EN 16948-2017 en Child protective products - Consumer fitted child resistant locking devices for cupboards and drawers - Safety requirements and test methods.pdf

1、Child protective products - Consumer fitted child resistant locking devices for cupboards and drawers - Safety requirements and test methodsBS EN 16948:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16948 July

2、 2017 ICS 97.140 English Version Child protective products - Consumer fitted child resistant locking devices for cupboards and drawers - Safety requirements and test methods Articles pour la scurit des enfants - Dispositifs de fermeture monter soi-mme rsistants aux enfants pour les armoires et les t

3、iroirs - Exigences de scurit et mthodes dessai Kindersicherheitsprodukte - Vom Verbraucher angebrachte kindergesicherte Verriegelungsvorrichtungen fr Schrnke und Schubladen - Sicherheitsanforderungen und Prfverfahren This European Standard was approved by CEN on 10 April 2017. CEN members are bound

4、to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-

5、CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has

6、 the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux

7、embourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1

8、000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16948:2017 ENational forewordThis British Standard is the UK implementation of EN 16948:2017.The UK participation in its preparation was entrusted to Technical Commi

9、ttee B/538/4/15, Finger traps.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institutio

10、n 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 91977 0ICS 97.140Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigend

11、a issued since publicationDate Text affectedBRITISH STANDARDBS EN 16948:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16948 July 2017 ICS 97.140 English Version Child protective products - Consumer fitted child resistant locking devices for cupboards and drawers - Safety requirements and

12、test methods Articles pour la scurit des enfants - Dispositifs de fermeture monter soi-mme rsistants aux enfants pour les armoires et les tiroirs - Exigences de scurit et mthodes dessai Kindersicherheitsprodukte - Vom Verbraucher angebrachte kindergesicherte Verriegelungsvorrichtungen fr Schrnke und

13、 Schubladen - Sicherheitsanforderungen und Prfverfahren This European Standard was approved by CEN on 10 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an

14、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langua

15、ge made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,

16、 Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMI

17、TTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16948:2017 EBS EN 16948:20

18、17EN 16948:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and Definitions . 4 4 Requirements . 4 4.1 Child appeal . 4 4.2 Child protective function 4 4.2.1 General 4 4.2.2 Requirements concerning the child panel test . 5 4.3 Mechanical function and structur

19、al integrity . 7 4.4 Small parts . 8 4.5 Sharp edges . 8 4.6 Purchase information 8 4.7 User instructions . 8 4.8 Marking of the product . 9 5 Test methods 9 5.1 General test conditions . 9 5.2 Test equipment 9 5.2.1 A test rig for the child panel test 9 5.2.2 Test rig for mechanical tests . 9 5.2.3

20、 Equipment to perform cyclic opening, loading and closing operations for the wear testing . 11 5.2.4 Probe. 12 5.2.5 Small parts cylinder 12 5.2.6 Tension test equipment . 12 5.3 Extent and order of testing . 13 5.4 Test procedures - child protective function . 13 5.4.1 Test supervision . 13 5.4.2 T

21、est samples 13 5.4.3 Preliminary checking and preparation 13 5.4.4 Child test 14 5.5 Test procedure mechanical tests 15 5.5.1 Test of durability of the locking device and the locking mechanism 15 5.5.2 Test of disengagement force of locking mechanism using a single operation . 15 5.5.3 Test of disen

22、gagement force of locking mechanism depending on two actions . 15 5.5.4 Test of structural integrity . 16 5.5.5 Opening gap measurement . 16 5.5.6 Small parts test . 16 5.6 Test report 17 Annex A (normative) Flowchart of test procedure . 19 Annex B (informative) Rationales . 20 Bibliography . 22 BS

23、EN 16948:2017EN 16948:2017 (E) 3 European foreword This document (EN 16948:2017) has been prepared by Technical Committee CEN/TC 398 “Child protective products”, the secretariat of which is held by ASI. This European Standard shall be given the status of a national standard, either by publication of

24、 an identical text or by endorsement, at the latest by January 2018, and conflicting national standards shall be withdrawn at the latest by January 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held respon

25、sible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finlan

26、d, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16948:2017EN 16948:2

27、017 (E) 4 1 Scope This European Standard specifies requirements and test methods for locking devices fitted by consumers in a domestic environment for cupboards and drawers for restricting access by young children. Child resistant locking devices only intended to be installed by professionals or tha

28、t are an integral part of the cupboard and drawer system are beyond the scope of this standard. 2 Normative references Not applicable. 3 Terms and Definitions For the purposes of this document, the following terms and definitions apply. 3.1 child protective locking device for cupboards and drawers l

29、ocking device device mounted on cupboards and drawers intended to make it difficult for young children to access the contents of the cupboard/drawer Note 1 to entry: In the remainder of the document the short expression “locking device” is used for “child protective locking device for cupboards and

30、drawers” 3.2 locking mechanism part of the locking device which prevents opening of the cupboard or drawer 3.3 child appealing locking device locking device that resembles by any means another object commonly recognized as appealing to or intended for use by young children, or has entertaining audio

31、 effects or animated effects Note 1 to entry: This includes, but is not limited to locking devices the shape of which resembles cartoon characters, toys, guns, watches, telephones, musical instruments, vehicles, human body or parts of the human body, animals, food or beverages, or that play musical

32、notes, or have flashing lights or moving objects or other entertaining features. 4 Requirements 4.1 Child appeal The locking device shall not be child appealing. 4.2 Child protective function 4.2.1 General The locking mechanism shall be resistant to operation by young children. It shall either: a) r

33、equire one action and not release the locking mechanism when tested in accordance with 5.5.2; or BS EN 16948:2017EN 16948:2017 (E) 5 b) require at least two consecutive actions to release the locking mechanism, the operation of the second action being dependent on the first action having been carrie

34、d out and maintained and not release the locking mechanism when tested in accordance with 5.5.3; or c) require at least two separate but simultaneous actions to release the locking mechanism operating on different principles and not release the locking mechanism when tested in accordance with 5.5.3;

35、 or d) require the use of a specifically designed removable device or removable tool (e.g. a key or a magnet); or e) comply with the child panel test requirements in 4.2.2. Ideally, the locking mechanism would automatically re-engage when closing the cupboard or drawer after having been completely d

36、isengaged. However, at this point in time this is not a requirement. It may become a requirement in future. In b) maintaining or removing the first action cannot mean that the locking mechanism remains in the partially unlocked position without continued intervention of the user. 4.2.2 Requirements

37、concerning the child panel test 4.2.2.1 General The locking mechanism shall comply with either 4.2.2.2 or 4.2.2.3. The child panel test is required only in case option 4.2.1 e) is chosen. The minimum number of children required in the sequential test depends on how many children can open the locking

38、 mechanism. The number to pass a locking device can be as low as 30. 4.2.2.2 Test panel of 200 children If the full test panel of 200 children is used when testing in accordance with 5.4, the following requirements shall be met: a) at least 85 % of the children in the test panel shall be unable to d

39、isengage the locking mechanism within the first 5 min without a demonstration; and b) at least 80 % of the children in the test panel shall be unable to disengage the locking mechanism within another 5 min after a demonstration has been given to those children unable to disengage the locking mechani

40、sm in the first 5 min. 4.2.2.3 Sequential test less than 200 children If the full test panel is not used when testing in accordance with 5.4, the result is obtained from completing Figure 1 and Figure 2 as follows: a) the result of the test is a failure if the child succeeds in disengaging the locki

41、ng mechanism; b) as each result is obtained, it shall be plotted on the appropriate chart by filling in a square as follows: 1) fill in a square immediately to the right of the previous result on Figure 1 if the child failed to disengage the locking mechanism in the first 5 min, and on Figure 2 if t

42、he child failed to disengage the locking mechanism in the second 5 min, i.e. if the result is a success; 2) fill in a square immediately above the previous result on Figure 1 and Figure 2 if the child succeeded in disengaging the locking mechanism in the first 5 min, or only on Figure 2 if the child

43、 succeeded in disengaging the locking mechanism in the second 5 min, i.e. if the result is a failure. BS EN 16948:2017EN 16948:2017 (E) 6 In the case of the first result to be plotted, the blanked out square is regarded as the “previous result”. The locking device shall be deemed to have: passed the

44、 test as soon as the trail of filled squares passes below limit line 1 on both Figure 1 and Figure 2; failed the test as soon as the trail of filled squares passes above limit line 2 on either Figure 1 or Figure 2. If neither occurs, the results shall be assessed in accordance with the requirements

45、laid down in 4.2.2.2. Key 1 number of locking mechanism not disengaged 4 limit line 2 2 number of locking mechanism disengaged 5 limit line 1 3 enlargement of chart scale Acceptable quality limit (AQL) = 5 %; limiting quality (LQ): 20 %; = = 5 %, where is the producers risk; is the consumers risk. F

46、igure 1 Chart of a sequential child test procedure (before demonstration) for locking mechanism BS EN 16948:2017EN 16948:2017 (E) 7 Key 1 number of locking mechanism not disengaged 3 limit line 2 2 number of locking mechanism disengaged 4 limit line 1 Acceptable quality limit (AQL) = 5 %; limiting q

47、uality (LQ): 20 %; = = 5 %, where is the producers risk; is the consumers risk. NOTE For an enlargement of the chart scale, see Figure 1. Figure 2 Chart of a sequential child test procedure (after demonstration) for locking mechanism 4.2.2.4 Full test If a sequential procedure is not used and the fu

48、ll number of children is tested, the results shall be assessed in accordance with the requirements laid down in 4.2.2.2. 4.2.2.5 Additional information to be recorded Any other information deemed to be useful in assessing the interpretation of the result, such as the time required for children to di

49、sengage the locking mechanism and, where appropriate, to engage it properly, the method used by children to disengage it, etc. shall be recorded. 4.3 Mechanical function and structural integrity The locking device shall maintain its mechanical properties throughout its expected lifetime. The manufacturer shall indicate the type(s) of cupboards and drawers including the materials (e.g. glass, aluminium, PVC, wood) for which the locking device is or is not suitable. In particular, if fixings (e.g. screws) are provided