EN 985-2001 en Textile Floor Coverings - Castor Chair Test《铺地织物 小脚轮轮椅试验》.pdf

1、BRITISH STANDARD Textile floor coverings - Castor chair test The European Standard EN 985:2001 has the status of a British Standard ICs 59.080.60 BS EN 985:2001 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 985:2001 National foreword This British Standard, having been

2、prepared under the direction of the Sector Policy and Strategy Committee for Materiais and Chemicals, was published under the authority of the Standards Policy and Strategy Committee on 31 August 2001 This British Standard is the official English language version of EN 9852001 It supersedes BS EN 98

3、51995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRUS, Textile floor coverings, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or propo

4、sals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement inte

5、rnational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to inc

6、lude all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the

7、EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. IDate 1 Comments Q BSI 31 August 2001 ISBN O 580 37749 O EUROPEAN STANDARD EN 985 NORME EUR

8、OPENNE EUROPISCHE NORM July 2001 ICs 50.080.60 Supersedes EN 985:1994 English version Textile floor coverings - Castor chair test Revtements de sol textiles - Essai a lappareil roulettes Textile Bodenbelge - Stuhlrollenprufung This European Standard was approved by CEN on 2 June 2001 CEN members are

9、 bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Upto-date lists and bibliographical references concerning such national standards may be obtained on application to the

10、 Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as

11、 the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy. Luxembourg, Netherlands, Noway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI

12、ON COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 9852001 E EN 985:2001 (E) Foreword This European Standa

13、rd has been prepared by Technical Committee CENiTC 134 “Resilient and textile floor coverings“, the secretariat of which is held by BSI. This European Standard replaces EN 985:1994. This European Standard shall be given the status of a national standard, either by publication of an identical text or

14、 by endorsement, at the latest by January 2002, and conflicting national standards shall be withdrawn at the latest by January 2002. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austr

15、ia, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. a 2 EN 985:2001 (E) 1 Scope This European Standard specifies three methods for assessing the behaviour of tex

16、tile floor coverings under the movement of a castor chair. - Test A: Assessment of the wear behaviour of textile floor coverings under the castor chair, - Test B: Assessment of the change in colour (glossing) of needled floor coverings without a pile, - Test C: Assessment of the general structural i

17、ntegrity of textile floor coverings. 2 Normative references This European Standard incorporates by dated or undated references, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated referen

18、ces, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 201 39, Textiles - Standard atmos

19、pheres for conditioning and testing (IS0 139.7973). IS0 1957, Machinemade textile floor coverings - Sampling and cutting specimens for physical tests. EN 1471, Textile floor coverings -Assessment of changes in appearance. EN 12529:1998, Castors and wheels - Castors for furniture - Castors for swivel

20、 chairs - Requirements. IS0 2424, Textile floor coverings - Vocabulay. 3 Terms and definitions For the purposes of this standard the terms and definitions given in IS0 2424 apply. 4 Principle A textile floor covering is submitted for a prescribed number of cycles to the action of three castors which

21、 produce an eccentric turning motion. At the end of each test: - the change in appearance in accordance with EN 1471 is assessed after 5 O00 cycles and 25 O00 cycles (Test A); - the change in colour by means of grey scales is assessed after 750 cycles (Test B); - the extent of deterioration of the s

22、pecimen is assessed after 10 O00 or 25 O00 cycles (Test C). 5 Test apparatus (Figure 1) 5.1 Circular, rotating testing platform, of diameter (800 15) mm on which the specimen support plate is mounted. The rotation speed of the testing platform shall be (19 I 1) r/min and the direction of rotation sh

23、all reverse at (180 5 20) s intervals. The stop time between reversals shall be (5 I 1) s. 3 EN 985:2001 (E) 5.2 Castor assembly, comprising a vertical shaft set in a bearing and a plate, R, on which the castors are mounted. This castor assembly is offset at a distance of (198 f 1) mm from the centr

24、e of the testing platform. The three castors (5.3) are arranged concentrically at 120“ intervals around the centre of the plate and at a distance of (130 f 1) mm from the centre of the plate. They are free to rotate so that they follow the rotation of the castor assembly. The rotation speed of the c

25、astor assembly shall be (50 f 1) rimin. The castor assembly when loaded has a mass of (90 k 1) kg that is divided equally over the three castors. The distance under load between the castor assembly plate R and the loadldrive plate C (castor plate clearance) shall be more than 3 mm at the point of me

26、asurement (see Figure 1). NOTE 1 The area of stress produced on the test specimen is detemined by the distance between the axes of revolution of the castor chair assembly and of the testing platforni and also by the distance of the castors from the centre of the plate. The stressed area is approxima

27、tely 0,3 m2 NOTE 2 The relationship between the rotation speed of the testing platform and that of the castor assembly causes a sharp reverse movement of the castors near the edges of the stressed area. 5.3 Castor Set, comprising three castors as illustrated in Figure 2 with the following dimensions

28、: diameter of castors (50 f 2) mm width of castors : (20 I 2) mm radius of curvature of castor tread: (130 L 5) mm crank distance: (32f 2)mm The distance between any two castor mountings shall be (225 15) mm. The castors shall be Type H in accordance with EN 12529:1998. The castor treads shall be ma

29、de from polyamide having hardness between 90 and 100 Shore scale A units and shall be replaced after every 2 million cycles of the testing platform, or earlier if necessary. 5.4 Lifting device, to raise the castor assembly above the testing platorm when the apparatus is stationary. 5.5 Cycle counter

30、, for setting the number of cycles of the testing platform. 5.6 Suction device, with a flow rate of 25 to 30 lis mounted over the entire width of the stressed part of the specimen, the height of this device being adjustable. 5.7 Specimen support, comprising a circular sheet of rigid plastic (e.g. po

31、lymethylmethacryiate) of (7 k 2) mm thickness and diameter (800 f 5) mm. The support is placed on the testing platform with the holes in the support locating on studs on the testing platform to prevent slippage. 5.8 Metal clamping ring, of height (IO I 2) mm, external diameter (700 f 5) mm and inter

32、nal diameter (680 I 5) mm, to hold loose laid tiles, or carpet over an underlay, in position during the test. 5.9 Brush vacuum cleaner, with rotating brush, driven by an independent motor. 6 Sampling and preparation of specimens 6.1 Sample the material to be tested according to IS0 1957. 6.2 Prepare

33、 the specimens as follows. 6.2.1 Test A Cut either three semicircles or six quadrants of radius (350 k 3) mm ensuring that the edges are parallel to andior at right angles to the direction of manufacture. Cut also a reference specimen with dimensions of 4 EN 985:ZOOl (E) (200 f 2) mm x (200 his Brit

34、ish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. re: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures chat subscribers automatically receive the

35、latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at htto:/www.bsi-. Cn response to orders for interna

36、tional standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Tech

37、nical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and r

38、eceive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001, Further information about BSI is available on the BSI website at htta:/www.bsi&gI.cobal Copyright Copyright subsists in

39、all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means

40、- electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.