EN 15436-3-2015 en Road service area maintenance equipment - Part 3 Classification《道路服务区维修设备 第3部分 分类》.pdf

1、BSI Standards PublicationBS EN 15436-3:2015Road service area maintenanceequipmentPart 3: ClassificationBS EN 15436-3:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 15436-3:2015. It supersedes DD CEN/TS 15436-3:2009 which is withdrawn. The UK participation

2、in its preparation was entrusted to Technical Committee B/513, Construction equipment and plant and site safety.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U

3、sers are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 87752 0 ICS 43.160 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority o

4、f the Standards Policy and Strategy Committee on 31 July 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15436-3 July 2015 ICS 43.160 Supersedes CEN/TS 15436-3:2009English Version Road service area maintenance equipm

5、ent - Part 3: Classification Matriel dentretien des dpendances routires - Partie 3: Classification Straenbetriebsdienstausstattung - Teil 3: Klassifikation This European Standard was approved by CEN on 14 May 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

6、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European S

7、tandard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the

8、national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

9、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any

10、 means reserved worldwide for CEN national Members. Ref. No. EN 15436-3:2015 EBS EN 15436-3:2015EN 15436-3:2015 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Performance requirements .5 4.1 Criteria 5 4.2 Tolerances on characteristics

11、for machine construction .5 Bibliography 7 BS EN 15436-3:2015EN 15436-3:2015 (E) 3 Foreword This document (EN 15436-3:2015) has been prepared by Technical Committee CEN/TC 337 “Road operation equipment and products”, the secretariat of which is held by AFNOR. This document supersedes CEN/TS 15436-3:

12、2009. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2016, and conflicting national standards shall be withdrawn at the latest by January 2016. Attention is drawn to the possibility that

13、some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Compared to the previous version, this new document is now a standard which includes few simplifications in order to clarify its

14、application in conjunction with EN 15436-2. EN 15436, Road service area maintenance equipment, is composed with the following parts: Part 1: Terminology; Part 2: Performance assessment; Part 3: Classification the present document; Part 4: Delivery acceptance of the machines by the users. According t

15、o the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greec

16、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15436-3:2015EN 15436-3:2015 (E) 4 Introduction Road service area grass cutting, brush cuttin

17、g and mechanical plant cutting operations require special equipment that meets clearly defined technical criteria. This document defines and describes the classification criteria of the machines with respect to their kinematic and power performances. The performance evaluation is described in EN 154

18、36-2. BS EN 15436-3:2015EN 15436-3:2015 (E) 5 1 Scope This European Standard defines the classification criteria of the road service area maintenance equipment described in the scope of EN 15436-1 and used for: grass cutting and brush cutting; mechanical plant cutting. This equipment is mounted on s

19、elf-propelled carrying vehicles, and is intended, on the one hand, for cutting and shredding grass and brushwood, and, on the other hand, for trimming trees, saplings and bushes in road service areas. This document is intended to be used also in conjunction with EN 15436-2. 2 Normative references Th

20、e following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 15436-

21、1:2008, Road service area maintenance equipment - Part 1: Terminology EN 15436-2:2015, Road service area maintenance equipment Part 2: Performance assessment 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15436-1:2008 and EN 15436-2:2015 apply. 4 Per

22、formance requirements 4.1 Criteria Machine shall fulfil the 4 h testing method (as described in EN 15436-2:2015, 7.4.2 or 8.4.2) and has a cutting tool stopping time 5 s for a width of the cutting head 1,6 m or 7 s for a width of the cutting head 1,6 m. 4.2 Tolerances on characteristics for machine

23、construction The tolerances on each characteristic between the value declared by the manufacturer and the measured value are given in Table 1. BS EN 15436-3:2015EN 15436-3:2015 (E) 6 Table 1 Tolerances on each kinematic characteristic Accepted tolerances on the characteristics Kinematic characterist

24、ics Dimensional characteristics Cutting width (w) (for each cutting head) 2 cm Cutting height (h) (for each cutting head) 0,5 cm Cutting head clearance angle 2 angles 1and 23 Horizontal range (A) 1,5 % Horizontal clearance (Dh) 1,5 % Embankment range (E) or (R = E+F) 1,5 % Ditch range ( D1) or (D =

25、E+F) 1,5 % Ditch range with slide rail (D2) 1,5 % Offset (S) or (Dp) 1,5 % Variable offset 1,5 % Vertical range (B) 1,5 % Hedge size range (I) 5 % Hedge side position variation ( I) 5 % Maximum hedge topping height (C) 2 % Transfer dimensions and weight Maximum height (H) + 0 ; 4 cm Width (L1+L2) 2

26、cm Length (Lg1) 5 cm Length (Lg2) 5 cm Machine weight without balancing masses (Pt) 4 % BS EN 15436-3:2015EN 15436-3:2015 (E) 7 Bibliography 1 EN 13524, Highway maintenance machines Safety requirements This page deliberately left blankThis page deliberately left blankBSI is the national body respons

27、ible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chisw

28、ick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and re

29、fined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting ou

30、r website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need inter

31、national and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to B

32、ritish Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial disco

33、unts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find

34、 out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available,

35、 you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity

36、 within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the informa

37、tion used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any fo

38、rm or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW