EN 50090-5-3-2016 en Home and Building Electronic Systems (HBES) - Part 5-3 Media and media dependent layers - Radio Frequency for HBES Class 1.pdf

1、BSI Standards PublicationBS EN 50090-5-3:2016Home and Building ElectronicSystems (HBES)Part 5-3: Media and media dependentlayers Radio Frequency for HBES Class 1BS EN 50090-5-3:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 50090-5-3:2016. It supersedes BS

2、 EN 50090-5-3:2006 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee IST/6/-/12, Home Electronic Systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all th

3、e necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 91842 1 ICS 97.120 Compliance with a British Standard cannot confer immunity from legal obligations.This British Stand

4、ard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 50090-5-3:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50090-5-3 January 2016 ICS 97.120 Supersedes EN

5、50090-5-3:2006 English Version Home and Building Electronic Systems (HBES) - Part 5-3: Media and media dependent layers - Radio Frequency for HBES Class 1 Systmes lectroniques pour les foyers domestiques et les btiments (HBES) - Partie 5-3: Mdias et couches dpendantes des mdias - Radio Frquence pour

6、 HBES Classe 1 Elektrische Systemtechnik fr Heim und Gebude (ESHG) - Teil 5-3: Medien und medienabhngige Schichten - Signalbertragung ber Funk fr ESHG Klasse 1 This European Standard was approved by CENELEC on 2015-11-02. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations

7、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.

8、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

9、ENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Nethe

10、rlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Ce

11、ntre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 50090-5-3:2016 E BS EN 50090-5-3:2016Contents Page European foreword . 3 Introduction . 4 1 Scope 5 2 Normative references 5 3 Terms, defin

12、itions and abbreviations 5 3.1 Terms and definitions . 5 3.2 Abbreviations . 6 4 General . 6 5 HBES RF Physical Layer 7 5.1 Physical Layer for HBES RF Ready . 7 5.1.1 Signalling for HBES RF Ready . 7 5.1.2 Telegram structure for RF Ready 8 5.1.3 Medium access RF Ready 8 5.2 Physical Layer for HBES R

13、F Multi . 9 5.2.1 General requirements (HBES RF Multi). 9 5.2.2 Physical Layer type RF Multi 11 5.2.3 Telegram structure for HBES RF Multi systems 13 6 HBES RF Data Link Layer . 13 6.1 HBES RF Data Link Layer for all HBES RF devices . 13 6.1.1 Differences to existing (bidirectional) HBES EN 50090 pr

14、otocol . 13 6.1.2 Data Link Layer Frame 15 6.1.3 Use of the HBES Ctrl Field . 18 6.1.4 Data Link Layer protocol 18 6.1.5 Data Link Layer services 19 6.2 HBES RF Data Link Layer for HBES RF Ready 21 6.2.1 Data Link Layer protocol 21 6.2.2 The Layer-2 of an RF Retransmitter 21 6.3 HBES RF Data Link La

15、yer specific to HBES RF Multi systems 22 6.3.1 Medium access RF Multi . 22 6.3.2 Frame format 24 6.3.3 RF Multi-channel usage 24 6.3.4 Fast Acknowledgment 30 6.3.5 Data Link Layer protocol 35 6.3.6 Runtime with an RF Repeater and Fast Ack requested . 38 6.3.7 InterFrame delays for RF Repeaters 38 6.

16、3.8 Repetition counter . 39 6.3.9 Media Coupler 39 6.4 Semi-directional devices and bidirectional mode 39 7 Compatibility between HBES Ready and HBES RF Multi 40 7.1 Communication between HBES RF 1.1 and HBES RF1 Multi devices . 40 7.2 Communication between HBES RF Ready and HBES RF Multi devices .

17、41 7.3 Communication between HBES RF Multi and HBES RF Multi devices . 41 Bibliography 42 EN 50090-5-3:2016 (E)BS EN 50090-5-3:2016European foreword This document (EN 50090-5-3:2016) has been prepared by CLC/TC 205 “Home and Building Electronic Systems (HBES)“. The following dates are fixed: latest

18、date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-11-02 latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2018-11-02 This document supersedes EN 50090-5

19、-3:2006. EN 50090-5-3:2016 includes the following significant technical changes with respect to EN 50090-5-3:2006: - the difference between this version and the previous version of Part 5-3 is that the previous version contained only a description of the HBES RF Ready solution, where the current ver

20、sion was extended with the upward compatible HBES RF Multi solution. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. EN 50090-5-3:2016

21、 (E)BS EN 50090-5-3:2016Introduction CENELEC takes no position concerning the evidence, validity and scope of patent rights. KNX Association as Cooperating Partner to CENELEC confirms that to the extent that the standard contains patents and like rights, the KNX Associations members are willing to n

22、egotiate licenses thereof with applicants throughout the world on fair, reasonable and non-discriminatory terms and conditions. KNX Association De Kleetlaan 5, Bus 11 B-1831 Brussels-Diegem Tel: +32 (0)2 775 86 44 Mob: +32 (0) 476 21 56 58 Fax: +32 (0)2 675 50 28 e-mail: infoknx.org www.knx.org Atte

23、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. CENELEC shall not be held responsible for identifying any or all such patent rights. CEN and CENELEC maintain online lists of patents relevant to their

24、standards. Users are encouraged to consult the lists for the most up to date information concerning patents (ftp:/ftp.cencenelec.eu/EN/IPR/Patents/IPRdeclaration.pdf). EN 50090-5-3:2016 (E)BS EN 50090-5-3:20161 Scope This European Standard defines the mandatory and optional requirements for the medi

25、um specific Physical and Data Link Layer of HBES Radio Frequency. Data Link Layer interfaces and general definitions that are medium independent are given in EN 50090-4-1. This European standard defines the requirements for HBES RF Ready and HBES RF Multi devices. HBES RF Ready is a single RF channe

26、l system. HBES RF Multi is an RF multichannel evolution of HBES RF Ready system with 2 additional RF channels for fast reaction time products and 2 RF channels for slow reaction time products. HBES RF Multi, specified below provides the following features: - more reliability in Frame transmissions i

27、n presence of interferers. - more efficiency when more HBES RF products are installed at the same location. - mixing of permanent and non-permanent receiving products. - mixing of fast and slow reaction time devices. - Listen Before Talk. Fast RF channels are mainly intended to be used with human co

28、ntrolled applications like for example lights, shutters Slow RF channels are mainly intended to be used with non-permanent receivers for automatic applications like sensors (smoke, temperature, wind, etc.), heating control, etc. Compatibility issues with products in compliance with the former HBES R

29、F specification (HBES RF 1.1) and the new versions are considered in Clause 7 at the end of this document. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editio

30、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 50090-1:2011, Home and Building Electronic Systems (HBES) Part 1: Standardization structure EN 50090-4-1, Home and Building Electronic Systems (HBES) Part 4-1: Media independ

31、ent layers Application layer for HBES Class 1 EN 50090-4-2, Home and Building Electronic Systems (HBES) Part 4-2: Media independent layers Transport layer, network layer and general parts of data link layer for HBES Class 1 ETSI EN 300 220 (all parts), Electromagnetic compatibility and Radio spectru

32、m Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 50090-1:2

33、011 and the following apply. 3.1.1 RF channel hopping action to change the RF channel during or after transmitting a frame EN 50090-5-3:2016 (E)BS EN 50090-5-3:20163.1.2 budget link budget link of a device is the difference expressed in dB between the max radiated power and the radiated sensitivity.

34、 The higher the budget link, the better the radio range is 3.2 Abbreviations AFA Adaptive Frequency Agility BER Bit Error Rate D.C. Duty Cycle DLL Data Link Layer EOA End of Ack ERP Effective Radiated Power F1 F1 RF channel with a preamble of 15 ms in the transmitted Frame F1r F1 RF channel with a p

35、reamble of 4,8 ms in the transmitted Frame F1sh F1 RF channel with a preamble of 1ms in the transmitted Frame FSK Frequency Shift Keying FxOne of F1, F2 or F3 RF channels GFSK Gaussian Frequency Shift Keying LBT Listen Before Talk NPRM Non-Permanent Reception Mode PhL Physical Layer PRM Permanent Re

36、ception Mode Rx Receiver RSSI Received Signal Strength Indication SN HBES Serial Number SxOne of S1 or S2 RF channels TRx Transceiver Tx Transmitter 4 General As described in the scope, this European standard defines the RF Physical Layer requirements for: - HBES RF Ready; - HBES RF Multi. EN 50090-

37、5-3:2016 (E)BS EN 50090-5-3:2016For HBES certification in Europe, the products shall be in compliance with at least one of the following clauses. Table 1 Guide for compliance System Physical Layer Data Link Layer HBES RF Ready 5.1 6.1 and 6.2 HBES RF Multi 5.2 6.1 and 6.3 5 HBES RF Physical Layer 5.

38、1 Physical Layer for HBES RF Ready 5.1.1 Signalling for HBES RF Ready Table 2 General requirements for Physical Layer Type HBES RF Ready Characteristic Value or applicable standard Tx centre frequency fc= 868,300 MHz Bandwidth 600 kHz Max. Tx frequency tolerance 25 ppm aTx duty cycle max 1 % Tx modu

39、lation type FSK FSK deviation fDEV= 48 kHz to 80 kHz typically 60 kHz Tx chip rate 32 768 chips per second Maximum Tx chip rate tolerance 1,5 % Maximum Tx jitter per transition 5 s Tx ERP Typical : 0 dBm Min : -3 dBm Max: +14dBm Rx blocking performance according to ETSI EN 300 220-1, category 2 rece

40、ivers bRx centre frequency fc= 868,300 MHz Rx frequency tolerance 25 ppm HBES Tx to HBES Rxa, b 60 ppm Metering Tx to HBES Rxa, bMinimal Rx chip rate tolerance 2,0 %bRx radiated sensitivity typical: -95 dBmbminimal: -80 dBmbMinimal operating temperature range 0C to 45Cca This frequency tolerance inc

41、ludes tolerances due to temperature variations within the operating temperature range and tolerances due to crystal aging. b At Bit Error Rate (BER) 10-4in optimum antenna direction. c HBES Physical Layer parameters shall be met for the entire product temperature range declared by the manufacturer.

42、(e.g. : -10C to 70C for outdoor usage). A link budget of 100 dB is recommended. EN 50090-5-3:2016 (E)BS EN 50090-5-3:20165.1.2 Telegram structure for RF Ready Table 3 HBES Ready systems Telegrams definition Characteristics Value Notes Data encoding Manchester chip “0“ means fLO(= fC- fDEV) chip “1“

43、means fHI(= fC+ fDEV) bit “0“ is coded as fHIto fLOtransition, chip sequence “10“ bit “1“ is coded as fLOto fHItransition, chip sequence “01“ Preheader consists of Preamble, Manchester violation, Sync word see below Preamble 79x chip sequence “01“ sent by Tx learning sequence for Rx, number of pream

44、ble chips is not checked by Rx (4.8 ms) Manchester violation chip sequence “000111“ necessary for capture effect Sync word chip sequence “011010010110“ useful for synchronization on chip rate Postamble 2 chips to 8 chips software reasons, mandatory for all Tx, number of postamble not checked by Rx.

45、Capture effect optional Preheader allows it; Rx may use it 5.1.3 Medium access RF Ready 5.1.3.1 Definition and use Medium access control shall serve for prevention of collisions on the RF medium. For two reasons medium access cannot be completely controlled on RF. 1) Unidirectional senders access th

46、e medium at non-predictable times. 2) Non HBES RF devices access the medium at non-predictable times. Bidirectional devices shall be able to sense whether the medium is free before they transmit. The inter-Frame time shall be the time interval during which a bidirectional device shall wait for a fre

47、e medium (regardless of whether it is addressed by a preceding Frame or not). If no preamble is detected during this interFrame time the device may start sending. If a Frame is received while the Physical Layer gets a request to send, the interFrame time shall start after the Frame reception is comp

48、leted, this is after the last CRC is received. The same shall apply for sending: if the Physical Layer gets a send request while it is sending, the interFrame time shall start when the last CRC is transmitted. NOTE RF supports no collision avoidance; therefore the transmission priorities are not cod

49、ed in the Frame. EN 50090-5-3:2016 (E)BS EN 50090-5-3:20165.1.3.2 Medium Access Time Table 4 Medium access times Type of frame InterFrame time Tint Random time Trd Total medium access Time Tma REPEATED Ready frame 5 ms 0 ms Trd Limit value? Discard buffer No Yes Decrement RF Repeat Counter Data Link Layer Ph_Data.ind Ph_Data.req NOTE This flowchart only describes the handling of received messages for repeating. The handling of messages to the internal management of the Retransmitter is not shown. F