EN 820-4-2009 en Advanced technical ceramics - Thermomechanical properties of monolithic ceramics - Part 4 Determination of flexural creep deformation at elevated temperatures《先进技术.pdf

1、BS EN 820-4:2009ICS 81.060.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAdvanced technicalceramics Thermomechanicalproperties ofmonolithic ceramicsPart 4: Determination of flexural creepdeformation at elevated temperaturesThis British Standardwas published

2、under theauthority of the StandardsPolicy and StrategyCommittee on 31 July 2009 BSI 2009ISBN 978 0 580 63843 5Amendments/corrigenda issued since publicationDate CommentsBS EN 820-4:2009National forewordThis British Standard is the UK implementation of EN 820-4:2009. Itsupersedes DD ENV 820-4:2002 wh

3、ich is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee RPI/13, Advanced technical ceramics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionso

4、f a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 820-4:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 820-4July 2009ICS 81.060.30 Supersedes ENV 820-4:2001 English VersionAdvanced technical ce

5、ramics - Thermomechanical properties ofmonolithic ceramics - Part 4: Determination of flexural creepdeformation at elevated temperaturesCramiques techniques avances - Propritsthermomcaniques des cramiques monolithiques - Partie4 : Dtermination de la dformation par fluage en flexion tempratures leves

6、Hochleistungskeramik - ThermomechanischeEigenschaften monolithischer Keramik - Teil 4:Bestimmung der Kriechverformung unterBiegebeanspruchung bei erhhten TemperaturenThis European Standard was approved by CEN on 12 June 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations w

7、hich stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European St

8、andard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national sta

9、ndards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kin

10、gdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 820-4:2009: EBS EN 820-4

11、:2009EN 820-4:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Significance and use .5 5 Principle 5 6 Apparatus .5 6.1 Creep test loading jig 5 6.2 Heating device 6 6.3 Loading device .6 6.4 Deflection measuring device 7 6.5 Data recording system 9

12、 7 Test pieces .9 8 Procedure .9 8.1 Measurement of test piece dimensions 9 8.2 Setting up the test piece .9 8.3 Temperature stabilization 10 8.4 Test force . 10 8.5 Data recording . 11 8.6 Analysis . 11 9 Accuracy and interferences . 13 10 Test report . 13 Bibliography . 15 BS EN 820-4:2009EN 820-4

13、:2009 (E) 3 Foreword This document (EN 820-4:2009) has been prepared by Technical Committee CEN/TC 184 “Advanced technical ceramics”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end

14、orsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for ide

15、ntifying any or all such patent rights. This document supersedes ENV 840-4:2001. EN 820 consists of five parts, under the general title “Advanced technical ceramics - Methods of testing monolithic ceramics Thermomechanical properties“: Part 1: Determination of flexural strength at elevated temperatu

16、res Part 2: Determination of self-loaded deformation Part 3: Determination of resistance to thermal shock by water quenching Part 4: Determination of flexural creep deformation at elevated temperatures Part 5: Determination of elastic moduli at elevated temperatures According to the CEN/CENELEC Inte

17、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Ma

18、lta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 820-4:2009EN 820-4:2009 (E) 4 1 Scope This Part of EN 820 describes a procedure for undertaking flexural creep tests at elevated temperatures on advanced technical cerami

19、cs, mainly for the purposes of comparison of deformation behaviour of materials under stressed conditions and under any appropriate atmospheric condition. NOTE This European Standard does not provide a method of acquiring engineering performance data since the stress distribution under flexural load

20、ing is indeterminate. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 8

21、20-1, Advanced technical ceramics Methods of testing monolithic ceramics - Thermomechanical properties - Part 1: Determination of flexural strength at elevated temperatures EN 843-1, Advanced technical ceramics Mechanical properties of monolithic ceramics at room temperature - Part 1: Determination

22、of flexural strength EN 1006, Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of test pieces for the evaluation of properties EN 60584-1, Thermocouples - Part 1: Reference tables (IEC 60584-1:1995) EN 60584-2, Thermocouples - Part 2: Tolerances (IEC 60584-2:1989 + A1:19

23、89) EN ISO 7500-1, Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Verification and calibration of the force-measuring system (ISO 7500-1:2004) EN ISO/IEC 17025, General requirements for the competence of testing and calibration

24、laboratories (ISO/IEC 17025:2005) ISO 3611, Micrometer callipers for external measurement 3 Terms and definitions For the purposes of this document the following terms and definitions apply. 3.1 creep time-dependent non-elastic deformation of a material under an applied stress 3.2 creep rupture fail

25、ure of a test piece under nominally constant loading conditions resulting from an accumulation of microstructural damage 3.3 stress rupture catastrophic extension of a flaw having previously grown subcritically under constant nominal stress leading to failure of the test piece BS EN 820-4:2009EN 820

26、-4:2009 (E) 5 3.4 subcritical crack growth extension of existing cracks or flaws under stress which does not produce instant failure 4 Significance and use The test is intended to evaluate the deformation of a test piece under nominally constant force as a function of time at elevated temperatures.

27、In particular it can be used for materials comparison, or for determining the temperature at which creep deformation becomes significant for a prospective engineering use. During the course of such a test, the test piece can fracture. This can be due either to a subcritical crack growth process unre

28、lated to the mechanism of creep (stress rupture), or to the accumulation of creep damage leading to acceleration of creep rate and the linking of damage to form cracks (creep rupture). In some circumstances it is not possible to distinguish the mechanism of failure. In either case, the test piece li

29、fetime under the imposed temperature and stress conditions can be an important aspect of a materials performance. The analysis given in this European Standard (see 8.6) produces purely nominal data, assuming that the actual maximum nominal stress in the test piece is linearly proportional to the tes

30、t force applied and is constant during the test. Moreover, an additional assumption of linear dependence of strain on stress is made for some deflection measurement methods. Furthermore, it does not give engineering creep data equivalent to separate pure tensile or compressive conditions. In many ca

31、ses, the creep rate dependence is to the maximum stress, and can differ in tension and compression. Typically, the true maximum stress in the test piece is less than that calculated using Equation 1 because of faster relaxation at higher stress levels, and the true surface strain rate can be greater

32、 than a linear prediction in certain geometrical arrangements for determining the deformation, particularly if this is done using the relative displacement of the loading system. The Bibliography contains references to more detailed theoretical analyses of flexural creep accounting for such non-line

33、arities. 5 Principle The method involves supporting a bar test piece on two supports near its ends, heating it to the required elevated temperature which is maintained constant, applying a force to two loading points spaced symmetrically between the support points, and recording the deflection of th

34、e test bar with time. The deflection of the test piece is measured indirectly and continuously or at appropriate time intervals during the test using the displacement of the loading system (see e.g. Figure 1a), or by using contacting extensometer rods at given positions on the test piece (see e.g. F

35、igures 1b to 1e). The indirect measurement of deflection (Figure 1a) is converted into a nominal maximum surface strain in the test piece assuming a linear relationship between stress and accumulated strain. Similar assumptions are involved in analysing deflections between support points and the spa

36、n centre (Figure 1b and 1c). When employing displacement measurement between the loading points and the span centre (Figures 1d and 1e), the analysis assumes uniform curvature of the test piece, a linear relationship between strain and distance from the neutral axis, and equal behaviour in tension a

37、nd compression. The slope of the strain/time curve can be converted to a creep strain rate. 6 Apparatus 6.1 Creep test loading jig The test jig is essentially a four-point bend flexural test jig similar to that described in EN 820-1 for flexural strength testing at elevated temperatures. It comprise

38、s a pair of parallel 5 mm diameter support rods positioned 40 mm apart on a refractory supporting structure. These rods shall be free to roll to eliminate friction effects. In contrast to the articulating requirement in EN 820-1, articulation is not required provided that the rods are accurately par

39、allel in the horizontal plane to within 0,001 mm per mm length of rod. BS EN 820-4:2009EN 820-4:2009 (E) 6 The loading assembly comprises a similar pair of freely rolling rods positioned on a loading block. The spacing between these rods shall be between 30 % and 50 % of the spacing of the support r

40、ods. The loading block shall be free to articulate relative to the loading column in order to permit alignment of the loading rods on the test piece upper surface. NOTE 1 Subject to agreement between parties, other test piece support and loading spans can be employed. This can be particularly advant

41、ageous for creep-resistant materials. In addition, in some conditions it is recognized that freely rolling rollers, although preferred, may not be feasible. Such deviations from this method should be reported. The effect of restricted roller rotation may or may not be significant depending on the te

42、st material and the testing conditions. There is some evidence to suggest that the surface of glass-phase containing materials, or materials which oxidize to give a viscous glassy surface layer, can have a low coefficient of friction against the roller material at the test temperature, such that ove

43、r the period of the test any friction becomes negligible. However, this situation cannot always be guaranteed. The loading block shall be guided appropriately such that the loading rods are positioned mid-way between the support rods, thus centrally loading a test piece when placed on the support ro

44、ds. The parts of the loading jig shall be constructed from a ceramic material which is anticipated to be more resistant to deformation than the materials under test. In addition the support and loading rods shall be of a material which does not chemically react with the test piece. NOTE 2 Suitable m

45、aterials include high-purity alumina for use with most oxide-based test pieces, or sintered silicon carbide for most non-oxide ceramics. NOTE 3 Test jig parts manufactured from sintered silicon carbide or other silicon-based non-oxide ceramics develop oxidation films in a short period of time when e

46、xposed to temperatures typically above 1 300 C in an oxygen-containing atmosphere. This can cause prevention of rolling of rollers and impairment of jig function. 6.2 Heating device A heating device surrounds the loading jig in such a manner as permit access to the jig for the purposes of mounting a

47、nd demounting test pieces. The heating device shall be capable of maintaining a constant test piece temperature to 3 C over the duration of the test. The temperature of the test piece shall be recorded using a thermocouple manufactured in accordance with EN 60584-2 allowing the use of reference tabl

48、es in EN 60584-1 or, alternatively calibrated in a manner traceable to the International temperature scale ITS-90. The tip of the thermocouple shall be close to but not touching the test piece. It shall previously have been determined that the temperature of the test piece does not vary by more than

49、 3 C over its length when temperature has stabilized for more than 30 min. The heating device can incorporate or be incorporated within a vacuum or other appropriate chamber for control of gas atmosphere if appropriate to the determination. 6.3 Loading device The load shall be applied through a loading column to which the upper part of the jig is connected. The load can be generated by any appropriate means provided that a force constant to within 1 % can be generated at the test piece. The force applied to the test piece shall be calibrate