EN 803-1994 en Plastics Piping Systems - Injection-Moulded Thermoplastics Fittings for Elastic Sealing Ring Type Joints for Pressure Piping - Test Method for Resistance to a Short-.pdf

1、CEN ENx803 94 6 3404589 OLOOL77 687 6 b BRITISH STANDARD Plastics piping systems - Inj ection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust The European Standard EN 803 : 1994

2、 has the status of a British Standard UDC 621.643.00-986:678-073:620.162.4 BS EN 803 : 1995 BS 2782 : Part 11 : Method 11235 : 1995 . CEN EN*803 94 m 3404589 OLOOL78 5L3 m published under the authority of the Standards Board and Amd. No. Date comes into effect on 15 July 1995 0 BSI 1995 The followin

3、g BSI references relate to the work on this standard Committee reference PRi61 Draft for comment 92/45390 DC ISBN O 680 24222 6 BS EN 803 : 1995 lxt affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PR61, Plastics

4、piping systems and components, upon which the following bodies were represented: British Gas plc British Plastics Federation British Plumbing Fittings Manufacturers Association British Valve and Actuator Manufacturers Association Department of the Environment (British Board of Agrment) Department of

5、 the Environment (Building Research Establishment) Department of the Environment (Property and Buildings Directorate) Department of Transport Electricity Association Federation of Civil Engineering Contractors Health and Safety Executive Institute of Building Control Institute of Materials Instituti

6、on of Civil Engineers Institution of Gas Engineers Institution of Water and Environmental Management National Association of Plumbing, Heating and Mechanical Services Pipeline Industries Guild Plastics Land Drainage Manufacturers Association Society of British Gas Industries Society of British Water

7、 Industries Water Companies Association Water Services Association of England and Wales Contractors The foliowing bodies were also represented in the drafting of the standard, through subcommittees and panels: ERA lchnology Ltd. Engineering Equipment and Materials Users Association RAPRA Ethnology L

8、td. CEN EN*803 94 = 3404589 0100179 45T BS EN 803 : 1995 Contents Page Committees responsible Inside front page National foreword i Method Foreword 2 1 Scope 3 2 Principle 3 3 Apparatus 3 4 Test piece 3 5 Procedure 3 6 Test report 4 i CEN EN*803 94 W 3404589 OLOOL80 171 W BS EN 803 : 1995 National f

9、oreword This British Standard has been prepared under the direction of the Sector Board for Materials and Chemicals and is the English language version of EN 803 : 1994 Plastics piping systems - Injection-moulded themnoplastics.fittings for elastic sealing ring type joints fw pressure piping systems

10、 - Bst method for resistance to a short-terrn internal pressure without end thrust, published by the European Committee for Standardization (CEN). It is incorporated into BS 2782 Methods of testing plastics Part 11 Thmnmplasticspipes, fittings and valves, as Method 11235 : 1995, for association with

11、 related test methods for plastics materials and plastics piping components. This test method has been prepared for reference by other standards under preparation by CEN for specification of plastics piping systems and components. It has been implemented to enable experience of the method to be gain

12、ed and for use for other fresh applications. It is also for use for the revision or amendment of other national standards as practicable, but it should not be presumed to apply to any existing standard or specification which contains or makes reference to a different test method until that standard/

13、specification has been amended or revised to make reference to this method and adjust any requirements as appropriate. Warning note. This British Standard, which is identical with EN 803 : 1994, does not necessarily detail ali the precautions necessary to meet the requirements of the Health and Safe

14、ty at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the method should be operated only by trained personnel. Compliance with a British Standard does not of itself confer immunity from legal obligations. . ii CEN EN*803 94 3404589 0100181 008 EUROPEAN STANDARD

15、 EN 803 NORME EUROPENNE EUROPISCHE NORM April 1994 UIIC 62 1.643.06-986: 678.073: 620.162.4 Descriptors: Pipelines, pressure pipes, plastic tubes, pipe fittings, thermoplastic resins, joining, sealing rings, rubber, pressure tests, resistance tests English version Plastics piping systems - Injection

16、-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust Systmes de canalisations en plastiques - Raccords thermoplastiques mouls par injection bagues dtanchit pour canalisations avec p

17、ression - Mthode dessai de rsistance une pression interne de courte dure sans effet de fonds Kuns tsoff - Rohrleitungssysteme - Spritzguss-Formstcke aus Thermoplasten fr Steckmuff enverbindungen fr Druckrohrleitungen - Prfverfahren fr die Widerstandsfhigkeit gegen Kurzzeit-Innendruck ohne Axialbeans

18、pruchung This European Standard was approved by CEN on 1994-04-11. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical

19、references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN memb

20、er into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swed

21、en, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1994 Copyright reserved to CEN members Ref. No. EN 803 : 1994 E CEN EN*803 94 3404589 OLOOL82 T44 Pa

22、ge 2 EN 803 : 1994 Foreword This standard was prepared by CEN/TC 155, Plastics piping systems and ducting systems. This standard is based on the International Standard IS0 2035 : 1974 Unplasticized poly(viny1 chloride) (PVC) moulded fittings for elastic sealing ring type joints for use under pressur

23、e - Pressure-res.istance test, published by the International Organization for Standardization (ISO). It is a modification of IS0 2035 : 1974 for reasons of applicability to other plastics materials and/or other test conditions and alignment with texts of other standards on test methods. The modific

24、ations are: - no material is mentioned; - test parameters, except those common to all plastics, are omitted; editorial changes have been introduced. - The material-dependent parameters and/or performance requirements are incorporated in the System Standard(s) concerned. No existing European Standard

25、 is superseded by this standard. This standard is one of a series of standards on test methods which support System Standards for plastics piping systems and ducting systems. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end

26、orsement, at the latest by October 1994, and conflicting national standards shall be withdrawn at the latest by October 1994. According to the CENKENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany,

27、Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. . 1 Scope This standard specifies a method for testing the resistance to internal hydrostatic pressure at 20 OC of any ijection-moulded thermoplastics fittings with elastic seal

28、ing ring type joints for thermoplastics pressure pipes having a nominal diameter, b) the period of time, t, that the test piece is subjected to pressure. 3 Apparatus 3.1 Pressurizing device, including thermostatic and/or environmental controls, capable of maintaining the specified hydrostatic pressu

29、re, p (see item a) of the note to clause 2), to within f 2,5 !%, for the specified period of time, t (see item b) of the note to clause 2), and of maintaining the test piece at (20 f 2) OC. 3.2 Supporting device, to compensate for the end thrust(s) resulting from the application of internal pressure

30、. 3.3 Pressure gauge, capable of checking conformity to the specified test pressure, p (see 3.1). Page 3 EN 803 : 1994 4 Test piece The test piece shall comprise an assembly of one or more pipe sections and fittings including at least one fitting of the type to be tested. Unless otherwise specified

31、in the referring standard, the section(s) of pipe to be connected shall have a length of three times d, with a minimum of 250 mm. They shall be capable of withstanding the test pressure, p, required by the referring standard. Assembling of the test piece shall be carried out in accordance with the m

32、anufacturers instructions. 5 Procedure In any convenient order cany out the following steps. a) Connect the end of one of the pipe sections of the test piece to the pressurizing device (see 3.1). b) Close by appropriate means the other end(s) of the test piece. c) Fill the test piece with water at (

33、20 f 2) OC, taking care to bleed off all internal air. Wait for at least 20 min after filling to ensure equalization of temperature to (20 I 2) OC. Remove any moisture from the outside surface of the test piece. Apply hydrostatic pressure progressively in such a way that the test pressure, p, is rea

34、ched in not less than 30 s and not more than 300 s. Maintain the test piece environment at (20 f 2) OC for the specified period, t, or until prior failure Maintain the pressure, p, for the specified period, t, checking by means of the pressure gauge that the pressure is within I 2,5 % and ensuring t

35、hat no leakage occurs at any area of the test piece unless prior failure occurs. If any area of the assembly other than a fitting under test shows failure (e.g. failure of another joint or a pipe bursting), start the test again, if necessary using other test piece elements. Maintain the pressure unt

36、il the assembly has shown constant leaktightness for the period, t, or until the fitting(s) fail(s), whichever occurs first. Record the results accordingly. occurs. CEN EN4803 94 W 3404589 0100184 817 W Page 4 EN 803 : 1994 6 %st report The test report shall include the following information: a) a r

37、eference to this standard and to the referring standard; b) the size, type and nominal pressure of the fitting and the material from which the fitting is made; c) the identity of the batch or production run from which the fitting was sampled; d) the type(s) of pipe(s) connected to the fitting in the

38、 test assembly and the material(s) from which the pipe(s) is (are) made; e) the test pressure, p, in bars); f) the period of time, t, in hours, the test piece was subjected to pressure; g) the test temperature, in degrees Celsius; h) whether or not the fitting and/or its joints exhibited any signs o

39、f deterioration, leakage, fracture or any other form of failure as specified by the referring standard; i) if applicable, observations of any failures causing repetition of the test; j) any factors which may have affected the results, such as any incidents or any operating details not specified in t

40、his standard; k) the date of test. 1 bar = lo5 N/m2. BS EN 803 : 1995 BS 2782 : part 11 : Method 11235 : 1995 BSI 389 Chiswick High Road London W4 4AL 9507- 4- 0.5k- FP CEN EN8803 74 = 3404589 OLOOL85 753 = BSI - British Standards Institution BSI is the independent national body responsible for prep

41、aring British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for

42、 their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccuracy or ambiguity while using this British Standard should bring it to the atte

43、ntion of the Quality Manager, BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and

44、foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick: Tel: O181 996 7000; k: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, un

45、less otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Informa

46、tion Department at Chiswick: Tel: 0181 996 7111; Exx: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chisw

47、ick: Tel: 0181 996 7002; k: 0181 996 7001. Copyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of necessary details such as symbo

48、ls and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted wili be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. SBN O 580 24222 6 Product code 00515443 PRI/61