EN 14598-1-2005 en Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1 Designation《增强热固性模塑复合物 模压.pdf

1、BRITISH STANDARD BS EN 14598-1:2005 Reinforced thermosetting moulding compounds Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) Part 1: Designation The European Standard EN 14598-1:2005 has the status of a British Standard ICS 83.120 BS EN 14598-1:2005 This British S

2、tandard was published under the authority of the Standards Policy and Strategy Committee on 24 June 2005 BSI 24 June 2005 ISBN 0 580 46022 3 National foreword This British Standard is the official English language version of EN 14598-1:2005. Together with BS EN 14598-2:2005 and BS EN 14598-3:2005, i

3、t supersedes BS 5734-1:1990, BS 5734-2:1990, BS 5734-3:1990, and BS 5734-4:1990 which are withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A list of organizations rep

4、resented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Inde

5、x”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself conf

6、er immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulga

7、te them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comm

8、entsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14598-1 April 2005 ICS 83.120 English version Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation Mlanges mouler thermodurcissables renforcs - Spc

9、ification pour mats primprgns (SMC) et mlanges mouler en masse (BMC) - Partie 1 : Dsignation Verstrkte hrtbare Formmassen - Spezifikation fr Harzmatten (SMC) und faserverstrkte Pressmassen (BMC) - Teil 1: Bezeichnung This European Standard was approved by CEN on 21 February 2005. CEN members are bou

10、nd to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the C

11、entral Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status

12、as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia,

13、Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN natio

14、nal Members. Ref. No. EN 14598-1:2005: EEN 14598-1:2005 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope5 2 Normative references5 3 Terms and definitions .6 4 Designation system.6 4.1 General6 4.2 Data block 17 4.3 Data block 28 4.4 Data block 39 4.4.1 General9 4.4.2 Specific properties.9 4.4.3

15、 Designatory property #1 Flexural strength 9 4.4.4 Designatory property #2 Temperature resistance.9 4.5 Data block 410 4.6 Data block 510 5 Examples for designations .10 5.1 General10 5.2 Examples10 Bibliography 11EN 14598-1:2005 (E) 3 Foreword This document (EN 14598-1:2005) has been prepared by Te

16、chnical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdraw

17、n at the latest by October 2005. EN 14598 consists of the following parts, under the general title Reinforced thermosetting moulding compounds Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound BMC) Part 1: Designation Part 2: Methods of test and general requirements Part 3:

18、Specific requirements This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

19、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EN 14598-1:2005 (E) 4 Introduction This document establishes a data-block system for the designation of Sh

20、eet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) using a format and coding system established by the International Standards Organisation (ISO) which is common to most fibre reinforced thermoset and thermoplastic moulding materials. The system is intended to be applied only to materials

21、ready for commercial use. The designation system is based on the premise that thermosets and long fibre reinforced thermo-plastics can be divided into generic families using basic polymers, values of selected designatory properties and additional qualitative information in order to describe a partic

22、ular material as precisely as desired. The system is intended for the designation of a single material (or a small group of similar materials) within a generic family. It is not intended to specify by this system the chemical composition or the volumetric recipe of the compound but to designate the

23、material for identification purposes. It is the responsibility of the producer of the compound material to provide the appropriate designation. The data-block system is also the basis for specification given in Parts 2 and 3 of this document. To ensure that the meanings of codes remain unambiguous a

24、nd to avoid conflicts within the system codes and abbreviations have to be coordinated with ISO/TC 61/SC 1. EN 14598-1:2005 (E) 5 1 Scope This part of EN 14598 establishes a data block system for the designation of Sheet Moulding Compounds (SMC) and Bulk Moulding Compounds (BMC) The types of SMC and

25、 BMC are differentiated from each other by a classification system based on information about basic polymer parameters, fillers/reinforcement content and type, intended method of processing and/or manufacturing, specific characteristics and designatory properties. This document is applicable to all

26、SMC and BMC ready for normal use in the form of sheets and bulks. It is not intended to imply that materials having the same designation give necessarily the same performance. This part of EN 14598 does not provide engineering data, performance data or data on processing conditions which may be requ

27、ired to specify a material for a particular application and/or method of processing. Whenever general requirement data in the part 3 of this document need to be indicated, this data block system is also the basis for it. 2 Normative references The following referenced documents are indispensable for

28、 the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14598-2, Reinforced thermosetting moulding compounds Specification for Sheet Moulding compound (SMC) a

29、nd Bulk Moulding Compound (BMC) Part 2 : Methods of test and general requirements. EN 14598-3, Reinforced thermosetting moulding compounds Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3 : Specific requirements. EN ISO 75-2, Plastics Determination of tempera

30、ture of deflection under load Part 2: Plastics, ebonite and long- fibre-reinforced composites (ISO 75-2:2004) EN ISO 178, Plastics - Determination of flexural properties (ISO 178:2001) EN ISO 472:2001, Plastics Vocabulary (ISO 472:1999) EN ISO 1043-1:2001, Plastics Symbols and abbreviated terms - Pa

31、rt 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1043-2, Plastics Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043- 2:2000) EN ISO 14125, Fibre reinforced plastic composites Determination of flexural properties (ISO 14125:1998)EN 1459

32、8-1:2005 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472:2001, EN 14598-2, EN 14598-3 and the following apply. 3.1 Sheet Moulding Compound - SMC reinforced thermosetting moulding material, flat sheets 3.2 Bulk Moulding Compound - BMC rei

33、nforced thermosetting moulding materials, bulk 3.3 UP - SMC or UP - BMC reinforced thermosetting moulding material made on the basis of unsaturated polyester resins 3.4 VE SMC or VE - BMC reinforced thermosetting moulding material made on the basis of Vinyester resins 4 Designation system 4.1 Genera

34、l This designation system for EN 14598-1 is based on the following standardized pattern: Designation Description block Identity block European Standard Individual-item number block Number block Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 The designation consists of an optional d

35、escription block, reading “SMC” or “BMC” and an identity block comprising the European Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into 5 data blocks comprising the following information: The first character of the individual-item blo

36、ck shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (=no indication) but only if another block follows. For labelling purposes and if no other blocks follow the comma between block 1 and 2 can be omitted.

37、There is no need to fill in data blocks, if not required. EN 14598-1:2005 (E) 7 Data block 1 : Marking block. Item 1 : Identification of the basic polymer by its symbol in accordance with EN ISO 1043-1. Item 2 : Nature of the designatory reinforcing materials or fillers in accordance with EN ISO 104

38、3- 2. Item 3 : Form of the designatory reinforcing materials or fillers in accordance with EN ISO 1043-2. Item 4 : Nominal content according to Table 1. Data block 2 : Processing/manufacturing. Method of processing and/or manufacturing according to Table 2. Data block 3 : Properties. Item 1 : Specif

39、ic properties according to Table 3. Item 2 : Designatory property #1, flexural strength according to EN ISO 178, EN ISO 14125. Item 3 : Designatory property #2, temperature resistance according to EN ISO 75-2. Data block 4 : Further information Data block 5 : Optional 4.2 Data block 1 Item 1 : After

40、 the hyphen, unsaturated polyester Sheet Moulding Compound (SMC) or Bulk Moulding Compounds - BMC are identified by the symbol UP, in accordance with EN ISO 1043-1 Mixtures and modifications shall be coded in accordance with EN ISO 1043-1:2001 Clause 4 to 6 The following information shall be restric

41、ted to designatory fillers/reinforcements of the material in question: Item 2: Nature of filler/reinforcement according to Table 1. Item 3: Form of filler/reinforcement according to Table 1. Item 4: Nominal content (mass-%) of filler/reinforcement according to Table 1. Note, in particular, the follo

42、wing: the codes have different meanings when used as item 2 or item 3; whenever information needs to be indicated only for item3; an “X” ( = no indication) is required for item 2. EN 14598-1:2005 (E) 8 Table 1 Code letters and numbers used in data block 1 Nature of filler / reinforcement EN ISO 1043

43、-2 Form of filler / reinforcement EN ISO 1043-2 Percentage content code A Aramide B Balls; beads; spheres 05 7,5 % B Boron C Chips; cuttings 10 7,5 12,5 % C Carbon D Dust; powder 15 12,5 17,5 % D Alumina trihydrate F Fibre 20 17,5 22,5 % E Clay F1 Stable fibre 25 22,5 27,5 % G Glass F2 Chopped fibre

44、 30 27,5 32,5 % K Calcium carbonate G Ground, grist 35 32,5 37,5 % L1 Cellulose K Knitted fabric 40 37,5 42,5 % L2 Cotton M1 Mat cont. strand mech. bonded 45 42,5 47,5 % M Mineral M2 Mat cont. strand chem. bonded 50 47,5 52,5 % P Mica M3 Mat chop. strand mech. bondet 55 52,5 57,5 % Q Silica M4 Mat c

45、hop. strand chem. bondet 60 57,5 62,5 % R Recycled material N Non woven fabric 65 62,5 67,5 % S Synthetic organic P Paper 70 67,5 72,5 % T Talc S Scale, flake 75 72,5 77,5 % W Wood T Cord 80 77,5 82,5 % X No indication U Unidirectional contin. 85 82,5 87,5 % Z Others W Woven fabric 90 87,5 92,5 % X

46、No indication 95 92,5 97,5 % Z Others Mixtures of materials and/or forms may be indicated by combining the relevant codes using the sign “+“ and placing the whole between parenthesis. For example a mixture of 20 % glass fibres (GF) and 20 % mineral dust (MD) would be indicated by (GF20+MD20) or (GF+

47、MD) 20. 4.3 Data block 2 In this data block, information about the method of processing and/or manufacturing is given according to Table 2. Table 2 Code letters used in data block 2 Recommended method of processing G General purpose T Transfer moulding M Injection moulding X No indication Q Compress

48、ion moulding Z Others Any indication of an intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more than one way, e.g. compression moulding (Q) and injection moulding (M). Such brands are not special modifications and shall be des

49、ignated “general purpose“ (G). The designation of special methods of processing shall be reserved only for suitably modified materials.EN 14598-1:2005 (E) 9 4.4 Data block 3 4.4.1 General In this data block, the specific properties are represented by a code letter (see 4.3.1), as item 1 and designatory properties (see 4.3.2 and 4.3.3) as items 2 and 3 starting with an oblique stroken. If a designatory property value falls on or near a range limit,