EN 50289-4-6-2001 en Communication Cables - Specifications for Test Methods Part 4-6 Environmental Test Methods - Temperature Cycling《通信电缆 试验方法规范 第4-6部分 环境试验方法 温度循环》.pdf

1、BRITISH STANDARD E%x% Communication cables - Specifications for test methods - Part 4-6: Environmental test methods - Temperature cycling The European Standard EN 50289-4-62001 has the status of a British Standard ICs 33.120.10 BS EN 502894-6:2001 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTE

2、D BY COPYRIGHT LAW BS EN 50289-4-6:2001 Amd. No. O BSI 14 November 2001 National foreword Date Comments This British Standard is the official English language version of The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wire and waveguides, RF connectors, a

3、nd accessories for communication and signalling, to Subcommittee EPL/46/1, Communication cables, which has the responsibility to: EN 50289-4-6:2001. - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, a

4、nd keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Eu

5、ropean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the ne

6、cessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having Summary of pages This document comprises a front cover, an inside fr

7、ont cover, the EN title page, been prepared under the direction of the Eleitrokchnical sector policv and Strategy Committee, was published under the authority ofthe standards policy and pages 2 to 7 and a back cover. The BSI copyright date displayed in this document indicates when the Strategy Commi

8、ttee on 14 November 2001 document was last issued. ISBN O 580 38692 9 E U ROPEAN STAN DARD NORME EUROPENNE EUROPISCHE NORM October 2001 ICs 33.120.10 English version Communication cables - Specifications for test methods Part 4-6: Environmental test methods - Tem peratu re cycling Cbles de communica

9、tion - Spcifications des mthodes dessai Partie 4-6: Mthodes dessais denvironnement - Cycles thermiques Kommunikationskabel- Spezifikationen fr Prfverfahren Teil 4-6: Umweltprfverfahren - Temperaturwechsel Prfung This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound

10、to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Cent

11、ral Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same st

12、atus as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC Europ

13、ean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central secretariat: rue de Stassart 35, B - 1050 Brussels O 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide f

14、or CENELEC members. Ref. No. EN 502894-6:2001 E EN 50289-4-6:2001 -2- Foreword This European Standard was prepared by the Technical Committee CENELEC TC 46X, Communication cables. The text of the draft was submitted to the formal vote and was approved by CENELEC as EN 50289-4-6 on 2001-05-01. The fo

15、llowing dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement - latest date by which the national standards conflicting with the EN have to be withdrawn (dop) 2002-04-01 (dOW) 2004-04-01 This Europea

16、n Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association. -3- EN 50289-4-6:2001 Contents 1 Scope 4 2 Normative references . 4 3 Definitions . 4 4 Test methods . 4 4.1 Equipment 4 4.2 Test sample . 4.3 Procedure

17、5 4.3.1 Initial measurement 5 4.3.3 Recovery . 6 4.4 Requirements . . 4.5 Details to be specified . 6 5 Test report . 7 4.3.2 Cycling 5 EN 50289-4-6:2001 -4- i Scope This Part 4-6 of EN 50289 details the method of test to determine the temperature cycling used in analogue and digital communication s

18、ystems. It is to be read in conjunction with Part 4-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the approp

19、riate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the public

20、ation referred to applies (including amendments). EN 50289-4-1 2001 Communication cables - Specifications for test methods - Part 4-1 : Environmental test methods - General requirements EN 50290-1-2 ) EN 60068-2-14 Communication cables - Part 1-2: Definitions Environmental testing - Part 2: Tests -

21、Test N: Change of temperature (IEC 60068-2-14) 3 Definitions For the purposes of this European Standard, the definitions of EN 50290-1-2 apply. 4 Test methods 4.1 Equipment a) Appropriate transmission measuring apparatus for determination of changes in transmission performance. b) Climatic chamber T

22、he climatic chamber shall be of a suitable size to accommodate the sample and its temperature shall be controllable to remain within I3 K of the specified testing temperature. One example of a suitable chamber is given in clause 2, test Nb, of EN 60068-2-14. 4.2 Test sample The sample shall be of su

23、fficient length as indicated in the detail specification to achieve the desired accuracy. In order to gain reproducible values, it may be necessary for the cable sample to be brought into the climatic chamber as a loose coil or on a reel. ) At draft stage. -5- EN 50289-4-6:200 1 General recommendati

24、ons are: - The winding diameter shall be large enough to maintain the ability of the cable to accommodate differential expansion and contraction. A winding diameter substantially greater than the value selected for cable delivery may be necessary. Any risk of cable expansion (or contraction) limitat

25、ion created by conditioning shall be suppressed. In particular special care should be taken to avoid residual tension on the cable during the test. For example a tight winding on a drum is not recommended as it can limit cable contraction at low temperature. On the other hand, a tight multilayer win

26、ding can limit expansion at high temperature. The use of loose winding is recommended such as large diameter coils, cushioned reels with a soft layer of zero tension facility device, etc. For optical cables, in order to limit the length of the cable under test, it is permissible to connect several f

27、ibres of the cable and to measure the connected fibres. The number of connections shall be limited and they should be located outside the climatic chamber. A sufficient number of fibres distributed over the cable structure should be tested, as defined in the Detail Specification. - - - 4.3 Procedure

28、 4.3.1 Initial measurement The sample shall be visually inspected and a basic value for the transmission parameters at the initial temperature shall be determined. Pre-conditioning conditions shall be agreed between customer and supplier. 4.3.2 Cycling The sample at ambient temperature shall be intr

29、oduced into the climatic chamber that is at the same tem pera t Ure. The temperature in the chamber shall then be lowered to the appropriate low temperature TA at the appropriate rate of cooling. After temperature stability in the chamber has been reached, the sample shall be exposed to the low temp

30、erature conditions for the appropriate period ti. The temperature in the chamber shall then be raised to the appropriate high temperature TB at the appropriate rate of heating. After temperature stability in the chamber has been reached, the sample shall be exposed to the high temperature conditions

31、 for the appropriate period tr. The temperature in the chamber shall then be lowered to the ambient temperature at the appropriate rate of cooling. This procedure constitutes one cycle (see Figure 1). The sample shall be subjected to two cycles unless otherwise required in the relevant detail specif

32、ication. Before removal from the chamber, the sample under test shall have reached temperature stability at ambient temperature. If the relevant detail specification indicates different temperature ranges for storage and used, instead of two separate tests, a combined test procedure is allowed in ac

33、cordance with figure 2. EN 50289-4-61200 1 -6- 4.3.3 Recovery If the ambient temperature is not the standard atmospheric condition to be used for testing after removal from the chamber, the sample shall be allowed to attain temperature stability at this latter condition. The relevant Detail Specific

34、ation may call for a specific recovery period for a given type of sample. 4.4 Requirements The acceptance criteria for the test shall be as stated in the Detail Specification. 4.5 Details to be specified - the permissible change of transmission parameter and inspection checks during cycling; - trans

35、mission parameters to be measured; - values of TA, TB and tl and the rate of cooling or heating; - number of cycles; - humidity levels at each temperature extreme (if any); - recovery period. 4 TL3 Temperature in the chamber TA 1 cycle A = start of first cycle Figure 1 - One cycle procedure -7- EN 5

36、0289-4-6:2001 Ti TB1 Temperature in lhe damber 1 1 cyde -+ Timet Figure 2 - Combined test procedure 5 Testreport The test report shall include: the period(s) at which inspection checks are carried out; cable sample length; type of winding: coil, reel, other (to be stated, in case of a cushioned reel

37、, the type of cushioning and material used): wind i ng diameter; single or multilayer winding; winding tension and zero tension facility device (if any): type of measurement equipment; temperature cycle diagram; change of transmission parameters as a function of temperature cycling; pass/fail criter

38、ia. BS EN 50289-4-6:200 1 BSI 389 Chiswick High Road London W4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.

39、 Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy

40、or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that sub

41、scribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: O20 8996 9001. Fax: O20 8996 7001. Standards are also available from the BSI website at htto:/www.bsi-

42、. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standar

43、ds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to da

44、te with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Cop

45、yright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

46、 in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.