2,84 (.112) 0,108 105 3,63 (.143) 0,124 106 4,42 (.174) 0,141 107 5,23 (.206) 0,157 108 6,0

35、2 (.237) 0,172 109 7,59 (.299) 0,202 110 9,19 (.362) 0,235 111 11,53 (.424) 0,266 112 12,37 (.487) 0,297 113 13,94 (.549) 0,330 114 15,54 (.612) 0,360 115 17,12 (.674) 0,392 116 18,72 (.737) 0,425 117 20,29 (.799) null0,15 (null.006) 0,456 118 21,89 (.862) 0,489 119 23,47 (.924) 0,519 120 25,07 (.98

36、7) 0,550 121 26,64 (1.049) 0,583 122 28,24 (1.112) 0,613 123 29,82 (1.174) 0,644 124 31,42 (1.237) 0,677 125 32,99 (1.299) 0,707 126 34,59 (1.362) 0,739 127 36,17 (1.424) 0,771 128 37,77 (1.487) 0,803 BS EN 6075:2017EN 6075:2017 (E) 8 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (3

37、 of 9) Diameter code nullW nullID Mass kg/1000 pieces Tolerances Tolerances null10 % 129 2,62 (.103) null0,08 (null.003) 39,34 (1.549) null0,25 (null.010) 0,833 130 40,94 (1.612) 0,866 131 42,52 (1.674) 0,897 132 44,12 (1.737) 0,930 133 45,69 (1.799) 0,961 134 47,29 (1.862) 0,991 135 48,90 (1.925) 1

38、,024 136 50,47 (1.987) 1,055 137 52,07 (2.050) 1,088 138 53,64 (2.112) 1,118 139 55,25 (2.175) 1,150 140 56,82 (2.237) 1,183 141 58,42 (2.300) 1,214 142 59,99 (2.362) 1,244 143 61,60 (2.425) 1,277 144 63,17 (2.487) 1,308 145 64,77 (2.550) 1,338 146 66,34 (2.612) 1,371 147 67,95 (2.675) null0,38 (nul

39、l.015) 1,402 148 69,52 (2.737) 1,434 149 71,12 (2.800) 1,466 150 72,69 (2.862) 1,497 151 75,87 (2.987) 1,561 152 82,22 (3.237) 1,686 153 88,57 (3.487) 1,813 154 94,92 (3.737) 1,939 155 101,27 (3.987) 2,066 156 107,62 (4.237) 2,192 157 113,97 (4.487) 2,319 158 120,32 (4.737) 2,444 159 126,67 (4.987)

40、2,577 160 133,02 (5.237) null0,58 (null.023) 2,697 161 139,37 (5.487) 2,822 162 145,72 (5.737) 2,950 163 152,07 (5.987) 3,075 164 158,42 (6.237) 3,202 165 164,77 (6.487) 3,328 166 171,12 (6.737) 3,453 167 177,47 (6.987) 3,580 BS EN 6075:2017EN 6075:2017 (E) 9 Table 1 O-Rings Diameter code, dimension

41、s, tolerances and mass (4 of 9) Diameter code nullW nullID Mass kg/1000 pieces Tolerances Tolerances null10 % 168 2,62 (.103) null0,08 (null.003) 183,82 (7.237) null0,76 (null.030) 3,706 169 190,17 (7.487) 3,833 170 196,52 (7.737) 3,966 171 202,87 (7.987) 4,086 172 209,22 (8.237) 4,211 173 215,57 (8

42、.487) 4,338 174 221,92 (8.737) 4,464 175 228,27 (8.987) 4,589 176 234,62 (9.237) 4,717 177 240,97 (9.487) 4,849 178 247,32 (9.737) 4,969 201 3,53 (.139) null0,10 (null.004) 4,34 (.171) null0,13 (null.005) 0,286 202 5,94 (.234) 0,344 203 7,52 (.296) 0,399 204 9,12 (.359) 0,457 205 10,69 (.421) 0,516

43、206 12,29 (.484) 0,573 207 13,87 (.546) 0,631 208 15,47 (.609) 0,689 209 17,04 (.671) 0,745 210 18,64 (.734) null0,15 (null.006) 0,803 211 20,22 (.796) 0,861 212 21,82 (.859) 0,918 213 23,39 (.921) 0,975 214 24,99 (.984) 1,032 215 26,57 (1.046) 1,090 216 28,17 (1.109) 1,148 217 29,74 (1.171) 1,205 2

44、18 31,34 (1.234) 1,263 219 32,92 (1.296) 1,320 220 34,52 (1.359) 1,377 221 36,09 (1.421) 1,435 222 37,69 (1.484) 1,493 223 40,87 (1.609) null0,25 (null.010) 1,607 224 44,04 (1.734) 1,722 225 47,22 (1.859) 1,836 226 50,39 (1.984) 1,952 227 53,57 (2.109) 2,068 228 56,74 (2.234) 2,181 229 59,92 (2.359)

45、 2,298 BS EN 6075:2017EN 6075:2017 (E) 10 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (5 of 9) Diameter code nullW nullID Mass kg/1000 pieces Tolerances Tolerances null10 % 230 3,53 (.139) null0,10 (null.004) 63,09 (2.484) 2,411 231 66,27 (2.609) 2,527 232 69,44 (2.734) null0,38 (

46、null.015) 2,643 233 72,62 (2.859) 2,757 234 75,79 (2.984) 2,872 235 78,97 (3.109) 2,986 236 82,14 (3.234) 3,102 237 85,32 (3.359) 3,217 238 88,49 (3.484) 3,331 239 91,67 (3.609) 3,447 240 94,84 (3.734) 3,561 241 98,02 (3.859) 3,676 242 101,19 (3.984) 3,793 243 104,37 (4.109) 3,906 244 107,54 (4.234)

47、 4,022 245 110,72 (4.359) 4,135 246 113,89 (4.484) 4,252 247 117,07 (4.609) 4,365 248 120,24 (4.734) 4,481 249 123,42 (4.859) 4,597 250 126,59 (4.984) 4,711 251 129,77 (5.109) null0,58 (null.023) 4,826 252 132,94 (5.234) 4,941 253 136,12 (5.359) 5,056 254 139,29 (5.484) 5,171 255 142,47 (5.609) 5,28

48、5 256 145,64 (5.734) 5,401 257 148,82 (5.859) 5,515 258 151,99 (5.984) 5,630 259 158,34 (6.234) 5,860 260 164,69 (6.484) 6,097 261 171,04 (6.734) 6,321 262 177,39 (6.984) 6,551 263 183,74 (7.234) null0,76 (null.030) 6,780 264 190,09 (7.484) 7,010 265 196,44 (7.734) 7,240 266 202,79 (7.984) 7,469 267

49、 209,14 (8.234) 7,701 268 215,49 (8.484) 7,931 269 221,84 (8.734) 8,160 BS EN 6075:2017EN 6075:2017 (E) 11 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (6 of 9) Diameter code nullW nullID Mass kg/1000 pieces Tolerances Tolerances null10 % 270 3,53 (.139) null0,10 (null.004) 228,19 (8.984) null0,76 (null.030) 8,390 271 234,54 (9.234) 8,619 272 240,89 (9.484) 8,850 273 247,24 (9.734) 9,086 274 253,59 (9.984) 9,309 275 266,29 (10.484) 9,768 276 278,99 (10.984) 10,23