EN 16066-2011 en Packaging - Rigid plastic containers - PET finish 26 7 (lead 6 35)《包装 刚性塑料容器 宠物完成26日7(6 35岁)》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16066:2011Packaging Rigid plasticcontainers PET finish 26,7(lead 6,35)BS EN 16066:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN

2、 16066:2011.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, Packaging - Plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont

3、ract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 69994 8ICS 55.100Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Co

4、mmittee on 31 January 2012.Amendments issued since publicationDate Text affectedBS EN 16066:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16066 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 26,7 (lead 6,35) Emballage - Rcipients en plastique ri

5、gide - Bague PET 26,7 (pas 6,35) Verpackung - Kunststoffbehltnisse - PET-Verschlussmundstck 26,7 (Gewindesteigung 6,35) This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

6、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official

7、 versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Aus

8、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUR

9、OPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16066:2011: EBS EN 16066:20

10、11EN 16066:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Dimensions .53 Requirements .5Bibliography 7BS EN 16066:2011EN 16066:2011 (E) 3 Foreword This document (EN 16066:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. T

11、his European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the ele

12、ments of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this E

13、uropean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland an

14、d the United Kingdom. BS EN 16066:2011EN 16066:2011 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.23 (2008) 1. Efficient packaging is of great importance for the distribution and the protection of goods.

15、Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. BS EN 16066:2011EN 16066:2011 (E) 5 1 Scope This European Standard specifies the dimensions of the 26,7 mm screw finish with three (3) thread starts and a 17,07 mm height for flat waters and non carbon

16、ated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like b

17、ottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. 2.2 Dimensions of the 3 thread starts 120 apart. 180 of full depth thread per lead R 6,35 thread

18、lead-in R 6,35 thread run-out Lead: 6,35 mm (travel per turn) 2.3 General tolerance for others radii: 0,13 mm 2.4 Weight on height 17,07 mm: 3,42 g (density = 1,335) 3 Requirements The following requirements apply. This finish is a top, side and inside seal finish. This finish shall be smooth and fr

19、ee of any defects that will contribute to leaks. Flash shall not exceed 0,13 mm per side, and shall not be continuous. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface of the finish. Requirements for good cl

20、osure application on finish: 0,13 mm max. out-of-parallel sealing surface with neck support ledge is allowed; an offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in E are to follow uniformly those of T. No

21、 overhang allowed at any point in 360 between F and G. A flash to 0,15 mm maximum step is allowable on one side only. G does not exceed E. BS EN 16066:2011EN 16066:2011 (E) 6 Dimensions in millimetres Key 1 start thread 5 above parting line 2 below parting line 6 thread lead-in 3 thread starts 120 a

22、part 7 thread run-out 4 straight NOTE * = includes ovality. Figure 1 Design and dimensions of the finish BS EN 16066:2011EN 16066:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.23 PET finish 26,7 (lead 6,35) 2008 C.E.T.I.E. : International Technical Centre for Bottling and related Packaging 1

23、12 114 rue La Botie 75008 Paris www.cetie.org This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in

24、 Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax

25、 +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if a

26、nyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7

27、001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of st

28、andards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI

29、will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 89

30、96 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information

31、regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and

32、 copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extra

33、ct may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: