EN 137100-1995 en Sectional Specification Fixed Aluminium Electrolytic a c Capacitors with Non- Solid Electrolyte for Motor Starter Applications Qualification Approval《分规范 电动机起动器用非.pdf

1、 CENELEC EN%L37L00 95 3V04583 0372520 019 BRITISH STANDARD Harmonized system of quality assessment for electronic components Sectional specification: Fixed aluminium electrolytic a.c. capacitors with non-solid electrolyte for motor starter applications - Qualification approval The European Standard

2、EN 137100 : 1995 has the status of a British Standard ICs 31.0GO.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 137100 : 1996 - CENELEC EN*337L00 95 m 3404583 0372523 T55 W Amd.No. Date The following BSI references relate to the work on this standard: Committee refer

3、ence EPWO/1 Draft for comment 9U03103 DC ISBN O 680 25602 2 BS EN 137100 : 1996 Textaected This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1996 O BSI 1996 Co

4、mmittees responsible for this British Standard The prepdon of this British Standard was entrusted by Technical Committee EPY40, Capcitors and resistors for electronic equipment, to Subcommittee EPW40/1, Capacitors and EM suppression components for electronic equipment, upon which the following bodie

5、s were represented BSI Testing Services Electrical instabtion Equipment Manufacturers Association Federation of the Electronics industry Muustry of Defence National Supervising Inspectorate (BSI-PC) Society of British Aerospace Companies Ltd. Amendments issued since publication CENELEC EN*137100 95

6、= 3404583 0172522 991 BS EN 137100 : 1996 Contents Committees responsible National foreword page Inside front cover ii Foreword Text of EN 137100 2 3 O BSI 1996 1 CENELEC EN*L37L00 95 = 3404583 0372523 828 BS EN 137100 : 1996 National foreword This British Standard has been prepared by Subcommittee

7、EPU40/1 and is the English language version of EN 137100 : 1995, Sectional sp together with the voting report, circulated as document CECC(Secretariat)36, it was approved as EN 137100 on 19950624. The following dates were fixed - latest date by which the EN has to be implemented at national level by

8、 publication of an identical national standard or by endorsement (dop) 1996-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn - (dow) 1997-07-01 Contents Foreword 1 1.1 1.2 1.3 1.4 1.5 2 2.1 2.2 3 3.1 3.2 3.3 3.4 3.5 4 4.1 4.2 4.3 4.4 4.5 4.6 General Scop

9、e Related documents Information to be given in detail specincation Terminology Marking Preferred ratings and characteristics Preferred climatic categories Preferred values of ratings Quality assessment procedures Primary stage of manufacture Structuray similar components Certified test records Quali

10、fication approval Quality conformance inspection Test and measurement procedures Preconditioning Visual examination and check of dimensions Electrical tests Robustness of terminations Resistance to soldering heat Solderability page 2 3 3 3 3 4 5 6 6 6 7 7 7 7 7 8 10 10 10 10 13 13 13 4.7 Rapid chang

11、e of temperature 4.8 Vibration 4.9 Container sealing 4.10 Damp heat, steady state 4.11 Endurance 4.12 Dielectric stability 4.13 Pressure relief Annex Al Test plan for qualification approval Annex A2 Test plan for quality cornformance inspection lot-by-lot tests Annex A3 Test plan for quahty conforma

12、nce inspection periodic tests Annex A4 Test schedule for qualification approval Annex B Discharge resistor Annex C Pennissible overloads for motor capacitors Annex D Guide for operation and installation of motor capacitors Page 14 14 14 15 15 16 17 18 19 20 21 25 26 27 O BSI 1996 _ CENELEC EN*137100

13、 75 3404583 O17252b 537 = Page 3 EN 137100 : 1995 1 - GENERBL 1.1 Scope This specification applies to aluminium electrolytic capacitors with non-solid electrolyte primarily intended for a.c. motor starting applications. It covers capacitors for connection to windings of asynchronous motors supplied

14、from a single- phase system having a frequency up to and including 100 Hz, with rated voltages up to and including 500 V. It prescribes preferred ratings and characteristics and selects from the specification EN 137000 the appropriate quality assessment procedures, tests and measuring methods and gi

15、ves general performance requirements for this type of capacitor. 1.2 Related documents IEC 62 IEC 68 EN 137000:1995 IEC 410 Marking codes for resistors and capacitors Basic environmental testing procedures Generic specification: Fixed a.c. aluminium electrolyte capacitors for use with motors Samplin

16、g plans and procedures for inspection by attributes Note - The above references apply to the current editions except for IEC 68 where the referenced edition shall be used. 1.3 Information to be prescribed in a detail specification Detail specifications shall be derived from the relevant blank detail

17、 specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an a

18、sterisk. Note - The information given in 1.3.1 may for convenience be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.3.1

19、Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dime

20、nsions are preferably to be stated in m. CENELEC EN*137100 95 3404583 0372527 473 E Page 4 EN 137100 : 1995 Normally numerical values shall be given for the length, the width and the height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and the diameter

21、 of the terminations. When necessary, for example when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the d

22、etail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.3.2 Mounting The detail specification shall specify the method of mounting

23、 to be applied for normal use and the method which is mandatory for the application of the vibration and the bump or the shock tests. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case the detail specification shall describe the mounting fixt

24、ures and they shall be used in the application of the vibration, bump and or shock tests. 1.3.3 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: (1) Rated capacitance range See 2.2.1 Note

25、- When products approved to the detail specification have different ranges, the following statement should be added: “The range of capacitance values available in each voltage range is given in the Register of Approvals“. (2) Particular characteristics Additional characteristics may be listed, when

26、they are considered necessary to specify adequately the component for design and application purposes. (3) Soldering The detail specification shall prescribe test methods, severities and requirements applicable for the solderability and resistance to soldering heat test. 1.3.4 Marking The detail spe

27、cification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.5 of this sectional Specification shall be specifically stated. 1.4 Terminology In addition to the the applicable terms and definitions of EN 137000, the following definitions apply: CENELEC EN

28、*k137100 95 m 3404583 0372528 30T m Page 5 EN 137100 : 1995 1.4.1 Capacitance of an electrolytic capacitor The capacitance of an equivalent circuit having capacitance and resistance in series measured with an alternating current of approximately sinusoidal wave form of the specified frequency. 1.4.2

29、 Type of capacitor Aluminium electrolytic capacitors used in motor applications are of two types: “Elyt glatt“ i.e. plain foil and “Elyt rauh“ i.e. etched foil. 1.5 Marking See 2.4 of EN 137000 with the following details: 1.5.1 The information given in the marking is normally selected from the follo

30、wing list; the relative importance of each item is indicated by its position in the list: a) Manufacturers name, abbreviated name or trademark b) Manufacturers type designation c) Rated capacitance (C,) in FF d) Tolerance on rated capacitance as a percentage (when the tolerance e) Rated voltage (U,)

31、 in “V a.c.“ or “V-“ f) Rated frequency (fR) in Hz g) Type of application e.g.“Motor Starting“ h) Rated duty cycle e.g. “3/1,67“ i) Type of capacitor: “Elyt glatt“ or “Elyt rauh“ j) Climatic category k) Year month (or week) of manufacture (if a code is used, it shall be 1) Discharge device, if any,

32、shall be indicated by wording or the symbol m) CECC mark n) Reference to the detail specification is asymmetric, the range of capacitance may also be given) according to TEC 62) 1.5.2 The capacitor shall be clearly marked with a) to m) above. Any duplication of information in the marking on the capa

33、citor should be avoided. 1.5.3 The package containing the capacitor(s) shall be clearly marked with items a), b), c), e), g), and k) with any other of the remaining items as is considered necessary. 1.5.4 Any additional marking shall- be so applied that no confusion can-arise. Page 6 EN 137100 : 199

34、5 2 - PREFERRED RATINGS AND CWCTEKISTICS 2.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 68-1. The minimum and the maximium temperature and the duration of the damp heat, steady state t

35、est shall be chosen from the following: Rated minimum temperature: - 40 OC, - 25 OC and - 10 OC Rated maximum temperature: t 55 OC, + 60 OC, + 70 OC and t 85 OC Duration of the damp heat steady state test: 4, 10, 21 and 56 days 2.2 Preferred values of ratings 2.2.1 Rated capacitance (5) Preferred va

36、lues of rated capacitance are: 1-,O - 1,25 - 1,60 - 2.0 - 2,5 - 3,O - 4,O - 5,O - 6,5 - 8,O - 0,9 KF and their decimal multiples Other values may be used. 2.2.2 Tolerance on rated capacitance Preferred values of tolerance on rated capacitance are: - io/+ 10 x - 201+ 20 I Asymmetric tolerances are pe

37、rmitted but no tolerance shall exceed 25 X. 2.2.3 Rated voltage (%) Preferred values of rated a.c. voltage are: 110 - 120 - 150 - 220 - 240 - 250 - 260 - 280 - 320 - 330 V r.m.s. Other values may be used. 2.2.4 Category voltage (U,) The category voltage is equal to the rated voltage unless otherwise

38、 stated in the detail specification. 2.2.5 Maximum voltage The maximum voltage shall be 1,25 times the rated voltage or the category voltage. CENELEC EN*337100 95 3404583 0372530 Tb Page 7 EN 137100 : 1995 3 - QUALITY ASSESSHENT PROCEDURES 3.1 Primary stage of manufacture The primary stage of manufa

39、cture is the winding of the capacitor element or equivalent operation. 3.2 Structurally similar components Capacitors considered as being structurally similar are capacitors produced with similar processes and materials, though they may be of different case sizes and capacitance and voltage values.

40、Structural similarity may be utilised in the sampling of capacitors for testing under quality conformance inspection. 3.3 Certified test records The information required in 3.9 of EN 137000 shall be made available when prescribed in the detail specification and when requested by a purchaser. After t

41、he endurance test the parameters for which variables information is required are the capacitance change, tan S and the insulation resistance. 3.4 Qualification approval The procedures for qualification approval testing are given in 3.5 of EN 137000. The schedule to be used for qualification approval

42、 testing on the basis of lot-by-lot and periodic tests is given in 3.5 of this specification. The procedure using a fixed sample size schedule is given in 3.4.1 and 3.4.2 below. 3.4.1 Sampling The fixed sample size procedure is described in 3.5.3(2) of EN 137000. The sample shall be representative o

43、f the range of capacitors for which approval is sought. This may or may not be the complete range covered by the detail specification. The sample shall consist of specimens having the lowest and the highest capacitance values for a given rated voltage; if a range of rated voltages is offered for qua

44、lification, then the sample shall consist of specimens having the highest and the lowest capacitance in the largest and the smallest case size at the highest and the lowest voltages of the range. When three or more rated voltages form part of the range, the endurance and dielectric stability tests s

45、hall be performed on samples from an intermediate voltage value of the range offered for qualification. The manufacturer shall provide data on the capacitance per unit of total outer surface area of the case for each capacitance value in the range. The capacitor with the maximum capacitance per unit

46、 area shall also be tested if this value exceeds that of the highest capacitance value in the range by 10 X or greater; similarly, the capacitor with the minimum capacitance per unit area shall also be tested if this value is less than that of the lowest capacitance in the range by 10 % or greater.

47、Note - In calculating the total surface area small protrusions, terminals and fixing studs shall be ignored. Thus for the approval of a single voltage, the testing is required of at least two or three values; for the approval of a range of voltages, the testing is required of at least four or six va

48、lues. CENELEC EN*137100 95 3404583 0172531 9T4 Page 8 EN 137100 : 1995 Spares are permitted as follows: - one per value which may be used to replace the permitted non-conforming item in Group “O“ - one per value which may be used as replacements for specimens which are non-conforming item because of

49、 incidents not attributable to the manufacturer. The number in Group “O“ assumes all groups are applicable. If this is not so the numbers may be reduced accordingly. When additional groups are introduced into the qualification approval test schedule, the number of specimens required for Group “O“ shall be increased by the same number as that required for the additional group. Annex Al gives the number of samples to be tested in each group or sub-group together with the permissible number of non-conforming items for qualification ap