EN 22872-1992 en Packaging - Complete Filled Transport Packages - Compression Test《包装 完整满装运输包装 加压试验》.pdf

1、CEN EN*22872 92 3404589 004032b 720 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 22872 November 1992 UDC 621.798.1:620.173 Descriptors: Packing, transport packing, complete- and filled packages, impact tests, drop tests English version Packaging - Complete, filled transport packages - Compre

2、ssion test (IS0 2872 : 1985) Emballages - Emballages dexpdition complets et pleins - Essai de compression (IS0 2872 : 1985) Verpackung - Versandfertige Packstcke Stauchprfung (IS0 2872 : 1985) This European Standard was approved by CEN on 1992-10-30. CEN members are bound to comply with the CEN/CENE

3、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any C

4、EN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN

5、members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europ

6、isches Komitee fr Normung Central Secretariat: rue de Stassart 36, B- 1050 Brussels O 1992 Copyright reserved to CEN members Ref. No. EN 22872 : 1992 E CEN ENa22872 92 M 3404589 0040327 bb7 M Page 2 EN 22872 : 1992 Foreword In 1991, IS0 2872 : 1985 Packaging - Complete, filled transport packages - C

7、ompression test was submitted to the CEN Primary Questionnaire procedure. Following the positive result of the CEN/CS Proposal IS0 2872 : 1985 was submitted to the Formal Vote. The result of the Formal Vote was positive. This European Standard shall be given the status of a national standard, either

8、 by publication of an identical text or by endorsement, at the latest by May 1993, and conflicting national standards shall be withdrawn at the latest by May 1993. According to the CENXENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgiu

9、m, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN EN*22872 72 I 3404587 OQY0328 5T3 Page 3 EN 22872 : 1992 Packaging - Complete, filled transport packages - Compression test 1 Scope and

10、 field of application This International Standard specifies two methods for testing complete, filled transport packages for compression resistance. The test may be used to assess the performance of a package in terms of its strength or of the protection it offers to its contents when it is subjected

11、 to compressive forces. It may be per- formed either as a single test to investigate the effects (defor- mation, collapse or failure) of compression or as part of a se- quence of tests designed to measure the ability of a package to withstand a distribution system that includes a compression hazard.

12、 NOTE - A test method using a compression tester to determine the stacking resistance of a package is given in IS0 2874. 2 References IS0 2206, Packaging - Complete, filled transport packages - Identification of parts when testing. IS0 2233, Packaging - Complete, filled transport packages - Conditio

13、ning for testing. IS0 2874, Packaging - Complete, filled transport packages - Stacking test using compression tester. 3 Principle Placing of the test package between the platens of a compres- sion tester, and compression, the load and platen displacement being recorded until failure occurs or predet

14、ermined values for load or displacement are reached. 4 Apparatus 4.1 Compression tester, motor-driven, mechanical or hydraulic, platen-type, capable of applying load through uniform movement of one or both platens at a relative speed of 10 f 3 mm/min. The platens shall be - flat, so that when placed

15、 horizontally the difference in height between the lowest and highest points does not ex- ceed 1 mm; - dimensioned so as to extend over the whole area of the panels with which they are in contact; - rigid, so as not to deform by more than 1 mm at any point when the tester applies a load of 75 % of i

16、ts maximum rating, either to a centrally placed 100 mm x 100 mm x 100 mm block having sufficient strength to accept this load without failure, or to four similar blocks placed at the four corners, in the case of swivel-mounted platens. One platen shall remain horizontal, within two parts per 1 o00 a

17、t all times during the test. The other platen shall be either rigidly mounted so as to remain horizontal within two parts per 1 O00 at all times during the test, or be held by a universal joint at its centre and so be free to tilt in any direction. The working surfaces of platens suitable for testin

18、g packages with a length or width or diameter greater than 1 o00 mm may be locally recessed for fixing bolts, etc. 4.2 Recording device or other means of measurement, with a percentage of error for loads not exceeding f 2 % of the load and an accuracy of platen displacement of f 1 mm. 5 -Package pre

19、paration The test package shall normally be filled with its intended con- tents. However, simulated or dummy contents may be used, on condition that the dimensions and physical properties of such contents shall be as close as possible to those of the in- tended contents. Ensure that the test package

20、 is closed normally, as if ready for distribution. If simulated or dummy contents are used, ensure that the normal method of closure is still employed. 6 Conditioning The package shall be conditioned in accordance with one of the conditions described in IS0 2233. 7 Procedure Whenever possible the te

21、st shall be carried out in the same at- mospheric conditions as used for conditioning, where this is critical to the materials or application of the package. In other circumstances, the test shall be carried out in atmospheric con- ditions which are as near as practicable to those used for con- diti

22、oning. CEN EN*E!2872 92 m 3404589 0040329 43T = Page 4 EN 22872 : 1992 7.1 Method 1 7.1.1 Place the test package centrally on the lower platen of the test machine (4.11, in the predetermined attitude. 7.1.2 Apply the load by relative movement of the platens at 10 f 3 rnm/min until the predetermined

23、value is reached or until premature collapse. In measuring deformation, the datum zero point shall be taken as the reading corresponding to a load of 220 N. 7.2 Method 2 Where it is desired to measure the ability of a complete, filled transport package to resist external compressive loads applied to

24、 opposite edges or corners of the package, the procedure is the same as in Method 1, but it is essential to use a tester in which the platens are not free to tilt. 8 Test report The test report shall include the following particulars : a) reference to this International Standard; b number of replica

25、te packages tested; c) full description of the package, including dimensions, structural and material specifications of the package and its fittings, cushioning, blocking, closure or reinforcing ar- rangements; d) description of contents - if simulated or dummy con- tents were used, full details sha

26、ll be given; e) gross mass of the package and mass of contents, in kilograms; f) relative humidity, temperature and time of conditioning; temperature and relative humidity of test area at time of test; whether these values comply with the requirements of IS0 2233; g) the attitude in which the packag

27、e was tested, using the method of identification given in IS0 2206; h) load imposed, in newtons, and the duration of time of the package under load; j) location of points on packages and stage of test at which measurements were made; k) type of apparatus used, including whether the tester was mechan

28、ically or hydraulically operated and whether or not both platens were rigidly mounted; m) any deviations from the test methods described in this International Standard; n) a record of the result, including load/platen displace- ment recording, with any observations which may assist in correct interpretation: p) date of the test; q) signature of tester.