EN 16068-2011 en Packaging - Rigid plastic containers - PET finish 38《包装 硬质材料容器 宠物完成38》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16068:2011Packaging Rigid plasticcontainers PET finish 38BS EN 16068:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16068:2011.

2、The UK participation in its preparation was entrusted to T e c h n i c a l Committee PKW/0/-/10, Packaging - Plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contr

3、act. Users are responsible for its correct application. The British Standards Institution 2012 ISBN 978 0 580 69996 2 ICS 55.100 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strate

4、gy Committee on 31 January 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 16068:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16068 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 38 Emballage - Rcipients en plastique r

5、igide - Bague PET 38 Verpackung - Kunststoffbehltnisse - PET-Verschlussmundstck 38 This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

6、 national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German).

7、A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyp

8、rus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C

9、OMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16068:2011: EBS EN 16068:2011EN 16068:2011 (E) 2 Contents Page F

10、oreword 3Introduction .41 Scope 52 Dimensions .53 Requirements .5Bibliography 7BS EN 16068:2011EN 16068:2011 (E) 3 Foreword This document (EN 16068:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given

11、the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the sub

12、ject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B

13、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 16068:201

14、1EN 16068:2011 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.25 (2009) 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packagi

15、ng can lead to damage or wastage of the contents of the pack. BS EN 16068:2011EN 16068:2011 (E) 5 1 Scope This European Standard specifies the dimensions of the 38 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling a

16、nd filling with introduction of nitrogen (0,7 bar max.). This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper ev

17、ident band will tear but will remain connected to the closure shell. This finish is for non crystallized necks only. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. 2.2 Dimensions of the 3 thread starts 120 apart. 180 of full depth thread per lead R 7,5 thread

18、 lead-in R 7,5 thread run-out Lead: 9 mm (travel per turn) 2.3 General tolerance for other radii: 0,05 mm 2.4 Weight on height 16,5 mm (density = 1,335): Z = 41,0 mm Weight 4,18 g Z = 44,0 mm Weight 4,57 g 3 Requirements The following requirements apply: This finish is a top, side and inside seal fi

19、nish. This finish shall be smooth and free of any defects that will contribute to leaks. Flash shall not exceed 0,13 mm per side, and shall not be continuous. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface

20、 of the finish. Requirements for good closure application on finish: 0,13 mm max. out-of-parallel sealing surface with neck support ledge is allowed; an offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in

21、E are to follow uniformly those of T. In case of usage for a sensitive product, the bottler shall check that the closure is suitable for this usage. BS EN 16068:2011EN 16068:2011 (E) 6 Dimensions in millimetres Key 1 start thread 4 straight 2 radius centre 5 thread lead-in 3 thread starts 120 apart

22、Figure 1 Design and dimensions of the finish BS EN 16068:2011EN 16068:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.25 PET finish 38 2009 C.E.T.I.E. : International Technical Centre for Bottling and related Packaging 112 114 rue La Botie 75008 Paris www.cetie.org This page deliberately left

23、blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Chart

24、er. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment

25、or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards wou

26、ld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service calle

27、d PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addi

28、tion all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant internatio

29、nal standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards d

30、evelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standard

31、s Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the in

32、formation used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any f

33、orm or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: