EN 14353-2007 en Metal beads and feature profiles for use with gypsum plasterboards - Definitions requirements and test methods (Incorporates Amendment A1 2010)《与石膏板一起使用的金属串珠和结构要素 .pdf

1、BS EN 14353:2007ICS 91.100.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDMetal beads andfeature profiles foruse with gypsumplasterboards Definitions,requirements and testmethods+A1:2010National forewordThis British Standard is the UK implementation of EN 143

2、53:2007+A1:2010. It supersedes BS EN 14353:2007 which is withdrawn.The start and finish of text introduced or altered to amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated b

3、y !“.The UK participation in its preparation was entrusted to Technical Committee B/544/2, Gypsum based boards and ancillaries.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions o

4、f a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 14353:2007+A1:2010This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2008 BSI 2010Am

5、endments/corrigenda issued since publicationDate Comments 30 April 2010 Implementation of CEN amendment A1:2010ISBN 978 0 580 63863 3EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14353:2007+A1 January 2010 ICS 91.100.10 Supersedes EN 14353:2007English Version Metal beads and feature profiles

6、for use with gypsum plasterboards - Definitions, requirements and test methods Cornires et profils mtalliques pour plaques de pltre - Dfinitions, spcifications et mthodes dessai Hilfs- und Zusatzprofile aus Metall zur Verwendung mit Gipsplatten - Begriffe, Anforderungen und Prfverfahren This Europea

7、n Standard was approved by CEN on 18 November 2007 and includes Amendment 1 approved by CEN on 14 December 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any al

8、teration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by t

9、ranslation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, F

10、rance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE

11、 FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14353:2007+A1:2010: EEN 14353:2007+A1:2010 (E) 2 Contents page Foreword 3Introduction . 41 Scope 52 Normative ref

12、erences 53 !Terms, definitions, symbols and abbreviations“ 63.1 !Terms and definitions“ . 63.2 !Symbols and abbreviations“ . 74 Requirements . 84.1 Reaction to fire . 84.2 Flexural strength (expressed as bending behaviour) 84.3 Release of dangerous substances . 84.4 Additional technical requirements

13、 . 84.5 Protective coating 84.6 Functional requirements . 94.7 Dimensions and tolerances 105 Test methods 145.1 Sampling . 145.2 Dimensional measurements . 145.3 Profile dimensions . 165.4 Wing width 175.5 Wing open area 175.6 Determination of expansion and movement . 185.7 Determination of breaking

14、 strength of paper tape . 195.8 Determination of bending behaviour . 196 Evaluation of conformity . 206.1 General 206.2 Initial type testing 206.3 Factory production control . 207 Designation 218 Marking, labelling and packaging 22Annex A (normative) Sampling procedure for testing 23A.1 General 23A.

15、2 Sampling procedure 23Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive 25ZA.1 Scope and relevant characteristics . 25ZA.2 Procedure for attestation of conformity of metal beads and feature profiles . 26ZA.3 CE marking and l

16、abelling 28Bibliography 30BS EN 14353:2007+A1:2010EN 14353:2007+A1:2010 (E) 3 Foreword This document (EN 14353:2007+A1:2010) has been prepared by Technical Committee CEN/TC 241 “Gypsum and gypsum based products”, the secretariat of which is held by AFNOR. This document shall be given the status of a

17、 national standard, either by publication of an identical text or by endorsement, at the latest by July 2010 and conflicting national standards shall be withdrawn at the latest by July 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

18、 rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2009-12-14. This document supersedes EN 14353:2007. The start and finish of text introduced or altered by amendment is indicated in the text

19、 by tags!“XThis document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this docum

20、ent. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ir

21、eland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 14353:2007+A1:2010EN 14353:2007+A1:2010 (E) 4 Introduction Metal beads and feature profiles are produced in wide variety of siz

22、es and shapes. They are cold formed from mild steel sheets with various protective coatings or extruded or cold formed from aluminium. Some of the beads are faced with paper tape to enable them to be jointed. The materials, design and mechanical properties make them particularly suitable to provide

23、improved physical properties and/or enhanced decorative solutions to plasterboard assemblies. Metal beads and feature profiles may be fixed by various methods to the plasterboard and may be featured self-finished, featured with decoration or concealed by finishing with jointing compounds to receive

24、decoration. Figures 1 and 2 show the relationship between this standard and the set of standards prepared to support gypsum plasterboards. Figure 1 Family of gypsum products BS EN 14353:2007+A1:2010EN 14353:2007+A1:2010 (E) 5 Products from secondary processing Thermal/acoustic Composites EN 13950 Gy

25、psum plasterboard products from reprocessing EN 14190 Prefabricated partition panels EN 13915 Ancillary products Gypsum based adhesives EN 14496 Preformed cornices EN 14209 Jointing materials EN 13963 Metal components EN 14195 Metal beads and feature profiles EN 14353 Mechanical fasteners EN 14566 G

26、ypsum Plasterboard EN 520 Gypsum boards with fibrous reinforcement EN 15283-1 and EN 15283-2Figure 2 Family of ancillary products 1 Scope This European Standard specifies the characteristics and performance of metal beads, metal beads combined with paper tape and metal feature profiles designed for

27、use in systems made with gypsum plasterboards, gypsum boards with fibrous reinforcement and products from secondary processing complying with the ENs shown in Figure 2, intended to be used in building construction works. Metal beads and feature profiles, depending upon their material and type, can b

28、e featured without decoration, decorated or finished with jointing compounds to receive decoration. It covers the following performance characteristics: reaction to fire and flexural strength (bending behaviour) to be measured according to the corresponding European test methods. It provides for the

29、 evaluation of conformity of the product to this EN. This European Standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry and the reference tests for these characteristics. 2 Normative references The fol

30、lowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 520, Gypsum plasterboards Definitions, requirements a

31、nd test methods EN 755 (all parts), Aluminium and aluminium alloys Extruded rod/bar, tube and profiles BS EN 14353:2007+A1:2010EN 14353:2007+A1:2010 (E) 6 !EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold f

32、orming Tolerances on dimensions and shape EN 10139, Cold rolled uncoated mild steel narrow strip for cold forming Technical delivery conditions EN 10140, Cold rolled narrow steel strip Tolerances on dimensions and shape EN 10143, Continuously hot-dip coated steel sheet and strip Tolerances on dimens

33、ions and shape EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold forming Technical delivery conditions“ !deleted text“ !EN 10346, Continuously hot-dip coated steel flat products Technical delivery conditions“ EN 13501-1, Fire classification of construction products and

34、building elements Part 1: Classification using data from reaction to fire tests EN 13963, Jointing materials for gypsum plasterboards Definitions, requirements and test methods !EN 15283-1“, Gypsum boards with fibrous reinforcement Definitions, requirements and test methods Part 1: Gypsum boards wit

35、h mat reinforcement !EN 15283-2“, Gypsum boards with fibrous reinforcement Definitions, requirements and test methods !Part 2: Gypsum fibre boards“ !EN ISO 1924-2, Paper and board Determination of tensile properties Part 2: Constant rate of elongation method (20 mm/min) (ISO 1924-2:2008)“ !EN ISO 92

36、27, Corrosion tests in artificial atmospheres Salt spray tests (ISO 9227:2006)“ 3 !Terms, definitions, symbols and abbreviations“ For the purposes of this document, the following !terms, definitions, symbols and abbreviations“ apply. 3.1 !Terms and definitions“ !3.1.1“ metal bead profiled narrow sec

37、tion formed in steel or aluminium with a cross section to suit its application NOTE Beads may incorporate a variety of profiles and one or more wings depending upon their function. The wings can be perforated or expanded to facilitate fixing using mechanical and/or jointing compound methods. !3.1.2“

38、 angle bead profiled section used to enhance and protect external angles !3.1.3“ edge bead profiled section engaged to enclose and enhance and protect the edge of the plasterboard !3.1.4“ feature bead profiled section used to enhance the finish to the edge of the plasterboard BS EN 14353:2007+A1:201

39、0EN 14353:2007+A1:2010 (E) 7 !3.1.5“ stop bead profiled section used to provide a straight edge to receive the finish to the edge !3.1.6“ corner tape paper tape incorporating one or more metal or other strips to give added protection to external angles !3.1.7“ profile surface or edge with a cross se

40、ction to suit the application !3.1.8“ wing area adjoining the bead face or edge, usually perforated or expanded, used for support or fixing !3.1.9“ wing open area percentage of wing area perforated or expanded !3.1.10“ movement bead profiled section, composed of three parts, with flexibility to allo

41、w movement in both its length and width !3.1.11“ expansion bead profiled section with flexibility to allow movement across its width !3.1.12“ metal featured profile extrusion with a cross section to suit the application !3.1.13“ fin tapered section on one or both sides of the profile to assist joint

42、ing !3.1.14“ nominal dimension dimension or angle stated by the producer 3.2 !Symbols and abbreviations For the purpose of simplification in product marking and performance information characteristics may be identified through the symbols and abbreviations given in Table 1. Table 1 Symbols and abbre

43、viations Requirement Sub-clause Symbol or abbreviation Reaction to fire 4.1 R2F Flexural strength 4.2 F “ BS EN 14353:2007+A1:2010EN 14353:2007+A1:2010 (E) 8 4 Requirements 4.1 Reaction to fire When the intended use of metal beads and feature profiles is for fire exposed situations in building const

44、ruction works and if they are not coated with an organic material, they shall be classified in Euroclass A1 (no contribution to fire) without testing1). If they are coated with an organic material and subject to regulatory requirements, they shall be tested and classified in accordance with EN 13501

45、-1. 4.2 Flexural strength (expressed as bending behaviour) When tested in accordance with 5.8, individual lengths of beads or profiles shall show no fracture, kinks or permanent local deformations to the surface from the action of deflection. 4.3 Release of dangerous substances Materials used in pro

46、ducts shall not release any regulated substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination. 4.4 Additional technical requirements 4.4.1 Materials and surface aspect

47、!Metal beads and feature profiles shall be manufactured from steel strip conforming to EN 10346 or EN 10152. Alternatively, the metal strips for the corner tape strips may be manufactured from steel according to EN 10139 with a coating according to EN 10152 (for ZE coating) or to EN 10346 (for Z or

48、AZ coating). Aluminium beads and featured profiles manufactured according to EN 755 shall have a surface finish free from marks and imperfections to satisfy their exposed function.“ 4.4.2 Paper specifications The paper used to face corner tape shall be compatible with jointing compounds to EN 13963

49、and have a minimum breaking strength of 4,0 N/mm, when tested in accordance with 5.7. 4.5 Protective coating !Metal beads manufactured from steel strip shall have a protective coating conforming to one of the following standards: EN 10346 or EN 10152 (for corner tape only). The protective coating shall conform to one of the classes given in Table 2 or alternatively in Table 3 (for angle beads and corner tapes only). 1) See Commission Decision 96/603/E