EN 16081-2011 en Hyperbaric chambers - Specific requirements for fire extinguishing systems - Performance installation and testing (Incorporates Amendment A1 2013)《高压氧舱对消防设施系统的特殊要求.pdf

1、BSI Standards PublicationBS EN 16081:2011+A1:2013BS EN 16081:2011Hyperbaric chambers Specific requirements for fire extinguishing systems Performance, installation and testingEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16081:2011+A1 September 2013 ICS 13.220.20 Supersedes EN 16081:2011 Engl

2、ish Version Hyperbaric chambers - Specific requirements for fire extinguishing systems - Performance, installation and testing Chambres hyperbares - Exigences spcifiques relatives aux systmes de lutte contre lincendie - Performances, installation et essais Druckkammern - Spezifische Anforderungen an

3、 Feuerlschsysteme - Leistung, Montage und Prfung This European Standard was approved by CEN on 8 July 2011 and includes Amendment 1 approved by CEN on 13 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta

4、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engli

5、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B

6、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

7、 Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membe

8、rs. Ref. No. EN 16081:2011+A1:2013: E BS EN 16081:2011+A1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16081:2011+A1:2013. It supersedes BS EN 16081:2011, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in

9、the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by .The UK participation in its preparation was entrusted to Technical Committee CH/100/-/1, Multi-occupancy hyperbaric chambers for use as medical

10、devices.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by B

11、SI Standards Limited 2013ISBN 978 0 580 84509 3ICS 11.040.60; 13.220.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amendments/corrigenda issue

12、d since publicationDate Text affected30 September 2013 Implementation of CEN amendment A1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16081:2011+A1 September 2013 ICS 13.220.20 Supersedes EN 16081:2011 English Version Hyperbaric chambers - Specific requirements for fire extinguishing sy

13、stems - Performance, installation and testing Chambres hyperbares - Exigences spcifiques relatives aux systmes de lutte contre lincendie - Performances, installation et essais Druckkammern - Spezifische Anforderungen an Feuerlschsysteme - Leistung, Montage und Prfung This European Standard was appro

14、ved by CEN on 8 July 2011 and includes Amendment 1 approved by CEN on 13 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

15、and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

16、e responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugos

17、lav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN

18、DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16081:2011+A1:2013: E EN 16081:2011+A1:2013 (E) 2 Contents Page F

19、oreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Specific hazards regarding fire risks .4 5 Performance and requirements 4 6 Test requirements for fire extinguishing systems .6 Annex A (informative) Dummy 10 Annex B (informative) Operation of fire extinguishing systems . 11

20、B.1 Risk analysis and procedures . 11 B.2 Elements of fire fighting . 12 B.3 Prevention . 12 B.3.1 Materials 12 B.3.2 Prohibited materials . 13 B.3.3 Education and training . 14 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 93/42/E

21、EC on Medical Devices“ . 15 Bibliography . 16 EN 16081:2011+A1:2013 (E) 3 Foreword This document (EN 16081:2011+A1:2013) has been prepared by Technical Committee CEN/TC 359 “Project Committee - Hyperbaric chambers”, the secretariat of which is held by DIN. This European Standard shall be given the s

22、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document may be the subj

23、ect of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 16081:2011. This document includes Amendment 1, approved by CEN on 2013-08-13. The start and finish of text introduced or altered by amendment is indicate

24、d in the text by tags !“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral par

25、t of this document. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Ma

26、cedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16081:2011+A1:2013EN 16081:2011+A1:2013 (E)EN 16081:2011+A1:2

27、013 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Specific hazards regarding fire risks .4 5 Performance and requirements 4 6 Test requirements for fire extinguishing systems .6 Annex A (informative) Dummy 10 Annex B (informative) Operation of fire ex

28、tinguishing systems . 11 B.1 Risk analysis and procedures . 11 B.2 Elements of fire fighting . 12 B.3 Prevention . 12 B.3.1 Materials 12 B.3.2 Prohibited materials . 13 B.3.3 Education and training . 14 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirement

29、s of EU Directive 93/42/EEC on Medical Devices“ . 15 Bibliography . 16 EN 16081:2011+A1:2013 (E) 3 Foreword This document (EN 16081:2011+A1:2013) has been prepared by Technical Committee CEN/TC 359 “Project Committee - Hyperbaric chambers”, the secretariat of which is held by DIN. This European Stan

30、dard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this

31、 document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 16081:2011. This document includes Amendment 1, approved by CEN on 2013-08-13. The start and finish of text introduced or altered

32、 by amendment is indicated in the text by tags !“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA,

33、 which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme

34、r Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16081:2011+A1:2013EN 16081:2011+A1:2

35、013 (E)EN 16081:2011+A1:2013 (E) 4 1 Scope This European Standard is applicable to the performance and safety requirements of fire extinguishing systems and their associated test methods for multi-place chambers designed for pressures in excess of ambient atmospheric pressure and employed in medical

36、 installations for therapeutic purposes, in the following referred to as chambers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the

37、 referenced document (including any amendments) applies. EN 14931:2006, Pressure vessels for human occupancy (PVHO) Multi-place pressure chamber systems for hyperbaric therapy Performance, safety requirements and testing 3 Terms and definitions For the purposes of this document, the following terms

38、and definitions apply: 3.1 fire extinguishing system system for active deployment of extinguishing medium inside the chamber in order to extinguish fire 3.2 extinguishing medium liquid or gas used to extinguish fire 3.3 nozzle mechanical device used to ensure dispersion of extinguishing medium insid

39、e the chamber with certain characteristics 4 Specific hazards regarding fire risks A fire, as a physical phenomenon, is significantly influenced by the ambient pressure, the partial pressure of oxygen and the confined space of the hyperbaric chamber. The rate of combustion will be directly related t

40、o ambient pressure and the oxygen level. In a hyperbaric environment with increased oxygen partial pressure, even materials thought to be non-combustible will burn fiercely. Owing to the confined space in the chamber, a fire would cause a sudden increase of temperature and high concentration of toxi

41、c gases and smoke. If such a fire occurs, it shall be dealt with quickly and all personnel and patients shall be evacuated from the chamber. People suffering from breathing difficulties and burns shall be cared for (see Annex B). 5 Performance and requirements 5.1 Fire extinguishing systems in hyper

42、baric chambers shall produce a specified extinguishing performance as stated in Clause 6. 5.2 Fire extinguishing systems shall suit the chambers maximum operational pressure. They shall fully protect all chamber compartments for human occupancy. EN 16081:2011+A1:2013 (E) 5 5.3 The fire extinguishing

43、 system shall be installed in such a way that the risk of physical injury to persons inside the chamber is as low as possible. 5.4 Fire extinguishing systems shall have a manual release. Independent activation shall be possible from inside and outside the chamber. The release shall be easily accessi

44、ble and protected against unintentional activation (e.g. safety button). For operation, see EN 14931:2006, 4.5.1. An additional automatic release is permitted if its suitability is proven for hyperbaric conditions up to the chambers maximum operational pressure and documented. 5.5 With both an autom

45、atic and manual release, a warning signal shall be heard at the control console. This warning signal may be temporarily muted, but there shall be no possibility to switch it off as long as the fire system is active. 5.6 The extinguishing nozzles shall be installed in such a way that the required ext

46、inguishing effect is ensured for any sitting and lying place inside the chamber. A lying place is to be considered as minimum three sitting places in one line. NOTE The nozzles arrangement is stipulated by the manufacturer of the fire extinguishing system. He decides where and how many nozzles in ac

47、cordance with seats or stretchers are to be placed. Other areas shall be covered in the seating height by the equivalent of at least 50% of the required extinguishing medium flow specified per seat (see 6.2.14). This medium flow shall be delivered from nozzles of the same characteristic as in the te

48、st. 5.7 Pipes and hoses containing the extinguishing medium shall be made of suitable material concerning pressure and corrosion. For other pipes and hoses, see EN 14931:2006, 4.7.4. For shut off devices, see EN 14931:2006, 4.2.15 5.8 Pipes and hoses of the fire extinguishing system shall be marked

49、according to the medium and its function. Actuators (e.g. valves, press buttons and manual releases) shall be marked in such a way that they are distinguished from all other systems. For installation of pipes, see EN 14931:2006, 4.7.7. 5.9 The extinguishing medium tank shall be suitable for the intended pressure and protected against pressure exceeding the maximum allowable design pressure. The material of the tank shall be suitable for the extinguishing medium or shall be adequately protected against corrosion. The extinguishing medium supply tank