EN 15156-2006 en Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Determination of fatigue properties at constant amplitude《高级陶瓷技术 环境.pdf

1、BRITISH STANDARDBS EN 15156:2006Advanced technical ceramics Mechanical properties of ceramic composites at room temperature Determination of fatigue properties at constant amplitudeThe European Standard EN 15156:2006 has the status of a British StandardICS 81.060.30g49g50g3g38g50g51g60g44g49g42g3g58

2、g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 15156:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September

3、 2006 BSI 2006ISBN 0 580 49052 1National forewordThis British Standard was published by BSI. It is the UK implementation of EN 15156:2006. The UK participation in its preparation was entrusted to Technical Committee RPI/13, Advanced technical ceramics.A list of organizations represented on RPI/13 ca

4、n be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd

5、. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15156August 2006ICS 81.060.30English VersionAdvanced technical ceramics - Mechanical properties of ceramiccomposites at room temperature - Determination of fatigueproperties at constant amplitudeCramiques techniques avances - Propr

6、its mcaniquesdes cramiques composites temprature ambiante -Dtermination des proprits de fatigue amplitudeconstanteHochleistungskeramik - Mechanische Eigenschaften vonkeramischen Verbundwerkstoffen bei Raumtemperatur -Bestimmung der Dauerschwingeigenschaften beiBelastung mit konstanter AmplitudeThis

7、European Standard was approved by CEN on 14 July 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references co

8、ncerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own

9、language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

10、Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of expl

11、oitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15156:2006: EEN 15156:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms, definitions and symbols.4 4 Principle8 5 Significance and use .8 6 Apparatus .9 6.1 Fatigue test machine .

12、9 6.2 Load train10 6.3 Extensometer .10 6.4 Data recording system 10 6.5 Micrometers10 7 Test specimens11 8 Test specimen preparation.12 8.1 Machining and preparation.12 8.2 Number of test specimens12 9 Test procedure.12 9.1 Measurement of test specimen dimensions .12 9.2 Testing technique 12 9.3 Te

13、st validity 13 10 Calculation of results 13 10.1 Time to failure, tf13 10.2 Damage parameters 14 10.3 Residual properties .14 11 Test report 16 Annex A (informative) Schematic evolution of E .17 EN 15156:2006 (E) 3 Foreword This document (EN 15156:2006) has been prepared by Technical Committee CEN/T

14、C 184 “Advanced technical ceramics”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn a

15、t the latest by February 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icel

16、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15156:2006 (E) 4 1 Scope This European Standard specifies the conditions for the determination of constant-amplitude of loa

17、d or strain in uniaxial tension/tension or in uniaxial tension/compression cyclic fatigue properties of ceramic matrix composite materials (CMCs) with fibre reinforcement at room temperature. This European Standard applies to all ceramic matrix composites with fibre reinforcement, unidirectional (1D

18、), bi-directional (2D), and tri-directional (xD, where 2 150 0,5 l, calibrated length 30 to 80 0,5 h, thickness 2 0,2 b1, width in the calibrated length 8 to 20 0,2 b2, width B2= b1with = 1,2 to 2 0,2 r, radius 30 2 Parallelism of machined parts 0,05 - EN 15156:2006 (E) 12 8 Test specimen preparatio

19、n 8.1 Machining and preparation During cutting out, care shall be taken to align the test specimen axis with the desired fibre related loading axis. Machining parameters which avoid damage to the material shall be established and documented. These parameters shall be adhered to during test specimen

20、preparation. 8.2 Number of test specimens At least three valid test results, as specified in 9.3 are required for any condition. 9 Test procedure 9.1 Measurement of test specimen dimensions The cross-section area shall be determined at the centre of the specimen and at each end of the gauge length.

21、The cross-section area varies with temperature and the variation is very difficult to measure. For this reason, the cross-section area shall be measured at room temperature. Dimensions shall be measured to an accuracy of 0,01 mm. The arithmetic means of the measurements shall be used for calculation

22、s. 9.2 Testing technique 9.2.1 Specimen mounting Install the test specimen in the gripping system with its longitudinal axis coincident with that of the test machine. Care shall be taken not to induce flexural or torsional loads in the test specimen. 9.2.2 Setting the extensometer If used, install t

23、he extensometer centrally within the calibrated length. 9.2.3 Measurements zero the load cell; zero the extensometer, if applicable; set the maximum number of cycles, N; for method A, set the maximum and minimum stress values; for method B, set the maximum and minimum strain values; set the frequenc

24、y and the wave shape; EN 15156:2006 (E) 13 start the fatigue test: for method A, in load control mode; for method B, in strain control mode; record the number of cycles N or Nf; if an extensometer is used, record the stress-strain loops up to the total number of cycles. NOTE A specific computer prog

25、ram is recommended to control the test. Depending on the computerized facilities used, all the loops can be recorded. If this is not possible, the following sequence can be used to record stress versus strain: every cycle for the first 10 cycles, one cycle every 10 cycles between 10 and 100 cycles,

26、one cycle every 100 cycles between 100 and 1 000 cycles, one cycle every 1 000 cycles between 1 000 and 10 000 cycles, etc. 9.3 Test validity The following circumstances shall invalidate a test for the determination of the lifetime duration: failure to specify and record test conditions; specimen sl

27、ippage in the grips. In addition, the following circumstances shall invalidate a test for the determination of the damage parameter: extensometer slippage; extensometer drift. 10 Calculation of results 10.1 Time to failure, tfCalculate the time to failure in accordance with the following equation: t

28、f(hours) = Nf/ (f x 3 600) where Nfis the number of cycles required to obtain failure of the test specimen; f is the frequency, in hertz (Hz). EN 15156:2006 (E) 14 10.2 Damage parameters Calculate the damage parameter Dnfor each recorded cycle, n, in accordance with the following equation: app1,appn

29、,n1EED = where Dnis the damage parameter at the nthfatigue cycle; En,appis the secant modulus of the nthfatigue loop (see Figure 4); E1,appis the secant modulus of the first fatigue loop (see Figure 4); Enappis equal to: (max) / (max nresidual) (see Figure 4). nresidualis equal to: (unl+l)/2 (see Fi

30、gure 4 b). The damage parameters, Dn, max, residcan be plotted versus the number of cycles, N. For N, a log scale is almost always used, although a linear scale may also be used. Figures 4 a) to 4 c) represent three cases of cyclic fatigue of CMCs. NOTE Annex A shows the schematic evolution of E und

31、er different circumstances of damage and creep. 10.3 Residual properties When rupture does not occur before the end of the test, the test specimen shall be tested to rupture in accordance with EN 1892, EN 1893 or EN 658-1. EN 15156:2006 (E) 15 a) R = 0 b) R 0 Key 1 strain () 2 stress () 3 cycle 1 4

32、Cycle n lloading unlunloading Figure 4 Fatigue stress-strain curves with a) R = 0, b) R 0 EN 15156:2006 (E) 16 11 Test report The test report shall contain the following information: a) name and address of the testing establishment; b) date of the test, unique identification of report and of each pa

33、ge, customers name, address and signature; c) a reference to this European Standard, i.e. EN 15156; d) test specimen drawing or reference; e) description of the test material (material type, manufacturing code, batch number); f) description of the test set up: extensometer, gripping system, load cel

34、l; g) frequency in hertz; h) wave form; i) maximum and minimum stress (method A); j) maximum and minimum strain (method B); k) number of cycles to failure; if test is stopped at a specified number of cycles without failure occurring it shall be so registered; l) residual properties (if applicable);

35、m) number of tests carried out and number of valid results obtained; n) damage parameter, if applicable; o) failure location of all the specimens used for obtaining the above results, if applicable. EN 15156:2006 (E) 17 Annex A (informative) Schematic evolution of E Figure A.1 shows a schematic evol

36、ution of E where there is a) no damage, b) creep but no fatigue damage and c) fatigue damage and eventual creep. a) No damage b) No fatigue damage only creep c) Fatigue damage plus eventual creep Key 1 first cycle 2 last cycle Figure A.1 Schematic evolution of E with a) no damage, b) creep but no fa

37、tigue damage and c) fatigue damage and eventual creep BS EN 15156:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level.

38、 It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be gratefu

39、l if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updati

40、ng service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: order

41、sbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wi

42、de range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)2

43、0 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002.

44、 Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also

45、holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recor

46、ding or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.