EN 50343-2014 en Railway applications - Rolling stock - Rules for installation of cabling (Incorporates Amendment A1 2017).pdf

1、BSI Standards PublicationBS EN 50343:2014Railway applications Rollingstock Rules for installationof cablingBS EN 50343:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 50343:2014. Itsupersedes BS EN 50343:2003 which is withdrawn.The UK participation in its p

2、reparation was entrusted to TechnicalCommittee GEL/9/2, Railway Electrotechnical Applications - Rollingstock.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users

3、are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 73003 0ICS 45.060.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theS

4、tandards Policy and Strategy Committee on 30 June 2014.Amendments issued since publicationDate Text affectedBS EN 50343:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50343 May 2014 ICS 45.060.01 Supersedes EN 50343:2003English Version Railway applications - Rolling stock - Rules for insta

5、llation of cabling Applications ferroviaires - Matriel roulant - Rgles dinstallation du cblage Bahnanwendungen - Fahrzeuge - Regeln fr die Installation von elektrischen Leitungen This European Standard was approved by CENELEC on 2014-01-27. CENELEC members are bound to comply with the CEN/CENELEC In

6、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to an

7、y CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the of

8、ficial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg

9、, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CEN

10、ELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 50343:2014 EBS EN 50343:2014EN 50343:2014 2 Contents 1 Scope 6 2 Normative references 6 3 Terms, definitions and abbrevia

11、tions 8 3.1 Terms and definitions 8 3.2 Abbreviations . 10 4 Technical requirements 10 4.1 General requirements 10 4.2 Selection of type and size of cables 11 4.2.1 General . 11 4.2.2 Selection of cable size for control cables 12 4.2.3 Selection of cable size for cables for power distribution, on th

12、e basis of continuous load current . 12 4.2.4 Selection of cable size for cables for power distribution, on the basis of rating of protection device 18 4.2.5 Motor cables . 18 4.2.6 Cables for protective bonding . 18 4.2.7 Cables used under short time current (below 5 s) 18 4.3 Bundling of cables .

13、19 4.4 Flexibility of cables. 19 4.5 Minimum cross-sectional area of conductors 20 4.6 Use of green and yellow colour . 20 4.7 Bending radii and other mechanical requirements 20 4.8 Re-termination . 22 4.9 Busbars . 22 4.10 Connections to busbars . 23 4.11 Separation of cables with different voltage

14、 levels and for safety reasons . 23 4.12 Provisions for refurbishment and maintenance, including inspection and repair 24 4.13 Fire prevention, cable laying and cabling behaviour in case of fire . 25 4.14 Provision of spares 26 4.14.1 Provision of spares for control cabling 26 4.14.2 Provision of sp

15、ares for auxiliary power distribution cabling. 26 4.15 Requirements for fixing . 26 4.16 Clearances and creepage distances . 27 4.17 Requirements for electrical terminations . 27 4.17.1 General . 27 4.17.2 Electrical terminations at the cable ends 28 4.17.3 Electrical terminations at the terminal or

16、 device side 28 4.18 Use of heat-shrinkable sleeves . 30 4.19 Connections for return current . 30 4.20 Storage of cables . 30 4.21 Cable conduits . 31 4.22 Electrical bolted connections . 31 5 EMC requirements . 33 5.1 General 33 5.2 Cable categories 34 5.3 Separation of cables 34 5.4 Return conduct

17、or . 35 5.5 Use of conductive structure . 35 5.6 Shielding and earthing . 35 5.7 Supply connection from battery . 35 5.8 Databus lines . 36 6 Marking for identification . 36 6.1 General 36 6.2 Marking for identification of cables and busbars . 36 6.3 Marking for identification of terminal blocks, in

18、dividual terminals, plugs and sockets . 37 6.4 Marking of insulators . 37 6.5 Marking for warning against electrical shock . 37 BS EN 50343:2014 3 EN 50343:2014 6.6 Marking using heat-shrinkable sleeves . 37 7 Testing 37 7.1 General concerning testing 37 7.2 Electrical insulation tests . 38 7.2.1 Ge

19、neral . 38 7.2.2 Voltage withstand test . 38 7.2.3 Insulation impedance test . 40 Annex A (normative) Cable sizing Calculation under short time current conditions 42 Annex B (informative) Cable sizing Examples of current ratings 43 Annex C (normative) Cable sizing Calculating current ratings for tem

20、perature classes other than 90 C . 45 Annex D (normative) Cable sizing Correction factor k1for expected ambient temperature . 46 Annex E (normative) Cable sizing Prediction of cable lifetime 47 E.1 General cable lifetime considerations . 47 E.2 Reducing cable lifetime . 48 E.3 Increasing cable lifet

21、ime 49 Annex F (informative) Cable sizing Calculation examples . 50 Annex G (informative) Terminations 54 G.1 Methods of terminating cables 54 G.2 Tensile strength test values . 60 Annex H (normative) Tests on marking when using heat-shrinkable sleeves 62 H.1 General 62 H.2 Preparation of specimens

22、62 H.3 Testing of specimens 63 H.4 Result of test 63 Annex I (informative) Effects of the number of earth connections to a cable screen. 64 Annex J (informative) Differences of electrochemical potentials between some conductive materials . 65 Electrolyte: water with 2 % NaCl salt. 65 Source: EN 3197

23、:2010. 65 Annex K (informative) Locations on board rolling stock to be distinguished . 66 Bibliography 68 Tables Table 1 Modification factor k5for individual cores within a multi core cable . 15 Table 2 Modification factor k2for installation type (grouping and installation conditions) . 16 Table 3 S

24、election of cable conductor size on the basis of rating of protection device . 18 Table 4 Minimum internal bending radii R for static applications . 21 Table 5 Cable categories with respect to EMC 34 Table 6 Minimum distances between cables of different EMC categories . 34 Table 7 Test voltages acco

25、rding to on-board voltages 40 Table 8 Test voltages according to supply line voltages 40 Table A.1 Modification factor k4. 42 Table B.1 Examples of current ratings for standard wall cables, with 90 C maximum conductor operating temperature 44 Table C.1 Factor k*, used when comparing current ratings

26、for 90 C maximum conductor operating temperature with other temperature classes 45 BS EN 50343:2014EN 50343:2014 4 Table D.1 Modification factor k1. 46 Table E.1 Examples of values of correction factor k3to allow for decrease in predicted cable lifetime for a 90 C cable 46 Table G.1 Methods of termi

27、nating cables Conductor side 54 Table G.2 Methods of terminating cables Terminal side Crimp connections (1/2) 55 Table G.3 Methods of terminating cables Terminal side Screwed and bolted connection 57 Table G.4 Methods of terminating cables Terminal side Connection by clamping 58 Table G.5 Methods of

28、 terminating cables Terminal side Connection by insulation displacement or penetration . 59 Table G.6 National standards for termination methods . 60 Table G.7 Pull out force for crimp connections 61 Table H.1 Preparation of heat-shrinkable sleeve for test of marking quality 62 Table I.1 Effects of

29、shielding 64 Table J.1 Differences of electrochemical potentials between some conductive materials (in mV) 65 BS EN 50343:2014 5 EN 50343:2014 Foreword This document (EN 50343:2014) has been prepared by CLC/SC 9XB “Electromechanical material on board rolling stock“. The following dates are fixed: la

30、test date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-01-27 latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2017-01-27 Attention is drawn to the poss

31、ibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 50343:2003. EN 50343:2014 includes the following significant technical changes with resp

32、ect to EN 50343:2003: references to other standards updated and harmonized; factor k5concerning sizing of multi core cables introduced; factor k2detailed, see Table 2; short time current detailed; mechanical aspects detailed; separation of cables due to safety reasons and EMC reasons harmonized; det

33、ails added and changed concerning electrical and mechanical requirements for electrical terminations; cable lifetime considerations updated. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association. BS EN 50343:2014EN 50343:2

34、014 6 1 Scope This European Standard specifies requirements for the installation of cabling on railway vehicles and within electrical enclosures on railway vehicles, including magnetic levitation trains and trolley buses. NOTE With respect to trolley buses, this European Standard applies to the whol

35、e electric traction system, including current collecting circuits, power converters and the respective control circuits. The installation of other circuits is covered by street vehicle standards for example those for combustion driven buses. This European Standard covers cabling for making electrica

36、l connections between items of electrical equipment, including cables, busbars, terminals and plug/socket devices. It does not cover special effect conductors like fibre optic cables or hollow conductors (waveguides). The material selection criteria given here are applicable to cables with copper co

37、nductors. This European Standard is not applicable to the following: special purpose vehicles, such as track-laying machines, ballast cleaners and personnel carriers; vehicles used for entertainment on fairgrounds; vehicles used in mining; electric cars; funicular railways. As the field of cabling i

38、n rolling stock is also dealt with in the cable makers standard, references are made to EN 50264 series, EN 50306 series, EN 50382 series and EN 50355. This European Standard applies in conjunction with the relevant product and installation standards. Stricter requirements than those given in this E

39、uropean Standard may be necessary. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

40、enced document (including any amendments) applies. EN 45545 (all parts), Railway applications Fire protection on railway vehicles EN 45545-1, Railway applications Fire protection on railway vehicles Part 1: General EN 45545-2, Railway applications Fire protection on railway vehicles Part 2: Requirem

41、ents for fire behaviour of materials and components EN 45545-3 Railway applications - Fire protection on railway vehicles - Part 3: Fire resistance requirements for fire barriers EN 45545-5, Railway applications Fire protection on railway vehicles Part 5: Fire safety requirements for electrical equi

42、pment including that of trolley buses, track guided buses and magnetic levitation vehicles EN 50121-3-1, Railway applications Electromagnetic compatibility Part 3-1: Rolling stock Train and complete vehicle EN 50121-3-2, Railway applications Electromagnetic compatibility Part 3-2: Rolling stock Appa

43、ratus EN 50124-1, Railway applications Insulation coordination Part 1: Basic requirements Clearances and creepage distances for all electrical and electronic equipment BS EN 50343:2014 7 EN 50343:2014 EN 50125-1, Railway applications Environmental conditions for equipment Part 1: Equipment on board

44、rolling stock EN 50153, Railway applications Rolling stock Protective provisions relating to electrical hazards EN 50200, Method of test for resistance to fire of unprotected small cables for use in emergency circuits EN 50215:2009, Railway applications Rolling stock Testing of rolling stock on comp

45、letion of construction and before entry into service EN 50264 (all parts), Railway applications Railway rolling stock power and control cables having special fire performance EN 50306 (all parts), Railway applications Railway rolling stock cables having special fire performance Thin wall EN 50306-2,

46、 Railway applications Railway rolling stock cables having special fire performance Thin wall Part 2: Single core cables EN 50355:2013, Railway applications - Railway rolling stock cables having special fire performance - Guide to use EN 50362, Method of test for resistance to fire of larger unprotec

47、ted power and control cables for use in emergency circuits EN 50382 (all parts), Railway applications Railway rolling stock high temperature power cables having special fire performance EN 50467, Railway applications Rolling stock Electrical connectors, requirements and test methods EN 50553, Railwa

48、y applications Requirements for running capability in case of fire on board of rolling stock EN 60228, Conductors of insulated cables (IEC 60228) EN 60423, Conduit systems for cable management - Outside diameters of conduits for electrical installations and threads for conduits and fittings (IEC 604

49、23) EN 60684-3-212, Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 212: Heat-shrinkable polyolefin sleevings (IEC 60684-3-212) EN 60684-3-216 , Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 216: Heat-shrinkable, flame-retarded, limited-fire hazard sleeving (IEC 60684-3-216) EN 60684-3-2