EN 15816-2011 en Polymer-modified bituminous thick coatings for waterproofing - Resistance to rain《防水用聚合物改性沥青厚涂层 抗雨性》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15816:2011Polymer-modifiedbituminous thick coatings forwaterproofing Resistance torainBS EN 15816:2011 BRITISH STANDARDNational forewordThis British Standard is the UK impl

2、ementation of EN 15816:2011. The UK participation in its preparation was entrusted to TechnicalCommittee B/546, Flexible sheets for waterproofing and water vapour control.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpo

3、rt to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 62267 0 ICS 91.100.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the S

4、tandards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 15816:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15816 March 2011 ICS 91.100.50 English Version Polymer-modified bituminous thick coatings for waterproofing - R

5、esistance to rain Revtements bitumineux pais modifis aux polymres pour impermabilisation - Rsistance la pluie Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Widerstand gegen Regen This European Standard was approved by CEN on 13 February 2011. CEN members are bound to comp

6、ly with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

7、 Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the sa

8、me status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, P

9、ortugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any me

10、ans reserved worldwide for CEN national Members. Ref. No. EN 15816:2011: EBS EN 15816:2011EN 15816:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Principle 45 Apparatus .46 Test specimens 56.1 General 56.2 Preparation .56.3 Dimensions of the test spec

11、imens.66.4 Conditioning of test specimens .67 Procedure .67.1 Test conditions 67.2 Procedure .68 Expression of results and precision 68.1 Expression of results 68.2 Precision .69 Test report 6BS EN 15816:2011EN 15816:2011 (E) 3 Foreword This document (EN 15816:2011) has been prepared by Technical Co

12、mmittee CEN/TC 361 “Project Committee Polymer modified bituminous thick coatings for waterproofing Definitions/requirements and test methods”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text

13、or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respon

14、sible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finlan

15、d, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15816:2011EN 15816:2011 (E) 4 1 Scope This European Standard specifies a proced

16、ure for determining the resistance to rain of polymer modified bituminous thick coatings for waterproofing. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

17、the latest edition of the referenced document (including any amendments) applies. EN 206-1, Concrete Part 1: Specification, performance, production and conformity FprEN 15814:2011, Polymer modified bituminous thick coatings for waterproofing Definitions and requirements ISO 228-1, Pipe threads where

18、 pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation ISO 554, Standard atmospheres for conditioning and/or testing Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in FprEN 15814:2011 and the follow

19、ing apply. 3.1 resistance to rain resistance of the polymer modified bituminous thick coatings to the damaging effects of exposure to rain 4 Principle The test provides an indication of the resistance of a freshly applied polymer modified bituminous thick coating to rain. The time after which a coat

20、ing layer can be said to be resistant to rain under the conditions prevailing on the building site can vary quite considerably from the time determined in the laboratory. The measured values are therefore primarily suitable for use to compare the resistance of different products to rain. 5 Apparatus

21、 5.1 Sprinkler (see Figure 1) Standard conical nozzle made of copper-zinc alloy, pipe thread to ISO 228-1 G1/4B, sprinkler cone 85, flow rate 9l/min at 3 bar operating pressure; commercial pressure regulator with pressure gauge to indicate test pressure of (2 0,1) bar; specimen holder to position th

22、e specimen at an angle of 45 to the sprinkling plane. 5.2 Nozzle holder to position the nozzle; the nozzle shall be placed such that the vertical distance between the nozzle and the centre of the surface of the specimen is 25 cm. 5.3 Connection to water mains, hoses, connectors. 5.4 Stop watch BS EN

23、 15816:2011EN 15816:2011 (E) 5 5.5 Specimens: Base of concrete with a smooth or ground surface, of a compressive strength class not less than C20/25 in accordance with EN 206-1, to which a coating with an area of around 150 mm 150 mm can be applied. Key 1 connection to water mains gauge 2 pressure r

24、egulator with pressure 3 standard nozzle 4 specimen 5 specimen holder (at 45 angle) 6 outlet Figure 1 Sprinkler 6 Test specimens 6.1 General At least two specimens are required for the test. 6.2 Preparation The base shall be prepared and coated with a polymer modified bituminous thick coating as spe

25、cified in the manufacturers instructions for application. A wet layer with an average thickness of (3 0,3) mm shall be applied. The edges shall be trimmed. BS EN 15816:2011EN 15816:2011 (E) 6 6.3 Dimensions of the test specimens Test specimen with a size of approximately 150 mm 150 mm. 6.4 Condition

26、ing of test specimens After coating, the specimens shall be left to stand for a period of time specified by the manufacturer, but not longer than 8 h in a normal climate of (23 2) C and a relative humidity of (50 5) % in accordance with ISO 554. 7 Procedure 7.1 Test conditions The test shall be carr

27、ied out at (25 5) C. 7.2 Procedure The specimens shall be tested after conditioning. Prior to the test the water pressure shall be set at (2 0,1) bar when the water is running. Measure the temperature of the water. Two specimens shall be tested either simultaneously in two test rigs or one immediate

28、ly after the other in the same test rig. Place the specimen(s) in the holder under running water and start the stop watch. The test shall last 15 min. During the test, the water running off the test specimens shall be assessed for discolouration. If necessary, repeat the test using different specime

29、ns. 8 Expression of results and precision 8.1 Expression of results The water running off the test specimens shall not be discoloured during the test and the coating shall not deteriorate (e.g. surface erosion, water trapped in the material). In the event of such deterioration the test shall be repe

30、ated with a longer conditioning period on other specimens until at least two samples pass the test. The test result shall be the shortest conditioning period in which two samples produce no discolouration, stated to 0,5 h. This is the time in which a layer of freshly applied polymer modified bitumin

31、ous thick coating can be described as resistant to rain as defined in this test specification. The period shall not exceed 8 h. 8.2 Precision Precision data are currently not available. 9 Test report The test report shall include at least the following information: a) a reference to this European St

32、andard (i.e. EN 15816); b) all details necessary to identify the product tested; c) test procedure including any deviations from the test conditions; BS EN 15816:2011EN 15816:2011 (E) 7 d) the test results in accordance with Clause 8; e) the date of the tests. This page deliberately left blankThis p

33、age deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British St

34、andards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions

35、.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside

36、 frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and

37、hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for inter

38、national standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +

39、44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and rece

40、ive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at inf

41、ormation about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduc

42、ed, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: