EN 16722-2015 en Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends《工业阀门 端口到端口和中心到端口维度的螺纹末端阀门》.pdf

1、BSI Standards PublicationBS EN 16722:2015Industrial valves End-to-endand centre-to-end dimensionsfor valves with threaded endsBS EN 16722:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16722:2015.The UK participation in its preparation was entrusted to Tec

2、hnicalCommittee PSE/18/1, Industrial valves, steam traps, actuators andsafety devices against excessive pressure - Valves - Basic standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryp

3、rovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 85597 9ICS 23.060.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publis

4、hed under the authority of theStandards Policy and Strategy Committee on 31 October 2015.Amendments/corrigenda issued since publicationDateT e x t a f f e c t e dBS EN 16722:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16722 September 2015 ICS 23.060.01 English Version Industrial valves

5、- End-to-end and centre-to-end dimensions for valves with threaded ends Robinetterie industrielle - Dimensions extrmit extrmit et axe extrmit pour les appareils de robinetterie embouts filets Industriearmaturen - Baulngen fr Armaturen mit Innengewinde-Anschluss This European Standard was approved by

6、 CEN on 15 August 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standa

7、rds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and not

8、ified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, I

9、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Man

10、agement Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16722:2015 EBS EN 16722:2015EN 16722:2015 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative referen

11、ces 5 3 Terms and definitions . 5 4 Dimensions and tolerances . 6 4.1 Basic series 6 4.2 Tolerances . 7 Annex A (informative) Relationship between DN (nominal size) and internal thread 16 Annex B (informative) Origin of basic series 17 Annex C (informative) Relationship between DN (nominal size) and

12、 nominal pipe size (NPS) . 18 Bibliography . 19 BS EN 16722:2015EN 16722:2015 (E) 3 European foreword This document (EN 16722:2015) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a

13、 national standard, either by publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of pat

14、ent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cr

15、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

16、 the United Kingdom. BS EN 16722:2015EN 16722:2015 (E) 4 Introduction The basic series given in this European Standard are taken from the original series shown in Annex B. Changes made to the original series will not be automatically incorporated into this European Standard. BS EN 16722:2015EN 16722

17、:2015 (E) 5 1 Scope This European Standard specifies the end-to-end and centre-to-end dimensions for valves with threaded ends with connecting dimensions in compliance with EN ISO 228-1 or EN 10226-1, used in PN and Class designated piping systems. The range of PN is: PN 10; PN 16; PN 25; PN 40; PN

18、63; PN 100; PN 160; PN 250; PN 320; PN 400. The range of Class is: Class 150, Class 300, Class 600, Class 900, Class 1 500, Class 2 500. The range of nominal size is: DN 4; DN 6; DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100. NOTE 1 See Annex C for the relationship betw

19、een nominal size (DN) and nominal pipe size (NPS). NOTE 2 Valves having screwed end profiles different from those specified in EN ISO 228-1 or EN 102261, may use the same dimensions than those specified in Table 1. 2 Normative references The following documents, in whole or in part, are normatively

20、referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 736-1:1995, Valves Terminology Part 1: Definition of types of valv

21、es EN 736-2:1997, Valves Terminology Part 2: Definition of components of valves EN 736-3:2008, Valves Terminology Part 3: Definition of terms 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1:1995, EN 736-2:1997 and EN 736-3:2008 and the following

22、 apply. 3.1 end-to-end dimensions (ETE) (straight pattern valves) distance expressed between the ends of the body for straight and oblique pattern valves 3.2 centre-to-end dimensions (CTE) (angle pattern valves) distance expressed between one of the ends of the body and the centre of the body for an

23、gle pattern valves 3.3 end-to-end and centre-to-end dimensions (ETE+CTE) (three-way valves) distance expressed between the ends of the body (ETE) in the run and distance expressed between the end of the body in the branch and the centre of the body (CTE) BS EN 16722:2015EN 16722:2015 (E) 6 a) Straig

24、ht and oblique pattern valve b) Angle pattern valve c) Three-way valve Key Figure 1 a) ETE with ETE = l Figure 1 b) CTE with CTE = l Figure 1 c) ETE+CTE with ETE = l and CTE = l / 2 Figure 1 ETE and CTE dimensions 4 Dimensions and tolerances 4.1 Basic series The basic series of l for ETE and CTE dim

25、ensions are given in Table 1. For each type of valve, the basic series to be taken into consideration shall be in accordance with Tables 3 to 7. Other dimensions are subject of agreement between manufacturer and purchaser. BS EN 16722:2015EN 16722:2015 (E) 7 NOTE 1 Table 1 gives complete series. In

26、Tables 3 to 7 the columns of series may be reduced. NOTE 2 For certain sizes/types of valves, alternative dimensions are permitted and are specified in Tables 3 to 7. 4.2 Tolerances Tolerances on ETE and CTE dimensions shall be in accordance with Table 2. BS EN 16722:2015BS EN 16722:2015EN 16722:201

27、5 (E) 8 Table 1 Dimensions l of basic series Dimensions in millimetres DN Basic series M2 M3 M4 M5 X1 X2 X3 X4 X5 X6 X7 X8 X9 X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X20 4 50 70 50 69 69 69 6 50 70 50 69 69 69 85 8 55 70 55 70 65 78 69 69 85 55 67 75 10 70 60 75 55 95 70 65 78 55 73 73 72 85 55 67 7

28、5 15 85 75 85 65 95 49 200 70 65 90 65 117 104 84 95 65 75 90 20 100 80 95 75 95 49 200 80 65 95 80 117 104 96 97 95 100 95 70 90 105 25 115 90 105 90 95 61 200 90 139 104 113 113 113 120 110 95 65 80 85 105 120 32 130 110 120 95 95 61 200 186 110 115 110 120 130 65 80 95 120 40 150 120 130 100 130

29、72 255 186 120 135 130 140 145 165 70 87 105 135 50 180 140 150 112 230 72 255 209 140 140 140 150 160 165 70 91 125 155 65 185 185 132 167 190 80 205 205 160 192 205 100 240 240 180 230 BS EN 16722:2015BS EN 16722:2015EN 16722:2015 (E) 9 Table 1 (continued) Dimensions in millimetres DN Basic series

30、 X21 X22 X23 X24 X25 X26 X27 X28 X29 X30 4 6 8 70 72 42 10 70 72 75 49 60 59 83 105 15 75 82 75 85 56 65 74 90 90 114 20 85 92 75 100 61 78 80 97 100 125 25 102 102 75 115 69 92 91 110 115 142 32 118 118 130 77 105 110 124 134 160 40 125 134 150 81 120 120 130 150 170 50 149 144 180 95 145 141 155 1

31、68 200 65 170 112 80 220 122 100 160 BS EN 16722:201510 Table 2 Tolerances Dimensions in millimetres Dimension ETE or CTE aTolerance above up to andincluding 0 250 2 250 500 3 500 800 4 800 1 000 5 1 000 1 600 6 1 600 2 500 8 aDimensions ETE or CTE in accordance with Figure 1. BS EN 16722:2015EN 167

32、22:2015 (E) BS EN 16722:201511 Table 3 Gate valves PN/Class ETE series CTE series M2 M4 X13 X14 X16aX17 X25 X26 X27 X28 X29 X30 PN 10 to PN 16 x x x x x x x x x x x x PN 25 to PN 40 PN 63 to PN 100 PN 160 PN 250 to PN 320 PN 400 Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500 aThe di

33、mensions in column X16 of Table 1 refer to the horizontal dimensions of a vertical gate valve type. BS EN 16722:2015EN 16722:2015 (E) BS EN 16722:201512 Table 4 Ball valves PN/Class ETE series M2 M4 X10 X11 X12 X13 X14 X18aX19aX20aX21aX22aX24 X25 X26 X27 X28 X29 X30 PN 10 to PN 16 x x x x x x x x x

34、x x x x x x x x X PN 25 to PN 40 x x x x x x x x x x x x x x x x x x x PN 63 to PN 100 x x x x x x x x x x PN 160 x x x x x x PN 250 to PN 320 x x x x x x PN 400 x x x x x Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500 aAdditional ETE+CTE series for three-way valves BS EN 16722:2015

35、EN 16722:2015 (E) BS EN 16722:201513 Table 5 Globe valves and lift check valves; straight and oblique patterns PN/Class ETE series X1 X2 X8 X9 X25 X26 X27 X28 X29 X30 M3 M4 M5PN 10 to PN 16 x x x x x x x x x x x x x PN 25 to PN 40 x x x x x x x x x x x x PN 63 to PN 100 PN 160 PN 250 to PN 320 PN 40

36、0 Class 150 x x x x x x x x x x x x x Class 300 x x x x x x Class 600 Class 900 Class 1 500 Class 2 500 BS EN 16722:2015EN 16722:2015 (E) BS EN 16722:201514 Table 6 Globe control valves; straight pattern PN/Class ETE series X8 M3 M4 M5 PN 10 to PN 16 x x x x PN 25 to PN 40 x x x x PN 63 to PN 100 PN

37、 160 PN 250 to PN 320 PN 400 Class 150 x x x x Class 300 x x x x Class 600 Class 900 Class 1 500 Class 2 500 BS EN 16722:2015EN 16722:2015 (E) BS EN 16722:201515 Table 7 Automatic steam traps PN/Class ETE series X1 X2 X3 X4 X5 X6 X7 X8 X9 X15 X23 M3 M4 M5PN 10 to PN 16 x x x x x x x x x x x x x x PN

38、 25 to PN 40 x x x x x x x x x x x x x PN 63 to PN 100 x x x PN 160 PN 250 to PN 320 PN 400 Class 150 x x x x x x x x x x x x x x Class 300 x x x x x x x x x x x x x Class 600 x x x Class 900 Class 1 500 Class 2 500 BS EN 16722:2015EN 16722:2015 (E) BS EN 16722:2015EN 16722:2015 (E) 16 Annex A (info

39、rmative) Relationship between DN (nominal size) and internal thread For the relationship between DN and internal thread, see Table A.1. Table A.1 Relationship between DN and internal thread DN EN 102261 EN ISO 228-1 ASME B1.20.1 6 Rp G NPT 8 Rp G NPT 10 Rp G NPT 15 Rp G NPT 20 Rp G NPT 25 Rp 1 G 1 N

40、PT 1 32 Rp 1 G 1 NPT 1 40 Rp 1 G 1 NPT 1 50 Rp 2 G 2 NPT 2 65 Rp 2 G 2 NPT 2 80 Rp 3 G 3 NPT 3 100 Rp 4 G 4 NPT 4 BS EN 16722:2015EN 16722:2015 (E) 17 Annex B (informative) Origin of basic series For origins of basic series, see Table B.1. Table B.1 Origin of basic series Basic series Origin M2- M5

41、DIN 32024:1982 X1 X30 According to agreements between and proposals of CEN/TC 69 experts involved in the preparation of this European Standard BS EN 16722:2015EN 16722:2015 (E) 18 Annex C (informative) Relationship between DN (nominal size) and nominal pipe size (NPS) For the relationship between DN

42、 (nominal size) and nominal pipe size (NPS) see Table C.1. Table C.1 Relationship between DN (nominal size) and nominal pipe size (NPS) Nominal size DN 6 8 10 15 20 25 32 40 50 65 80 100 NPS 1/8 1/4 3/8 1/2 3/4 1 1 1 2 2 3 4 BS EN 16722:2015EN 16722:2015 (E) 19 Bibliography 1 EN 558, Industrial valv

43、es Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves 2 EN 10226-1, Pipe threads where pressure tight joints are made on the threads Part 1: Taper external threads and parallel internal threads Dimensions, tolerances and designat

44、ion 3 EN 12516-1, Industrial valves Shell design strength Part 1: Tabulation method for steel valve shells 4 EN 12627, Industrial valves Butt welding ends for steel valves 5 EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) 6 DIN 3202-4:1982, Face-to-face and centre-to-face dimensions of valves Valves with female thread connection 7 ASME B16.10,