EN 14392-2007 en Aluminium and aluminium alloys - Requirements for anodised products for use in contact with foodstuff《铝和铝合金 与食品接触的阳极产品的要求》.pdf

1、BRITISH STANDARDBS EN 14392:2007Aluminium and aluminium alloys Requirements for anodised products for use in contact with foodstuffICS 67.250; 77.150.19g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g4

2、0g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 14392:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 53127 9National forewordThis British Standard is the UK implementation of EN 14392:200

3、7.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contra

4、ct. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14392November 2007ICS 77.150.10; 67.250English VersionAl

5、uminium and aluminium alloys - Requirements for anodisedproducts for use in contact with foodstuffAluminium et alliages daluminium - Spcifications pour lesproduits anodiss destins entrer en contact avec lesalimentsAluminium und Aluminiumlegierungen - Anforderungen ananodisierte Erzeugnisse, die in K

6、ontakt mit LebensmittelnkommenThis European Standard was approved by CEN on 15 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date list

7、s and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the respons

8、ibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland

9、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassar

10、t, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14392:2007: EEN 14392:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Ordering information.5 5 Chemical com

11、position of the aluminium or aluminium alloy .5 6 Chemical composition of the anodization bath5 7 Sealing 5 7.1 General5 7.2 Composition of the sealing bath5 7.3 Technical parameters of the sealing process.6 7.4 Quality assurance and quality assessment 6 8 Demonstration of conformity with the presen

12、t standard 7 Annex A (informative) Adeviations8 EN 14392:2007 (E) 3 Foreword This document (EN 14392:2007) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This document shall be given the status of a national standard,

13、either by publication of an identical text or by endorsement, at the latest by May 2008 and conflicting national standards shall be withdrawn at the latest by May 2008. Within its programme of work, Technical Committee CEN/TC 132 has entrusted CEN/TC 132/WG 9 to prepare the following standard: EN 14

14、392, Aluminium and aluminium alloys Requirements for anodised products for use in contact with foodstuff. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rig

15、hts. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulati

16、ons, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla

17、nds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14392:2007 (E) 4 1 Scope This European Standard specifies requirements for coloured or uncoloured anodic oxidation coatings on wrought and cast products in aluminium and aluminium alloys for

18、 use in contact with food. These requirements cover the chemical composition of the bath, the sealing and the properties of the obtained anodic oxidation coatings. They do not cover dyestuffs and pigments but do cover the metallic deposits produced by electrolytic colouring. 2 Normative references T

19、he following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 601, Aluminium and aluminium alloys Castings Ch

20、emical composition of castings for use in contact with foodstuff EN 602, Aluminium and aluminium alloys Wrought products Chemical composition of semi products used for the fabrication of articles for use in contact with foodstuff EN 10204, Metallic products Types of inspection documents EN 12258-1:1

21、998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 12373-1, Aluminium and aluminium alloys Anodizing Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium EN 12373-4, Aluminium and aluminium alloys Anodizing Part 4: Estimation

22、of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment EN 12373-5, Aluminium and aluminium alloys Anodizing Part 5: Assessment of quality of sealed anodic oxidation coatings by measurement of admittance EN 12373-7, Aluminium and aluminium al

23、loys Anodizing Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1225

24、8-1:1998 and the following apply. 3.1 anodic oxidation coating coating obtained by an electrolytic oxidation process, having protective, decorative or functional properties 3.2 sealing treatment of anodic oxide coating to reduce porosity and the absorption capacity of the coating by hydrothermal pro

25、cesses carried out after anodising EN 14392:2007 (E) 5 3.3 order document document or set of documents agreed between supplier and purchaser at the time of ordering NOTE An order document can be an order of the purchaser confirmed by the supplier or a quotation of the supplier confirmed by the purch

26、aser. 4 Ordering information In addition to the information necessary for sufficient definition of the product and its properties as defined by EN 12373-1, order documents shall contain the following information: a) the number of this European Standard; b) any requirement on the periodicity of inspe

27、ction certificates (see Clause 8). 5 Chemical composition of the aluminium or aluminium alloy The chemical composition of the aluminium or aluminium alloys for use in contact with food, intended to be anodised, shall comply with the requirements of EN 601 or EN 602, as applicable. 6 Chemical composi

28、tion of the anodization bath The anodization of aluminium or aluminium alloy products intended to be in contact with foodstuff shall be carried out in a diluted aqueous solution of one or more of the following acids: sulfuric acid; sulfomaleic acid; sulfosalicylic acid; oxalic acid; sulfophtalic aci

29、d; phosphoric acid. 7 Sealing 7.1 General The anodic oxidation coating shall be sealed unless the coating has been produced in a bath containing only diluted phosphoric acid, or unless the product on which the anodic oxidation coating has been produced will receive another organic or inorganic coati

30、ng prior to use in contact with food. 7.2 Composition of the sealing bath Sealing shall be done in distilled or demineralized water, which may contain appropriate additives. The inspection certificate shall confirm that the additives and their respective concentrations in the sealing bath comply wit

31、h current legal requirements. EN 14392:2007 (E) 6 7.3 Technical parameters of the sealing process All the technical parameters of the sealing process, especially the temperature and pH of the bath, the duration of the treatment and the nature and concentration of additives shall be chosen to minimis

32、e the absorptive power of the anodic oxidation coating and maximise its chemical resistance and to minimizer the migration of potentially hazardous additives. 7.4 Quality assurance and quality assessment The producer shall set up a suitable quality assurance system in order to monitor the quality of

33、 the sealing. The method described in EN 12373-4 and EN 12373-5 shall be used for routine control, and the method described in EN 12373-7 for calibration purpose. NOTE Quality assurance and quality assessment can be done in the framework of a recognised European quality label such as QUALANOD1). 1)Q

34、UALANOD c/o AC Treuhand AG P.O. Box 1507 Tdistrasse 47 CH 8002 Zrich EN 14392:2007 (E) 7 8 Demonstration of conformity with the present standard The anodizing of aluminium and aluminium alloys products for use in contact with food shall be carried out in the framework of a quality assurance system.

35、This quality assurance system shall allow traceability of a delivered lot to the parameters of the production process that are relevant to the present standard (see Clauses 5 to 7). The manufacturer shall establish an inspection certificate “3.1“ according to EN 10204 which certifies compliance of t

36、he delivered products with the requirements of the present standard. Unless otherwise agreed upon between manufacturer and purchaser, this certificate can be issued at the discretion of the manufacturer either for each delivered lot, or periodically for all products delivered under the present stand

37、ard within a period of time not exceeding twelve months. EN 14392:2007 (E) 8 Annex A (informative) Adeviations A- deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN/CENELEC member. This European Standard does not fall und

38、er any Directive of the EU. In the relevant CEN/ CENELEC countries these A-deviations are valid instead of the provisions of the European Standard until they have been removed. Deviation 7.1 (France) The Order of 27th August 1987 concerning aluminium or aluminium alloys materials and objects in cont

39、act with foodstuffs, products and food drinks, article 5, enumerates authorized acids put in contact with the above products intended for the French territory. blankBS EN 14392:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible

40、for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or

41、editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the

42、 inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publicat

43、ions should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

44、 have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are al

45、so available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of

46、standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI i

47、s available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be repr

48、oduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size,

49、type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.