EN 14758-1-2012 en Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1 Specifications for pipes fitti.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14758-1:2012Plastics piping systems fornon-pressure undergrounddrainage and sewerage Polypropylene with mineralmodifiers (PP-MD)Part 1: Specifications for pipes, fittings a

2、ndthe systemBS EN 14758-1:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14758-1:2012.It supersedes BS EN 14758-1:2005+A1:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/1, Plastics piping for non-

3、pressure applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Pub

4、lished by BSI StandardsLimited 2012ISBN 978 0 580 75371 8ICS 23.040.01; 93.030Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2012.Amendments issued since

5、 publicationDate Text affectedBS EN 14758-1:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14758-1 March 2012 ICS 23.040.01 Supersedes EN 14758-1:2005+A1:2009English Version Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (P

6、P-MD) -Part 1: Specifications for pipes, fittings and the system Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Polypropylne avec modificateurs minraux (PP-MD) - Partie 1: Spcifications pour les tubes, les raccords et le systme

7、Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstcke und das Rohrleitungssystem This European Standard was approved by CEN on 22 January 2012. CEN members are bound to compl

8、y with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

9、Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the sam

10、e status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

11、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by

12、 any means reserved worldwide for CEN national Members. Ref. No. EN 14758-1:2012: EBS EN 14758-1:2012EN 14758-1:2012 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions, symbols and abbreviations 6 3.1 Terms and definitions . 6 3.2 Symbols . 9 3.3 Abbreviations .

13、 9 4 Material . 10 4.1 PP-MD material 10 4.2 Reprocessable and recyclable material . 10 4.3 Melt mass-flow rate 10 4.4 Mineral modifiers 10 4.5 Resistance to internal pressure . 11 4.6 Sealing ring retaining means . 12 5 General characteristics 12 5.1 Appearance 12 5.2 Colour . 12 6 Geometrical char

14、acteristics . 12 6.1 General 12 6.2 Dimensions of pipes . 12 6.3 Ring stiffness classes 16 6.4 Dimensions of fittings . 16 6.5 Dimensions of sockets and spigots 17 6.6 Types of fittings 21 7 Mechanical characteristics of pipes . 23 7.1 Mechanical characteristics of pipes . 23 7.2 Mechanical characte

15、ristics of fittings . 25 8 Physical characteristics . 26 8.1 Physical characteristics of pipes 26 8.2 Physical characteristics of fittings 26 9 Performance requirements 27 10 Sealing rings 28 11 Marking. 28 11.1 General 28 11.2 Minimum required marking of pipes . 28 11.3 Minimum required marking of

16、fittings . 29 11.4 Additional marking 30 Annex A (informative) General characteristics of PP-MD pipes and fittings 31 A.1 General 31 A.2 Material characteristics 31 A.3 Ring stiffness 31 A.4 Chemical resistance . 32 BS EN 14758-1:2012EN 14758-1:2012 (E) 3 A.5 Abrasion resistance 32 A.6 Hydraulic rou

17、ghness . 32 A.7 Diametric deflection 32 Annex B (informative) Standards for pipes and fittings of a material other than PP-MD . 33 Bibliography . 34 BS EN 14758-1:2012EN 14758-1:2012 (E) 4 Foreword This document (EN 14758-1:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics piping s

18、ystems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the l

19、atest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14758-1:2005+A1:2009. In this rev

20、ised document the following changes are made: relevant test methods are changed from EN to ISO versions; the long term durability test are removed. The System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“, wh

21、ich is a Technical Committee of the International Organization for Standardization (ISO). The System Standards are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional req

22、uirements and on recommended practice for installation. EN 14758 consists of the following parts under the general title Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Part 1: Specifications for pipes, fittings and the system P

23、art 2: Guidance for the assessment of conformity (published as CEN/Technical Specification) Part 3: Guidance for installation (published as CEN/Technical Specification). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im

24、plement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

25、Switzerland, Turkey and the United Kingdom. BS EN 14758-1:2012EN 14758-1:2012 (E) 5 1 Scope This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underg

26、round drainage and sewerage outside the building structure (application area code “U“), and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D“) and outside the building structure. This is reflected in the marking of produ

27、cts by “U“ and “UD“. It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the

28、 purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes

29、and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This European Standard is applicable to PP-MD pipes with or without an inte

30、gral socket. NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Requirements and limiting values for application area code “D“ are given in Table 4, Table 7 and Table 13. NOTE 4 Pipes, fittings and other components conforming to any of

31、the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13. 2 Normative references The following documents, in whole or in

32、part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials requireme

33、nts for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN ISO 472:2001, Plastics Vocabulary (ISO 472:1999) EN ISO 580:2

34、005, Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) EN ISO 1043-1:2001, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 113

35、3:2005, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) EN ISO 1167 (all parts), Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure BS EN 14758-1

36、:2012EN 14758-1:2012 (E) 6 EN ISO 2505:2005, Thermoplastics pipes Longitudinal reversion Test method and parameters (ISO 2505:2005) EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions (ISO 3126) EN ISO 13967, Thermoplastics fittings Determination of ring stiffness (I

37、SO 13967) EN ISO 13968, Plastics piping and ducting systems Thermoplastics pipes Determination of ring flexibility (ISO 13968) EN ISO 9969, Thermoplastics pipes Determination of ring stiffness(ISO 9969) ISO 3127, Thermoplastics pipes Determination of resistance to external blows Round-the-clock meth

38、od ISO 11173, Thermoplastics pipes Determination of resistance to external blows Staircase method ISO 13257, Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling ISO 13259, Thermoplastics piping systems for underground non-pressure ap

39、plications Test method for leaktightness of elastomeric sealing ring type joints ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength ISO 13264, Thermoplastics piping systems for non-pressure underground d

40、rainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this European Standard, the terms, definitions and symbols given in EN ISO 472:2001 and

41、 EN ISO 1043-1:2001 and the following apply. 3.1.1 application area code code used in the marking of pipes and fittings to indicate the application area for which they are intended, as follows: U: code for the area more than 1 m from the building to which the buried piping system is connected; D: co

42、de for the area under and within 1 m from the building where the pipes and the fittings are buried in ground and are connected to the soil and waste discharge system of the building Note 1 to entry: In code D application areas, the existence of hot water discharge in addition to the external forces

43、from the surroundings is usual. 3.1.2 Geometrical definitions 3.1.2.1 nominal size DN numerical designation of the size of a component, which is a convenient round number approximately equal to the manufacturing dimension, in millimetres BS EN 14758-1:2012EN 14758-1:2012 (E) 7 3.1.2.2 nominal size D

44、N/OD nominal size, related to the outside diameter 3.1.2.3 nominal outside diameter dnspecified outside diameter, in millimetres, assigned to a nominal size (DN/OD) 3.1.2.4 outside diameter devalue of the measurement of the outside diameter through its cross section at any point of a pipe or spigot

45、end of a fitting, rounded up to the next greater 0,1 mm 3.1.2.5 mean outside diameter demvalue of the measurement of the outer circumference of a pipe or spigot end of a fitting in any cross section, divided by ( 3,142), rounded to the next greater 0,1 mm 3.1.2.6 mean inside diameter of a socket ds,

46、m arithmetical mean of a number of measurements of the inside diameter of a socket in the same cross section 3.1.2.7 wall thickness e value of the measurement of the wall thickness at any point around the circumference of a component 3.1.2.8 mean wall thickness emarithmetical mean of a number of mea

47、surements of the wall thickness, regularly spaced around the circumference and in the same cross section of a component, including the measured minimum and the measured maximum values of the wall thickness in that cross section 3.1.2.9 pipes series S number for pipe designation SOURCE: ISO 4065(1) 3

48、.1.2.10 standard dimension ratio SDR numerical designation of a pipe series, which is a convenient round number approximately equal to the ratio of the nominal outside diameter, dn, and the minimum wall thickness, eminBS EN 14758-1:2012EN 14758-1:2012 (E) 8 3.1.2.11 nominal ring stiffness SN numeric

49、al designation of the ring stiffness of a pipe or fitting, which is a convenient round number, relative to the determined stiffness in kiloNewtons per square metre (kN/m2), indicating the minimum ring stiffness of a pipe or fitting 3.1.2.12 design length Z length of a fitting (e.g. the main pipe of a branch) excluding any spigot or socket length. In case of a change in direction (e.g. in case of a bend or the service pipe of a branch), it is the length from one end to the intersection of the straight ax