EN 941-2014 en Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications《铝及铝合金 烹饪器具的生产的圈和圈股票 分类》.pdf

1、BSI Standards PublicationBS EN 941:2014Aluminium and aluminiumalloys Circle and circle stockfor the production of generalapplications SpecificationsBS EN 941:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 941:2014. Itsupersedes BS EN 941:1996 which is with

2、drawn.The UK participation in its preparation was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contr

3、act. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83720 3ICS 77.150.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the author

4、ity of theStandards Policy and Strategy Committee on 31 May 2014.Amendments issued since publicationDate Text affectedBS EN 941:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 941 April 2014 ICS 77.150.10 Supersedes EN 941:1995English Version Aluminium and aluminium alloys - Circle and circ

5、le stock for the production of general applications - Specifications Aluminium et alliages daluminium - Disques et bauches pour disques pour applications gnrales - Spcifications Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial fr allgemeine Anwendungen - Spezifikationen This Europea

6、n Standard was approved by CEN on 13 March 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concer

7、ning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into

8、 its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Ge

9、rmany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE

10、FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 941:2014 EBS EN 941:2014EN 941:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4

11、3 Terms and definitions .4 4 Technical conditions for inspection and delivery 5 4.1 General 5 4.2 Orders or tenders.5 5 Mechanical properties .6 6 Tolerances on dimensions and form .6 6.1 General 6 6.2 Diameter 6 6.3 Thickness .6 6.4 Tolerances on flatness for circles6 BS EN 941:2014EN 941:2014 (E)

12、3 Foreword This document (EN 941:2014) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsemen

13、t, at the latest by October 2014 and conflicting national standards shall be withdrawn at the latest by October 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying

14、 any or all such patent rights. This document supersedes EN 941:1995. With regard the previous version, Clause 2 Normative references was updated; no new alloys were added. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to

15、 implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

16、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 941:2014EN 941:2014 (E) 4 1 Scope This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications. It app

17、lies to: Circles made out of hot or cold rolled circles stock by: Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm; Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm; Hot or cold rolled circle stock with a thickness from

18、 0,2 mm up to and including 200 mm and with a width up to 3 500 mm. It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards. 2 Normative references The following documents, in whole or in part,

19、 are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1:2008+A1:2009, Aluminium and aluminium alloy

20、s - Sheet, strip, and plate - Part 1: Technical conditions for inspection and delivery EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties EN 485-3:2003, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form

21、for hot-rolled products EN 485-4:1993, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations 3 Terms and definitions For the purposes of this docume

22、nt, the following terms and definitions apply. 3.1 circle circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a uniform thickness over 0,20 mm BS EN 941:2014EN 941:2014 (E) 5 3.2 circle stock flat rolled product of rectangular cross-section wit

23、h uniform thickness over 0,20 mm, supplied in coils, sheets, or plates, usually with sheared or sawn edges, and intended to be sawn, sheared or blanked into flat shapes to be subsequently formed, drawn, etc. Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 hot rolled circle

24、 and circle stock circle or circle stock whose final thickness is obtained by hot rolling 3.4 cold rolled circle and circle stock circle or circle stock whose final thickness is obtained by cold rolling 4 Technical conditions for inspection and delivery 4.1 General All the provisions of EN 485-1 sha

25、ll apply, except Clause 4 (orders and tenders) which is modified as follows: 4.2 Orders or tenders The order or tender shall define the product required and shall contain the following information: a) the form and the type of product: 1) the form of the product (circle and circle stock); 2) the desi

26、gnation of the aluminium or aluminium alloy; 3) the customer application, b) the metallurgical temper of the material for delivery according to EN 515 (degree of hardness or heat treatment condition) and, if different, the metallurgical temper for use; c) the number of this European Standard or Spec

27、ification number, or where none exists, the properties greed between purchaser and supplier; d) the dimensions and shape of the product as applicable: 1) thickness; 2) diameter of the circle; 3) width of the strip, sheet, or plate; 4) length of the sheet or plate; 5) internal and external diameters

28、of the coil; e) whether hot rolled or cold rolled tolerances apply; f) quantity: BS EN 941:2014EN 941:2014 (E) 6 1) mass or number of pieces; 2) tolerances on quantity if required; g) any requirements for certificates of conformity, test and/or analysis reports or inspection certificates; h) any spe

29、cial requirements agreed between purchaser and supplier : 1) marking of products; 2) references to drawings, etc. 5 Mechanical properties The mechanical properties shall conform to the requirements specified in EN 485-2. 6 Tolerances on dimensions and form 6.1 General All provisions of EN 485-3 and

30、EN 485-4 shall apply with the following amendments and additions. 6.2 Diameter Tolerances on diameters for circle shall conform to Table 1. These tolerances include the tolerances on roundness. NOTE For circle obtained by blanking the recommended standard diameters are: From 100 mm up to 500 mm nomi

31、nal diameter: every multiple of 5; Over 500 mm up to 1 000 mm nominal diameter: every multiple of 10. 6.3 Thickness Tolerances on thickness for hot rolled circle and circle stock shall conform to Table 2. They are identical to those specified in Table 1 of EN 485-3:2003 and are reproduced here for c

32、onvenience. The tolerances on thickness for cold rolled circle and circle stock shall conform to Table 3. They are identical to those specified in Table 1 of EN 485-4:1993 and are reproduced here for convenience. The partition into group I and group II of most common materials which may be used for

33、the present application shall be as shown in Table 4. 6.4 Tolerances on flatness for circles Tolerances on flatness for circles, expressed as a percentage of the diameter D and/or the measured chord length L, shall conform to Table 5. Deviation from flatness d, resulting from arching or buckling, sh

34、all be measured as shown in Figures 1 and 2, using a lightweight straightedge and a feeler gauge, dial gauge or scale, while the circle is resting on a horizontal base plate, concave side upwards. Two measurements shall be carried out with the straight edge respectively parallel and perpendicular to

35、 the rolling direction. BS EN 941:2014EN 941:2014 (E) 7 These tolerances do not apply to circles supplied in O or F tempers except for special agreement between supplier and purchaser. Table 1 Tolerances on diameter Dimensions in millimetres Specified thickness Method of production Diameter toleranc

36、es for specified diameter aover up to up to 600 over 600 up to 1 000 over 1 000 up to 1 600 over 1 600 up to 3 000 over 3 000 up to 3 500 0,2 4 Blanking 0,5 0,5 - - - circular sawing or shearing + 3 0 + 4 0 + 7 0 + 9 0 + 11 0 4 6 Blanking 0,7 0,7 - - - circular sawing or shearing + 4 0 + 5 0 + 8 0 +

37、 9 0 + 11 0 6 12 Blanking 1 1 - - - circular sawing or shearing + 4 0 + 5 0 + 8 0 + 10 0 + 12 0 12 50 circular sawing or shearing + 7 0 + 7 0 + 9 0 + 12 0 + 14 0 50 200 circular sawing or shearing + 10 0 + 10 0 + 12 0 + 14 0 + 16 0 aThese tolerances include the tolerances on roundness. BS EN 941:201

38、4EN 941:2014 (E) 8 Table 2 Thickness tolerances for hot rolled circle and circle stock Dimensions in millimetres Specified thickness Thickness tolerance for specified diameter or width over up to up to 1 250 over 1 250 up to 1 600 over 1 600 up to 2 000 over 2 000 up to 2 500 over 2 500 up to 3 500

39、2,5 4,0 0,28 0,28 0,32 0,35 0,40 4,0 5,0 0,30 0,30 0,35 0,40 0,45 5,0 6,0 0,32 0,32 0,40 0,45 0,50 6,0 8,0 0,35 0,40 0,40 0,50 0,55 8,0 10 0,45 0,50 0,50 0,55 0,60 10 15 0,50 0,60 0,65 0,65 0,80 15 20 0,60 0,70 0,75 0,80 0,90 20 30 0,65 0,75 0,85 0,90 1,0 30 40 0,75 0,85 1,0 1,1 1,2 40 50 0,90 1,0 1

40、,1 1,2 1,5 50 60 1,1 1,2 1,4 1,5 1,7 60 80 1,4 1,5 1,7 1,9 2,0 80 100 1,7 1,8 1,9 2,1 2,2 100 150 2,2 2,2 2,7 2,8 - 150 200 2,8 2,8 3,3 3,3 - BS EN 941:2014EN 941:2014 (E) 9 Table 3 Thickness tolerances for cold-rolled circle and circle stock Dimensions in millimetres Specified thickness Thickness t

41、olerances afor specified diameter or width up to 1 000 over 1 000 over 1 250 over 1 600 over 2 000 over 2 500 over 3 000 up to 1 250 up to 1 600 up to 2 000 up to 2 500 up to 3 000 up to 3 500 over Up to Material Group Material Group Material Group Material Group Material Group Material Group Materi

42、al Group Group I Group II Group I Group II Group I Group II Group I Group II Group I Group II Group I Group II Group I Group II 0,2 0,4 0,02 0,03 0,04 0,05 0,05 0,06 - - - - - 0,4 0,5 0,03 0,03 0,04 0,05 0,05 0,06 0,06 0,07 0,10 - - 0,5 0,6 0,03 0,04 0,05 0,06 0,06 0,07 0,07 0,08 0,11 - - 0,6 0,8 0,

43、03 0,04 0,06 0,07 0,07 0,08 0,08 0,09 0,12 - - 0,8 1 0,04 0,05 0,06 0,08 0,08 0,09 0,09 0,10 0,13 - - 1,0 1,2 0,04 0,05 0,07 0,09 0,09 0,10 0,10 0,12 0,14 - - 1,2 1,5 0,05 0,07 0,09 0,11 0,10 0,12 0,11 0,14 0,16 - - 1,5 1,8 0,06 0,08 0,10 0,12 0,11 0,13 0,12 0,15 0,17 - - 1,8 2 0,06 0,09 0,11 0,13 0

44、,12 0,14 0,14 0,16 0,19 - - 2,0 2,5 0,07 0,10 0,12 0,14 0,13 0,15 0,15 0,17 0,20 - - 2,5 3 0,08 0,11 0,13 0,15 0,15 0,17 0,17 0,19 0,23 - - 3,0 3,5 0,10 0,12 0,15 0,17 0,17 0,19 0,18 0,20 0,24 - - 3,5 4 0,15 0,20 0,22 0,23 0,25 0,34 0,38 4,0 5 0,18 0,22 0,24 0,25 0,29 0,36 0,42 5,0 6 0,20 0,24 0,25

45、0,26 0,32 0,40 0,46 6,0 8 0,24 0,30 0,31 0,32 0,38 0,44 0,50 8 10 0,27 0,33 0,36 0,38 0,44 0,50 0,56 10 12 0,32 0,38 0,40 0,41 0,47 0,53 0,59 12 15 0,36 0,42 0,43 0,45 0,51 0,57 0,63 15 20 0,38 0,44 0,46 0,48 0,54 0,60 0,66 20 25 0,40 0,46 0,48 0,50 0,56 0,62 0,68 25 30 0,45 0,50 0,53 0,55 0,60 0,65

46、 0,70 30 40 0,50 0,55 0,58 0,60 0,65 0,70 0,75 40 50 0,55 0,60 0,63 0,65 0,70 0,75 0,80 aWhen measuring the thickness, a zone 10 mm wide from the edges of the product shall be disregarded. BS EN 941:2014EN 941:2014 (E) 10 Table 4 Material groups Group I EN AW-1080A, EN AW-1070A, EN AW-1050A, EN AW-1

47、200 EN AW-3003, EN AW-3103, EN AW-3005; EN AW-3105 EN AW-4006, EN AW-4007 EN AW-5005, EN AW-5305, EN AW-5505, EN AW-5605, EN AW-5110, EN AW-5210, EN AW-5310, EN AW5050 EN AW-8011A Group II EN AW-2014, EN AW-2017A, EN AW-2024 EN AW-3004, EN AW-5040, EN AW-5049, EN AW-5251, EN AW-5052, EN AW-5154A, EN

48、 AW-5454, EN AW-5754, EN AW-5182 EN AW-5083, EN AW5086 EN AW-6061, EN AW-6082 EN AW-7020, EN AW-7021, EN AW-7022, EN AW-7075 Table 5 Circle - Flatness tolerances Specified thickness mm Maximum total deviation admax/D % over up to 6,5 50 0,4 50 150 0,3 aThese tolerances only apply to circles with a diameter greater than