1、 STD-BSI BS EN 957-ENGL 1778 I lb24bb7 0739422 587 m BRITISH STANDARD BS EN 957-8:1998 Stationary training equipment - Part 8: Steppers, stairclimbers and climbers - Additional specific safety requirements and test methods The European Standard EN 95741998 has the stains of a British Standard ICs 97
2、.220.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 967-8:1998 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect o
3、n 16 December 1998 O BSI 1998 National foreword This British Standard is the English ianguage version of EN 957-8: 1998. The UK participation in its preparation was entrusted by Technical Committee SW/136, Sports, playground and other recreational equipment, to Subcommittee SW/136/4, Stationary h-ai
4、ning equipment, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committe any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests inf
5、ormed them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secrem. Cross-references The British Standards which implement intemational or European publications referred to in this document may be found in the BSI Standards Catalogue under the sec
6、tion entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ali the necessary provisions of a conh-act Users of British Standards are responsible for their correct application.
7、 Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. Amendments issued since publication Amd.No. IDate I Te
8、xt affected ISBN O 580 30089 7 STDqBSI BS EN EUROPl3AN SrANDm NO- EUROPENNE EUROP- NOW 957-8-ENGL 1998 II ltb24bb 0739424 351 D EN 95743 June 1998 ICs 97.220.30 Descriptors: sport equipment, gymnastic equipment, fixed equipment, escalators, mountaineering, simulation, specifications, safety, tests,
9、technical notices Engush version Stationary tmirung equipment - safety requirements and test methods Part 8: steppers, stairclimbers and climbers - Additional specific Appareils dentranement fixes - Partie 8 Monteescaliem, escalatom et simuiaturs descalade - Prescriptions spcifiques de scuritk et mt
10、hodes dessai supplmentaires Stationre ?i.ainingsge - cantilever supports (cantilever surfaces) by more - other dimensions by more than 1/100. thanf= lA50; 6.4 Handrailshandlebars If equipped with handrails or handlebass, these shall show no permanent deformation of more than 3 % when tested in accor
11、dance with 6.5. Ail accessible edges shail be rounded with a radius of not less than 2,5 mm. Test in accordance with 6.6. O BSI 1998 6.5 Foot pedals and stairs Ail accessible edges of foot pedals and stairs shall be rounded with a radius of not less than 2,5 mm. When tested in accordance with IS0 59
12、04, the friction factor of the peWstair surface shall be more than 0,5. The minimum width of the foot pedais and stairs excluding the foot guards shall be 100 nun. 5.6 Endurance test When tested in accordance with 6.6, the trallung equipment shall withstand - 12 000 cycles for class H, and - 100 O00
13、 cycles for class S. After the test the training equipment shall be capable of functioning in accordance with the manufacturers instructions for the correct use and shall not show any signs of damage, e.g. oil leakage. 6.7 Free wheel In the case of air fan or flywheel assisted steppers, the trammisi
14、on assembly should be of a he wheel type. Test in accordance with 6.1.2 and 6.1.4. 5.8 Additional requirement for class A The variation of the indicated or determined power P from the power input shall not exceed k5 W up to 50 W and f10 % over 50 W. 6 Test methods 6.1 General 6.1.1 Dimensional check
15、. 6.1.2 Vual examination. 6.1.3 Tactile examination. 6.1.4 Peflormance test. 6.2 Testing of squeeze, shear and reciprocation points and of transmission elements and rotating parts Apparatus: - test finger probe B in accordance with EN 71-1 for classH, and - test finger in accordance with 6.6 of EN 9
16、57-1: 1996 for class S. Approach the test fingers from all sides to all moving Parts. Determine whether the nger is trapped. 6.3 Testing of temperature rise Apparatus: contact thermometer with an accuracy of fl “C. Carry out these tests using (100 5) kg test subjects. Operate the Imhhg equipment at
17、60 stepdmin fl0 % for 20 min. The step height shall be (180 i 5) nun when measured ai the centre of the foot pedal or the maximum possible step height of the equipment if this is not achievable. Page 7 EN 9578:1998 The resistance shall be set at the maximum resistance or reduced until 60 stepdmin ca
18、n be maintained without a pause between steps. Note whether the temperature has exceeded 65 OC. For speeddependent training machines carry out the test using a 100 kg load and a paddling speed producing a mechanical power of 180 W f 10 %. 6.4 Testing of intrinsic loading Set the resistance to a cond
19、ition which subjects the macme to a maximum stress. Apply the required test load F for classes H or S without shock for 5 min in the stop position to one pedal over a surface area of 90 nun X 90 mm. Remove the applied load and measure the deformation. Repeat for the other pedal. When more than one f
20、unction is tested, which involves the use of common components, e.g. ropes, pulleys, these can be replaced before each separate test. In order to test the whole drive system, e.g. linkages and frame, place the foot pedal at the mid-point of its range of movement and lock it at the fixing point of th
21、e resistance mechanism furthest away from the foot pedal (e.g. for a dependent stepper lock the other pedal). Apply the load F without shock in the most onerous position over a surface area of 90 mm X 90 mm of the foot pedal or stair so that the whole system is subjected to stress (see Figure 6). -
22、Figure 6 - Test of intrinsic loading The base frame of the training equipment shail not be fixed to the floor during the test unless instructed otherwise in the instnictions for use. O BSI 1998 STD-BSI BS EN 957-8-ENGL 1998 D Lb24bb7 0737431 59L = Page 8 EN 967-8:1998 6.6 Testing of handrailshandleb
23、ars Apply a force of 1 O00 N vertically in the most onerous position of the handrail or handlebar by means of a belt with a width of (80 f 5) mm for a period of 5 min. Next, apply a force of 500 N horizontally using the belt in the me position as in the vertical test but in the most onerous horizont
24、al direction of the handrails or handlebar for a period of 5 min. Determine the permanent deformation. 6.6 Endurance testing For speed-independent steppers cany out the test at 60 stepdmin f 10 % with a step height of 180 mm in the centre of the pedal movement or the maximum possible step height of
25、the equipment if this is not achievable, using a body mass of 100 kg for each foot pedai or stair. For speed-dependent steppers carry out the test with a step height of (180 5) mm in the centre of the pedal movement or the maximum step height if this is not achievable at a step speed which produces
26、an average of 180 W mechanical power f10 %. Perform the endurance test as follows: a) for class H, 12 O00 cycles working for 15 min and rest time 15 min and continue the same pattern until complete; b) for class S, 100 O00 cycles working for 10 h, cool down to room temperature, then continue for fur
27、ther 10 h and continue this method until the test is complete. Check the training equipment is capable of being used as per the manufacturers instsuctions for use. 6.7 Testing of the additional requirement for class A Compare the mechanical power input to the power display. Determine the mechanical
28、power input by calculating the input force over distance (range of movement) and time. The displayed value shall be within f10 % of this measured value in watts using the test parameters of the manufacturer, see clause 7c). The power input shall be the average of a 10 min test period. The test appar
29、atus for measuring force, distance and time shall be accurate to *I % for each of the three variables. 7 Additional instructions for use In addition to EN 957-1, easy-to-understand htructions for use shall be supplied with each stepper, stairclimber and climber. The instnictions for use shall includ
30、e information on at least the following points, depending on the class: a) information on the braking system (speed- dependentlspeed-independent); b) information on the stepping action (dependent or independent); c) for class A, the testing parameters, includuig the training speed, resistance settin
31、g and range of movement used in the test O BSI 1998 BS EN 957-8: 1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international
32、 level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards jhould make sure that they possess the latest amendments or editions. t is the constant aim of BSI to improve the quabl of our products and services. We would be
33、grateful if anyone finding an inaccuracy or ambiguity while using this British standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 0181 996 9000. Fax: 0181 996 7400. BSI offers members an individual updating se
34、rvice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel 0181 996 7000. Fax: 0181 996 7001. in response to orders for in
35、ternational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its
36、 Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel O181 996 7111. Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments
37、and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel 0181 996 7002. Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications o
38、f the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permissio
39、n from BSL This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 0181 996 7070.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1