EN 16592-2014 en Packaging - Rigid plastic containers - PET finish 29 25 (12 6)《包装 硬质塑料容器 聚对苯二甲酸乙二醇酯完成29 25(12 6)》.pdf

1、BSI Standards PublicationBS EN 16592:2014Packaging Rigid plasticcontainers PET finish 29/25(12,6)BS EN 16592:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16592:2014.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, P

2、ackaging - Plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Publi

3、shed by BSI StandardsLimited 2014ISBN 978 0 580 82401 2ICS 55.100Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2014.Amendments issued since publicati

4、onDate Text affectedBS EN 16592:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16592 October 2014 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 29/25 (12,6) Emballage - Rcipients en plastique rigide - Bague PET 29/25 (12,6) Verpackung - Formstabile Kunststoff

5、behlter - PET-Verschlussmundstck 29/25 (12,6) This European Standard was approved by CEN on 6 September 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter

6、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made

7、 by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni

8、a, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDA

9、RDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16592:2014 EBS EN 16592:2014EN 16592:2014

10、 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Dimensions .5 3 Requirements .5 Bibliography 9 BS EN 16592:2014EN 16592:2014 (E) 3 Foreword This document (EN 16592:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This Europ

11、ean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the latest by April 2015. Attention is drawn to the possibility that some of the elements

12、 of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europe

13、an Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove

14、nia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16592:2014EN 16592:2014 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.26 (2009) 1. Efficient packaging is of great importance for the

15、distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. BS EN 16592:2014EN 16592:2014 (E) 5 1 Scope This European Standard specifies the design and dimensions of the 29 mm screw finish with three (3) thread starts f

16、or flat waters and non-carbonated beverages. This finish is designated PET finish 29/25 (12,6). This finish can be used for aseptic filling and filling with nitrogen charge (internal overpressure inferior to 1 bar max). The dimension (12,6) is the height in millimetres from the top of finish to the

17、bottom of the support ledge. This finish is designed to accept a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and remain on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but

18、 will remain connected to the closure shell. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. Dimensions are those of the preform. 2.2 Dimensions of the 3 thread starts 120 apart: 180 of full thread per lead: R 6,25 mm thread run-in; R 6,25 mm thread run-out. L

19、ead: 6,5 mm (travel per turn). 2.3 General tolerance for others radii: 0,13 mm. 2.4 Weight on height 12,6 mm: 2,41 g (density = 1,335 g/cm3). 3 Requirements This finish is a top, side and inside seal finish. This finish shall be smooth and free of any defects that will contribute to leaks. Flash not

20、 to exceed 0,13 mm per side, and not to be continuous. The diameter under the support ledge shown at 28,00 mm refers to the preform and should be at 28,50 maximum on the blown bottle. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and a

21、cross the sealing surface of the finish. Requirements for good closure application on finish: 0,13 mm max out-of-parallel sealing surface with neck support ledge is allowed. An offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. Variations in E are to follow uniformly t

22、hose of T. BS EN 16592:2014EN 16592:2014 (E) 6 No overhang allowed at any point in 360 between F and G. A flash to 0,15 mm maximum step is allowable on one side only. G does not exceed E. The success of the capping operation requires a correct adjustment and good conditions of maintenance of the cap

23、ping equipment. BS EN 16592:2014EN 16592:2014 (E) 7 Dimensions in millimetres BS EN 16592:2014EN 16592:2014 (E) 8 Key X height from top of finish to bottom of support ledge P thread pitch T thread crest diameter H clearance height required for proper closure function E thread root diameter Z maximum

24、 diameter on support ledge G lower ring diameter A tamper evident bead diameter C control diameter at top of finish B tamper evident band recess diameter S height from top of finish to start of full depth of thread PL parting line INT PT intersection point F upper ring diameter 1 thread run-in 2 thr

25、ead run-out Figure 1 Design and dimensions of the finish BS EN 16592:2014EN 16592:2014 (E) 9 Bibliography 1 CE. T.I.E. data sheet GME 30.26 - PET finish 29/25 (12,6) - 20091)1) Obtainable through Centre Technique International de lEmbouteillage et du Conditionnement (CE.T.I.E), 112- 114, rue La Boti

26、e, 75008 Paris, France, www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is inco

27、rporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and o

28、thers to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to

29、help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download

30、 PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our

31、Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and internatio

32、nal standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing

33、 Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Networ

34、k Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and

35、other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, softw

36、are and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for

37、commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Deta

38、ils and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW