EN 840-1-2012 en Mobile waste and recycling containers - Part 1 Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design《手机浪费和回收容器-第1部分.pdf

1、BSI Standards PublicationBS EN 840-1:2012Mobile waste and recycling containersPart 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and designIncorporating corrigendum September 2014BS EN 840-1:2012National forewordThis British Standard is the UK implementa

2、tion of EN 840-1:2012. It supersedes BS EN 840-1:2004, which is withdrawn.BSI, as a member of CEN, is obliged to publish EN 840-1 as a British Standard. However, attention is drawn to the fact that during the develop-ment of this European Standard, the UK committee voted against its approval as a Eu

3、ropean Standard. Two of the major manufacturers of plastic wheeled containers have expressed concern regarding the apparent use of dimensions in the standard which would appear to exclude contain-ers presently on the market in the UK and in use by both public and private sectors. These concerns were

4、 addressed at a CEN working group meeting and the UK committee therefore wish to point out the following:a) the volume criteria present in Table 1 of the standard should be interpreted separately from the dimensions which appear in Table 2 and Table 3 of the standard, i.e. the two criteria, volumes

5、and dimensions are mutually exclusive; andb) products are included in EN 840-1:2012 if they fulfil EN 840-1:2004.The UK participation in its preparation was entrusted by Technical Committee B/508, Waste Management to Subcommittee B/508/1, Waste containers and associated lifting devices on refuse col

6、lection vehicles.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Pub

7、lished by BSI Standards Limited 2014.ISBN 978 0 580 82603 0ICS 13.030.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments/corrigenda iss

8、ued since publicationDate Text affected30 September 2014 National foreword updated to include additional informative textBRITISH STANDARDBS EN 840-1:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-1 December 2012 ICS 13.030.40 Supersedes EN 840-1:2004English Version Mobile waste and rec

9、ycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design Conteneurs roulants ordures mnagres et recyclables - Partie 1 : Conteneurs 2 roues de capacit infrieure ou gale 400 l pour lve-conteneurs peigne - Dimensions et conceptio

10、n Fahrbare Abfall- und Wertstoffbehlter - Teil 1: Behlter mit 2 Rdern und einem Nennvolumen bis 400 l fr Kammschttungen - Mae und Formgebung This European Standard was approved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the

11、conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard e

12、xists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national

13、standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia

14、, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved world

15、wide for CEN national Members. Ref. No. EN 840-1:2012: EBS EN 840-1:2012EN 840-1:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Volumes 55 Dimensions and design 56 Nominal mass .67 Safety and health requirements .68 Testing 69 Marking .610 Designation

16、 7Annex A (informative) Nomenclature . 12Annex B (informative) Recommendations for manufacturers of lifting devices . 16Annex C (informative) A-Deviations . 17Bibliography . 18BS EN 840-1:2012EN 840-1:2012 (E) 3 Foreword This document (EN 840-1:2012) has been prepared by Technical Committee CEN/TC 1

17、83 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by Ju

18、ne 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 840-1:2004. Technical changes since the latest ed

19、ition: The content was adapted to the current state of the art and revised editorially. Figure 3 The functional dimension 28 for frontal receivers and the dimension 28 were redefined. This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recycli

20、ng containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and design (the present document); Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices

21、Dimensions and design; Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices Dimensions and design; Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting d

22、evices Dimensions and design; Part 5: Performance requirements and test methods; Part 6: Safety and health requirements. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium,

23、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan

24、d, Turkey and the United Kingdom. BS EN 840-1:2012EN 840-1:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste and recycling containers with 2 wheels, with capacity up to 400 l to be used by comb lifting devices. 2 Normative references The following

25、 documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 840-5, Mobile was

26、te and recycling containers Part 5: Performance requirements and test methods EN 840-6, Mobile waste and recycling containers Part 6: Safety and health requirements EN 1501-5, Refuse collection vehicles General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicl

27、es EN ISO 11469, Plastics Generic identification and marking of plastics products (ISO 11469) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile waste and recycling containers and lifting devices in three language

28、s are given in Annex A. 3.1 mobile waste and recycling container appropriately designed container fitted with wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties containers 3.3 comb lifting device lifting device in which the picking-up system con

29、sists of a row of teeth and a locking system to retain the container during emptying 3.4 volume total space inside the container when the lid is closed Note 1 to entry: See Table 1. 3.5 nominal volume capacity volume stated by the manufacturer Note 1 to entry: See Table 1 without tolerances. Note 2

30、to entry: The English term “capacity“ and the French term “capacit“ are translated in the German version by the term “Nennvolumen“. BS EN 840-1:2012EN 840-1:2012 (E) 5 3.6 nominal load load mass as given in Clause 6 3.7 total permissible mass mass of the container plus the nominal load 3.8 functiona

31、l and safety dimensions essential dimensions which ensure the functionality and interchangeability of the container with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This standard identifies the two classes of containers: Class I - small size (n

32、ominal volume up to 200 l); Class II - large size (nominal volume between 200 l and 400 l). Within the two above-mentioned classes of containers the volumes shown in Table 1 are identified. Table 1 Volumes Volume in l 13560+18580+86120+612140+4010180+2510190+155210+155240+255260+4025340+390 20 For m

33、ethods of measuring capacity, see EN 840-5. The volumes shown in Table 1 correspond to mobile waste and recycling containers capacities at present used in Europe. Since there are some overlapping capacities due to the tolerances, client and manufacturer shall decide while ordering the capacity chose

34、n. Nominal volumes different from those referenced in Table 1 can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 10 % maximum measured according to EN 840-5. 5 Dimensions and design 5.1 The design of the containers need not correspond to the drawings given

35、in Figure 1. The functional dimensions given in Tables 2 and 3 shall be respected. 5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the lifti

36、ng device during the lifting operation. The frontal receiver shall correspond to one of the options given in Figure 2 (Form A or B). 5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during the emptying cycle. It/they shall be made with at least

37、2 fixing points and have at least one means of opening. 5.4 Each wheel shall be capable of withstanding a static load of 100 kg. BS EN 840-1:2012EN 840-1:2012 (E) 6 5.5 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.6 The contai

38、ner shall be able to be immobilised by design. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm3x nominal volume. 7 Safety and health requirements The container shall meet the safety and health requirements according to EN 840-6. 8 Testing The container

39、shall fulfil the performance requirements and the tests of EN 840-5. 9 Marking 9.1 Each container complying with the requirements of this European Standard shall be durably and readably marked on the body in a visible part with: number of this European Standard (EN 840-1); nominal volume; manufactur

40、ers name or trademark; total permissible mass, in kilograms; year and month of manufacturing. 9.2 Plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materials is allowed, presuming that all requirements of this standard are complied with

41、. BS EN 840-1:2012EN 840-1:2012 (E) 7 10 Designation The container complying with the requirements of this European Standard shall be designated as follows: Container EN 840-1 240 A 96 Description Standard number Nominal volume, in litres Frontal receiver form: A = frontal receiver form A B = fronta

42、l receiver form B Nominal load, in kilograms BS EN 840-1:2012EN 840-1:2012 (E) 8 Table 2 Dimensions for containers from 60 l to 180 l Class I (up to 200 l) Dimensions in millimetres Dimen-sion N 60 l 120 l 140 l 180 l Remarks Type a Type b 1a448 5 480 5 505 max. 505 max. 505 max. Total width of the

43、container 2a448 5 480 5 480 5 480 5 480 5 Width of the frontal receiver 3 530 max. 555 max. 555 max. 555 max. 755 max. 4 1 005 max 1005 max. 1 100 max. 1 100 max. Total height including handles on the lid 5a860 min.; 970 max. 860 min.; 970 max. 860 min.; 1030 max. 860 min.; 1030 max. 6 450 max. 490

44、max. 490 max. 490 max. 500 max. 7 1 010 max. 1010 max. 1 155 max. 1 200 max. 8 430 min.; 670 max. 430 min.; 670 max. 430 min.; 670 max. 560 min; 760 max For 300 mm wheels, the maximum dimension is 70 mm more. 9a410 max. 450 max. 450 max. 450 max. 465 max. 10 320 10 385 max 385 max. 385 max. 410 max.

45、 11a15200+15200+15200+15200+Larger wheels accepted 12a19 min. 19 min. 19 min. 19 min. 13a25,46+25,46+25,46+25,46+15a5313+5313+5313+5313+16a2221+2221+2221+2221+17 - - - This dimension is no longer used. 18a26 1 26 1 26 1 26 1 19a58 max. 58 max. 58 max. 58 max. 20 20 min. 20 min. 20 min. 20 min. 21a13

46、0 max. 130 max. 130 max. 130 max. 22 15 max. 15 max. 15 max. 15 max. 23 8033+8033+8033+8033+26a147 8 180 5 180 5 180 5 180 5 Compulsory dimensions when ribs are fitted, max. ribs thickness 6 mm A middle rib is allowed, but only for Volume 200 l 27 270 min. 270 min. 270 min. 270 min. 28 The dimension

47、 No 28has to correspond to the lifting device. Definition in accordance with comb dimension, standard and identification character of EN 1501-5 aCompulsory dimensions for functional and safety reasons. The other dimensions indicated are suggested recommended values. BS EN 840-1:2012EN 840-1:2012 (E)

48、 9 Table 3 Dimensions for containers from 210 l to 400 l Class II ( 200 l) Dimensions in millimetres Dimen-sion N 210 l 240 l 340 l 390 l Remarks Type a Type b Type a Type b 1a546 5 580 5 665 max. 755515+Total width of the container 2a546 5 480 5 580 5 655 max 515745+660 10 Width of the frontal rece

49、iver 3 730 max. 740 max. 880 max. 810 max. 4 1 100 max. 1 100 max. 1 115 max. 1 100 max. Total height including handles on the lid 5a860 min.; 1 030 max. 860 min.; 1 030 max. 860 min.: 1 030 max. 860 min.: 1 030 max. 6 565 max. 590 max. 650 max. 775 max. 7 1 180 max. 1 190 max. 1 250 max. 1 200 max. 8 560 min.; 760 max. 560 min; 760 max. 560 min; 760 ma