EN 6138-2017 en Aerospace series - Cap protective non-metallic for fitting ends 3 000 PSI hydraulic systems《航空航天系列-防护端部非金属保护用帽-3000PSI液压系统》.pdf

1、BS EN 6138:2017Aerospace series Cap, protective, non-metallic for fitting ends 3 000 PSI hydraulic systemsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 6138:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 6138:2017.

2、The UK participation in its preparation was entrusted to TechnicalCommittee ACE/69, Aerospace hydraulic systems, fluids and components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary prov

3、isions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 95837 3 ICS 49.080 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was publishe

4、d under the authority of the Standards Policy and Strategy Committee on 30 April 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 6138:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6138 March 2017 ICS 49.080 English Version Aerospace series - Cap, prote

5、ctive, non-metallic for fitting ends 3 000 PSI hydraulic systems Srie arospatiale - Chapeau, protecteur, non mtallique pour raccord 3 000 PSI circuits hydrauliques Luft- und Raumfahrt - Kappe, nicht metallisch zum Schutz fr Endfittinge 3 000 PSI Hydraulik SystemeThis European Standard was approved b

6、y CEN on 2 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand

7、ards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and no

8、tified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,

9、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-C

10、ENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6138:2017 EBS EN 6138:2017EN 6138:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Re

11、quirements . 5 4 Technical requirement . 6 5 Designation . 7 6 Marking . 7 7 Packaging . 7 8 Example of installation . 7 9 Technical specification . 8 BS EN 6138:2017EN 6138:2017 (E) 3 European foreword This document (EN 6138:2017) has been prepared by the Aerospace and Defence Industries Associatio

12、n of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This Euro

13、pean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the

14、 elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta

15、ndard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slo

16、venia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6138:2017EN 6138:2017 (E) 4 1 Scope This European Standard specifies the dimensions, tolerances and required characteristics of protective caps to seal fluid ports during transportation and storage in order to prevent: contamina

17、tion by moisture, fluids, chemicals and particles; spillage inside package or aircraft section; port and pipe end damages; port and pipe clogging due to plug ingestion. Because of the cleanliness requirements, parts shall only be used once. 2 Normative references The following documents, in whole or

18、 in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerosp

19、ace products EN 6079, Aerospace series Pipe coupling 24 cone Female fitting ends, flareless type Inch series1)EN 6102, Aerospace series Fluid-hydraulic, phosphate ester-base, fire resistant Technical specification1)EN 9100, Quality Management Systems Requirements for Aviation, Space and Defence Orga

20、nizations ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 3161, Aerospace UNJ threads General requirements and limit dimensions SAE-AS4059, Aerospace Fluid Power Contamination Classification for Hydraulic Fluids2)SAE-AS

21、4375, Fitting End, Flareless, Design Standard2)SAE-AS4395, Fitting End, Flared, Tube Connection, Design Standard2)SAE-AS33514, Fitting End, Standard Dimensions for Flareless Tube Connection and Gasket Seal2)FED-STD-595C, Colors used in government procurement 1)In preparation at the date of publicati

22、on of this European Standard. NOTE Until publication of EN 6079 use SAE-AS4375 and until publication of EN 6102 use AS1241. 2)Published by: SAE National (US) Society of Automotive Engineers. http:/www.sae.org/ BS EN 6138:2017EN 6138:2017 (E) 5 3 Requirements 3.1 Configuration, dimensions, tolerances

23、 and mass The configuration, dimensions, tolerances and mass shall conform with Figure 1 and Table 1. Linear tolerances not specified, shall be in accordance with ISO 2768-m. All internal surfaces shall be free of burrs and moulding joints. Key 1 Area for marking Unless otherwise specified all radiu

24、s shall be R = (1,0 0,2) mm. Figure 1 Configuration and dimensions Table 1 Dimensions and mass Dimensions in millimetres Size codea A B C E F G Mass Thread per ISO 3161 g 04 .4375-20UNJF 17,0 13,9 10,1 8,6 12 0,9 06 .5625-18UNJF 20,5 17,3 10,3 8,8 15 1,3 08 .7500-16UNJF 25,5 22,1 12,4 10,9 20 2,2 10

25、 .8750-14UNJF 28,5 25,6 13,6 12,1 23 2,7 12 1.0625-12UNJ 33,5 30,6 14,8 13,3 28 3,7 16 1.3125-12UNJ 39,5 37,2 34 4,1 20 1.6250-12UNJ 48,5 45,3 42 6,5 24 1.8750-12UNJ 55,0 51,0 49 8,0 aSize code corresponds to the nominal tube diameter in 1/16 inch. BS EN 6138:2017EN 6138:2017 (E) 6 3.2 Material, sur

26、face treatment and colour The material and colour shall be in accordance with Table 2. The caps shall be resistant to phosphate ester hydraulic fluids according to EN 6102. The surface of the parts shall be free of burrs and moulding joints. Table 2 Material Code Material Density Melt Flow Index (MF

27、I) Colour Polyethylene (HD-PE) 0,940 to 0,970 7,5 to 15,0 Red (e. g. FED-STD-595C No. 11302 or No. 11310) 3.3 Sealing areas Contact surface mates with the dimensions and tolerances of the fitting part (see Figure 2). 3.4 Proof pressure 100 kPa (1 bar). 3.5 Temperature range 3.5.1 Storage and transpo

28、rtation temperature 54 C to 85 C. 3.5.2 Installation and removal At room temperature (25 10) C. 3.5.3 Cleanliness Parts shall be in accordance with SAE-AS4059 class 7 or better. 4 Technical requirement 4.1 General For qualification, three specimens per size shall be tested at a temperature of (25 10

29、) C. The requirements given in 3.3 have to be fulfilled. On the sealing area, there shall be a consistently good contact between cap and end fitting when hand tightened. After removal of the plugs, chips inside the equipment/tube/hose are not allowed. BS EN 6138:2017EN 6138:2017 (E) 7 4.2 First arti

30、cle inspection For first article inspection, the test assembly shall withstand a pressure equal the proof pressure (see 3.4) without leakage, evidence of permanent deformation or other malfunction, a period of 3 min after pressure stabilization. Six specimens shall be tested at a temperature of (25

31、10) C. 5 Designation This type of standard shall be designated according to the philosophy of the following example: 6 Marking The caps shall be legibly and permanently marked per EN 2424 style A with the following: the full standard part designation; manufacturers name; or trademark; or CAGE code.

32、7 Packaging All parts shall be delivered individually in suitable bags, which are marked per EN 2424 style G. The standard parts shall be protected against humidity, embitterment, impact, contamination and other negative influences by suitable approved materials, so that no damage or deterioration w

33、ill occur under normal transport and storage conditions. The packaging materials used shall conform with national health and safety requirements and shall not affect the appearance or quality of the packaged items. Cleanness requirements shall be kept up to package opening. Chlorine free package sha

34、ll be used. 8 Example of installation See Figure 2 and Figure 3. BS EN 6138:2017EN 6138:2017 (E) 8 Key 1 Sealing surface 2 Fitting end per EN 6079 or SAE-AS33514 Figure 2 Sealing surface for flareless fitting ends and hose ends Key 1 Sealing surface 2 Fitting end per SAE-AS4395 Figure 3 Sealing surf

35、ace for flared fitting ends 9 Technical specification 9.1 Simple standard part Caps are defined as simple standard parts, which do not need a specific technical specification. 9.2 Production lot (batch) A production lot according to this specification consists of parts or assemblies, which shall hav

36、e the same physical characteristics (dimensions, materials, manufacturing methods, heat treatment, surface finish, etc.), being manufactured under the same conditions and submitted together for inspection. 9.3 Materials Materials shall conform to the specifications as specified or described in detai

37、l in the product standard. Other materials not specified or described in the product standard, may be introduced by the manufacturer to ensure compliance with technical requirements. BS EN 6138:2017EN 6138:2017 (E) 9 The suitability of materials not specified in the product standard shall be verifie

38、d by qualification tests. Any changes to materials shall be approved by the customer prior to the next delivery. 9.4 Approval of manufacturers The manufacturers quality system shall conform to EN 9100 or equivalent. The purpose of these procedures is to ensure that a manufacturer has a quality syste

39、m and the capability for continuous manufacture and release of parts complying with the specified quality requirements. The granting of an approval of the manufacturer is a function of the Certification Authorities, or their appointed representative, who is a prime contractor. 9.5 Responsibility for

40、 inspection Unless otherwise specified in the contract or purchase order, the supplier is responsible for the completion of all inspection requirements as specified in this specification. The supplier may use his own or other approved facilities and inspection methods to achieve satisfactorily the i

41、nspection requirements as covered by this specification. The customer reserves the right to perform counter-acceptance tests to ensure performance attains the required characteristics. 9.6 Labelling All packages shall be permanently and legibly marked with the following: the full standard part desig

42、nation; manufacturers name and address; order or purchase number. 9.7 Unit and transport packages The products shall be packed in unit or transport packages that comply with the customers requirements. This page deliberately left blankThis page deliberately left blankBSI is the national body respons

43、ible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together busin

44、ess, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of

45、 all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Kno

46、wledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Developme

47、nt Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the inte

48、rnational standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or pu

49、blicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one