EN 50193-2-2-2016 en Electric instantaneous water heaters - Part 2-2 Performance requirements - Single point of use electric instantaneous showers - Efficiency.pdf

1、BS EN 50193-2-2:2016Electric instantaneous water heatersPart 2-2: Performance requirements Single point of use electric instantaneous showers EfficiencyBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 50193-2-2:2016 BRITISH STANDARDNational forewordThis British

2、Standard is the UK implementation of EN 50193-2-2:2016.The UK participation in its preparation was entrusted to Technical Committee CPL/59, Performance of household electrical appliances.A list of organizations represented on this committee can be obtained on request to its secretary.This publicatio

3、n does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 83189 8 ICS 91.140.65 Compliance with a British Standard cannot confer immunity fr

4、om legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigendum issued since publicationDate T e x t a f f e c t e dBS EN 50193-2-2:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50193-2-2

5、 December 2016 ICS 91.140.65 English Version Electric instantaneous water heaters - Part 2-2: Performance requirements - Single point of use electric instantaneous showers - Efficiency Chauffe-eau lectriques instantans - Partie 2-2 : Exigences daptitude la fonction - Chauffe-eau instantans de douche

6、s un seul point dutilisation - Efficacit. Elektro-Durchfluss-Wassererwrmer - Teil 2-2: Anforderungen an die Gebrauchseigenschaften - Durchfluss-Wassererwrmer fr eine einzelne Zapfstelle - Effizienz This European Standard was approved by CENELEC on 2016-10-10. CENELEC members are bound to comply with

7、 the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managem

8、ent Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the sa

9、me status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Li

10、thuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnis

11、che Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 50193-2-2:2016 EBS EN 50193-2-2:2016EN 50193-2-2:20162 Contents Page European foreword . 3 1 Scope . 4

12、 2 Normative references . 4 3 Terms and definitions. 4 4 General test conditions 4 5 Energy efficiency 4 5.1 Test method . 4 Annex A (normative) Load pattern 6 Annex B (normative) Test Set Up. 7 Annex ZZA (informative) Relationship between this European Standard and the energy labelling requirements

13、 of Commission Delegated Regulation (EU) No 812/2013 aimed to be covered 9 Annex ZZB (informative) Relationship between this European Standard and the ecodesign requirements of Commission Regulation (EU) No 814/2013 aimed to be covered 10 Bibliography 11 BS EN 50193-2-2:2016EN 50193-2-2:20163 Europe

14、an foreword This document (EN 50193-2-2) has been prepared by CLC/TC 59X “Performance of household and similar electrical appliances”. The following dates are fixed: latest date by which this document hasto be implemented at national level bypublication of an identical nationalstandard or by endorse

15、ment(dop) 2017-10-10 latest date by which the nationalstandards conflicting with thisdocument have to be withdrawn(dow) 2019-10-10 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifyi

16、ng any or all such patent rights. For the relationship with EU Directive(s) see informative Annexes ZZA and ZZB, which are an integral part of this document. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association, and suppo

17、rts essential requirements of EU Directive(s). BS EN 50193-2-2:2016EN 50193-2-2:20164 1 Scope This clause of part 1 is applicable except as follows. Addition: This standard applies to open outlet, single point of use, electric instantaneous water heaters intended for household or similar use, for sh

18、owering purposes without downstream mixing. This standard only specifies tests for the assessment of energy efficiency. This standard does not apply to electrical instantaneous water heaters covered by other parts of this series of standards. 2 Normative references This clause of Part 1 is applicabl

19、e. 3 Terms and definitions This clause of Part 1 is applicable. 4 General test conditions This clause of Part 1 is applicable except as follows. 4.3 General conditions Addition: 4.3.101 Pressure, temperature, flow and power conditions Pressure, temperature and flow measurements should be maintained

20、during testing to the tolerance detailed in Table 1. Any deviations from these tolerances will result an invalid test. All testing should be performed at the rated power for the appliance (based on a rating at 230V/400V as applicable). 4.4 Test Setup Replacement: The appliance shall be fixed in acco

21、rdance with the installation instructions except that the shower hose shall not be connected. Products covered by this standard are only to be tested to the XS load pattern detailed in Annex A, Table A.1. The measurement setup shall correspond to Annex B. 5 Energy efficiency This clause of Part 1 is

22、 applicable except as follows. 5.1 Test method 5.1.1 General Addition It is allowable to decrease the time between draw offs in order to accelerate the load pattern detailed in Annex A, as long as it can be demonstrated that results are not affected. BS EN 50193-2-2:2016EN 50193-2-2:20165 Addition 5

23、.1.1.101 Set Points The appliance shall be set to achieve minimum flow (f) as specified in Annex A for all efficiency tests. This can be increased if the appliance is unable to operate continuously and the flow rate used recorded. This flow rate is used for all individual draw offs within the prescr

24、ibed load pattern. 5.1.2 Static efficiency Addition The loss adjustment for semiconductor power switches of open outlet electronic instantaneous water heaters is not applicable for this type of appliance. 5.1.3 Start up losses Replacement The start up loss istartQ is the total energy in kWh that is

25、consumed by the appliance between energizing the heatingelements and the delivery of useable water temperature for each specific draw off i. istartQ is measured using a Wh meter for the duration between the point at which the heater elements are energised and when the outlet water has achieved the m

26、inimum temperature for useable energy, Tm. 5.1.5 Determination of smart control compliance Not applicable. 5.2.2 Daily energy demand Modification: smart= 0 BS EN 50193-2-2:2016EN 50193-2-2:20166 Annex A (normative) Load pattern This annex of part 1 is applicable except as follows. Table A.1 Addition

27、: Only load pattern XS shall be used BS EN 50193-2-2:2016EN 50193-2-2:20167 Annex B (normative) Test Set Up This annex of part 1 is applicable except as follows. Replacement: Key 1 Appliance under test (installed without outlet fittings) 8 On/Off Flow control (optional 2 Power meter 9 Flow control (

28、optional) 3 Inlet temperature sensor 10 Open water outlet 4 Flow meter 11 Outlet temperature sensor 5 Pressure reducing / regulating device 12 Temperature sensor housing (see Figures 3 and 4) 6 Pressure measurement (optional) 13 Electrical power connection 7 Connection to the water distribution netw

29、ork Figure B.1 Test setup for open-outlet instantaneous heater BS EN 50193-2-2:2016EN 50193-2-2:20168 Figure B.2 Test setup for open-outlet instantaneous heater Figure B.3 Example of thermocouple housing BS EN 50193-2-2:2016EN 50193-2-2:20169 Annex ZZA (informative) Relationship between this Europea

30、n Standard and the energy labelling requirements of Commission Delegated Regulation (EU) No 812/2013 aimed to be covered This European standard has been prepared under a Commissions standardization request, M/534 C(2015) 2625 final to provide one voluntary means of conforming to the energy labelling

31、 requirements of Commission Delegated Regulation (EU) No 812/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labelling of water heaters, hot water storage tanks and packages of water heater and solar device, OJ L239, 6.9

32、.2013. Once this standard is cited in the Official Journal of the European Union under that Regulation, compliance with the normative clauses of this standard given in Table ZZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding energy labe

33、lling requirements of that Regulation and associated EFTA Regulations. Table ZZA.1 Correspondence between this European Standard and Commission Delegated Regulation (EU) No 812/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to en

34、ergy labelling of water heaters, hot water storage tanks and packages of water heater and solar device, OJ L239, 6.9.2013 and Commissions standardization request, M/534 C(2015) 2625 final Energy labelling requirements of Regulation (EU) No 812/2013, OJ L239, 6.9.2013 Clause(s) / subclause(s) of this

35、 EN Remarks / Notes Daily electricity consumption 5.2.2 Daily energy demand Annual electricity consumption 5.2.5 Annual electricity consumption Water heater energy efficiency 5.2.4 Energy-efficiency WARNING 1: Presumption of conformity stays valid only as long as a reference to this European Standar

36、d is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2: Other Union legislation may be applicable to the products falling within the scope

37、 of this standard. BS EN 50193-2-2:2016EN 50193-2-2:201610 Annex ZZB (informative) Relationship between this European Standard and the ecodesign requirements of Commission Regulation (EU) No 814/2013 aimed to be covered This European Standard has been prepared under a Commissions standardization req

38、uest, M/534 C(2015) 2625 final to provide one voluntary means of conforming to the ecodesign requirements of Commission Regulation (EU) No 814/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for water heater

39、s and hot water storage tanks, OJ L293, 6.9.2013. Once this standard is cited in the Official Journal of the European Union under that Regulation, compliance with the normative clauses of this standard given in Table ZZB.1 confers, within the limits of the scope of this standard, a presumption of co

40、nformity with the corresponding ecodesign requirements of that Regulation and associated EFTA Regulations. Table ZZB.1 Correspondence between this European Standard and Commission Regulation (EU) No 814/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Co

41、uncil with regard to ecodesign requirements for water heaters and hot water storage tanks, OJ L293, 6.9.2013 and Commissions standardization request, M/534 C(2015) 2625 final Ecodesign requirements of Regulation (EU) No 814/2013, OJ L293, 6.9.2013 Clause(s) / subclause(s) of this EN Remarks / Notes

42、Daily electricity consumption 5.2.2 Daily energy demand Water heater efficiency 5.2.4 Energy-efficiency WARNING 1 Presumption of conformity stays valid only as long as a reference to this European Standard is maintained in the list published in the Official Journal of the European Union. Users of th

43、is standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2 Other Union legislation may be applicable to the products falling within the scope of this standard. BS EN 50193-2-2:2016EN 50193-2-2:201611 Bibliography This annex of Part 1 is a

44、pplicable. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization produ

45、cts are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been c

46、arefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find

47、 out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard

48、 copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of

49、and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior w