EN 60034-7-1993 en Rotating Electrical Machines - Part 7 Classification of Types of Construction Mounting Arrangements and Twerminal Box Position (IM Code) (Incorporates Amendment .pdf

1、BRITISH STANDARD Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code) The European Standard EN 60034-7:1993 with the incorporation of amendment A1:2001 has the status of a British Standard ICs 29.160.01 BS EN IEC 60

2、 034-7993 60034-7: 1992 Incorporating Amendment No. 1 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT JAW COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesBS EN 60034-7:1993 Amd. No. 13216 The following BSI references relate

3、 to the work on this standard: Committee reference PWi haft for comment 87/25137 DC Cooperating organizations Date Comments 5 October 2001 See national foreword The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, compris

4、es the national committees of the following countries: Austria Belgium Denmark Finland France Germany Greece Iceland Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom This British Standard, having been prepared under the direction of the Power Electrical En

5、gineering Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 October 1993 0 MI 5 October 2001 Amendments issued since publication ISBN O 580 22563 1 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information

6、Handling ServicesBS EN 60034-7:1993 Contents Page Cooperating organizations Inside front cover National foreword 11 Foreword 2 Text of EN 60034-7 3 National annex NA (informative) Committees responsible Inside back cover 8 BSI 5 October 2001 i COPYRIGHT European Committee for Electrotechnical Standa

7、rdizationLicensed by Information Handling ServicesBS EN 60034-71993 National foreword This British Standard has been prepared under the direction of the Power Electrical Engineering Standards Policy Committee and is the English language version of EN 60034-7:1993 Rotating electrical machines -Part 7

8、: Classification of types of construction mounting arrangements, and terminal boxposition (IM Code) including amendment A1:2001 published by the European Committee for Electrotechnical Standardization (CENELEC). It was derived by CENELEC from IEC 60034-7: 1992 including amendment 1:2000 published by

9、 the International Electrotechnical Commission (IEC). This British Standard supersedes BS 4999-107:1987 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags B a. Tags indicating changes to IEC text carry the number of the IEC amendment.

10、 For example, text altered by IEC amendment 1 is indicated byB a. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered to IEC 60027-1. For a period of time during the change over from one numbering system to the other, pu

11、blications may contain identifiers from both systems. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal

12、obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 25 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. 11 Q BSI 5 October 2001 COPYRIGHT European C

13、ommittee for Electrotechnical StandardizationLicensed by Information Handling ServicesEUROPEAN STANDARD EN 60034-7 NORME EUROPENNE January 1993 EUROPISCHE NORM +Al March 2001 UDC 62 1.3 13001.4:003.62 Supersedes HD 53.7 S1:1974 Descriptors: Rotating electrical machine, classification, designation, t

14、ypes of construction, mounting arrangements, IM code English version Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code) (includes amendment A1:2001) (IEC 60034-71992 + A1:2000) Machines lectriques tournantes - Par

15、tie 7: Classification des modes de construction, des dispositions de montage et position de la bote bornes (Code IM) (inclut lamendement A1:2001) Drehende elektrische Maschinen - Teil 7: Klassifizierung der Bauarten, der Aufstellungsarten und der Klemmkasten-Lage (IM-Code) (enthlt Anderung A1:2001)

16、(CE1 60034-7: 1992 + A1:2000) (IEC 60034-7:1992 + A1:2000) This European Standard was approved by CENELEC on 1992-03-24. Amendment Al was approved by CENELEC on 2000-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eu

17、ropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (E

18、nglish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austri

19、a, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komite

20、e fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 0 1993 Copyright reserved to CENELEC members Ref. No. EN 60034-7:1993 + A1:2001 E COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesEN 60034-7:1993 Foreword

21、 The text of document 2H(C0)29, as prepared by subcommittee 2H: Degrees of protection, methods of cooling and mounting arrangements, of IEC technical committee 2: Rotating machinery, was submitted to the IEC-CENELEC parallel vote in July 1991. The reference document was approved by CENELEC as EN 600

22、34-7 on 24 March 1992. The following dates were fixed: - latest date of publication of an identical national - latest date of withdrawal of conflicting national standard (dop) 1993-12-01 standards (dow) 1993-12-01 Foreword to amendment Al The text of document 2/1095/FDIS, future amendment 1 to IEC 6

23、0034-7:1992, prepared by IEC TC 2, Rotating machinery, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment Al to EN 60034-7:1993 on 2000-11-01. The following dates were futed: - latest date by which the amendment has to be implemented at national level by publicat

24、ion of an identical national standard - latest date by which the national standards conflicting with the amendment have to be or by endorsement (dop) 2001-08-01 withdrawn (dow) 2003-11-01 Contents Page Foreword 2 Section i. Scope and definitions 1.1 Scope 3 1.2 Definitions 3 Section 2. Code I (Alpha

25、-numeric designation) 2.1 Designation of machines with 2.2 Designation of machines with horizontal shafts 5 vertical shafts 8 E9 2.3 Terminal box location 11 a Section 3. Code II (All-numeric designation) 3.1 Designation 13 3.2 Significance of the first numeral 13 3.3 Significance of the fourth nume

26、ral 13 3.4 Significance of the second and third numerals 13 3.5 Terminal box location 14 3.6 Examples of designations 14 Annex A (informative) Relationship between Code I and Code II 24 Table 1 - Designations for machines with horizontal shafts (IM B) 6 Table 2 - Designations for machines with verti

27、cal shafts (IM V) 8 Table 3 - Significance of the first numeral 13 Table 4 - Significance of the fourth numeral 13 Table 5 - significance of second and third numerals for first numeral i 15 Table 6 - Significance of second and third numerals for first numeral 2 16 Table 7 - Significance of second an

28、d third numerals for first numeral 3 17 Table 8 - Significance of second and third numerals for first numeral 4 18 Table 9 - Significance of second and third numerals for first numeral 5 19 Table 10 - Significance of second and third numerals for first numeral 6 20 Table 11 - Significance of second

29、and third numerals for first numeral 7 21 Table 12 - Significance of second and third numerals for first numeral 8 22 Table 13 - Significance of second and third numerals for first numeral 9 23 a Q BSI 5 October 2001 2 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Info

30、rmation Handling ServicesEN 60034-7:1993 Section 1. Scope and definitions 1.1 Scope This part of IEC 34 specifies the IM code, a classification of types of construction and mounting arrangements of rotating electrical machines. Two systems of classification are provided as follows: - Code I (see sec

31、tion 2): - Code II (see section 3): An alpha-numeric designation applicable to machines with endshield bearing(s) and only one shaft extension. An all-numeric designation applicable to a wider range of types of machines including types covered by Code I. The type of machine not covered by Code II sh

32、ould be fully described in words. The relationship between Code I and Code II is given in Annex A. 1.2 Definitions For the purposes of this part of IEC 34, the following definitions apply: 1.2.1 type of construction the arrangement of machine components with regard to fixings, bearing arrangement an

33、d shaft extension (IEV 4 11- 13-34)l) 1.2.2 mounting arrangement the orientation on site of the machine as the whole with regard to shaft alignment and position of fixings (IEV 411-13-35) 1.2.3 shaft extension a portion of a shaft extending beyond an extreme bearing (IEV 411-13-07) NOTE 1.2.4 drive-

34、end of a machine (D-end) that end of the machine which accommodates the shaft end (IEV 411-13-36) NOTE This is normally the driving end of a motor or the driven end of a generator. Where for some machines the above definition is inadequate, the D-end is defined as follows: The bearing may be on the

35、machine itself or be part of an assembly comprising a machine and (an) additional bearing(s). a) machine with two shaft extensions of different diameter: the end with the larger shaft diameter; b) machine with a cylindrical shaft extension and a conical shaft extension of the same diameter: the end

36、with cylindrical shaft extension; c) machine with other arrangements: according to IEC 34-8 if applicable; otherwise by agreement. NOTE 1.2.5 non-drive end of the machine (N-end) that end of the machine opposite to the drive end (IEV 411-13-37) The outer diameter of a forged-on flange is taken to be

37、 the diameter of the shaft extension. 1) IEC 50 (411):1973, International Electrotecbnical Vocabulary (IEV), Chapter 411: Rotating machines. Q BSI 5 October 2001 3 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Services4 blank COPYRIGHT European Com

38、mittee for Electrotechnical StandardizationLicensed by Information Handling ServicesEN 60034-7:1993 Section 2. Code I (Alpha-numeric designation) 2.1 Designation of machines with horizontal shafts In Code I, a machine with a horizontal shaft is designated by the Code letters IM (Lnternational Mounti

39、ng), followed by a space, the letter B and one or two numerals, as shown in Table 1. 5 0 BSI 5 October 2001 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesEN 60034-7:1993 Section 2 Table 1 - Designations for machines with horizontal shafts (

40、IM B) Type of construction Mounting arrangement (Horizontal shah) Sketch Number of end- shield DeSig- nabion Mounted by Eeet feet down IM B3 2 2 2 2 M0Untedbyf-t feet UP 2 2 6 O BSI 5 October 2001 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Servi

41、cesSection 2 EN 60034-7:1993 - DeSig- nation IM 815 IM 820 IM 25 IM 3 IM 634 IM 835 Feet Table 1 - Designations for machines with horizontal shafts (IM B) (conchded) arrangement (Horizontal shaft) Flange Other details Sketch Wmi Deet Nurnbei of end- shield I- bearing! No endshieldor Mounted by feet

42、feet - Addiional mounting mounting on end face bearing at Bend down,with adational provisions on D-end of frame of hame I +qJ2 . 1 322 2 I Mounting Type of construction mm raioed feet - II . -; 0 BSI 5 October 2001 7 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Inform

43、ation Handling ServicesEN 60034-71993 Section 2 Type of construction Number ofend- Feet Flange Other details shield bearings 2.2 Designation of machines with vertical shafts In Code I, a machine with a vertical shaft is designated by the Code letters TM (International Mounting) followed by a space,

44、the letter V and one or two numerals, as shown in Table 2. Table 2 - Designations for machines with vertical shafts (IM V) Mounting arrangement (Vertical shaft) DeSig- naiion IM V1 IM v2 IM V3 IM V4 IM V5 IM V6 - Sketch 0 BSI 5 October 2001 8 COPYRIGHT European Committee for Electrotechnical Standar

45、dizationLicensed by Information Handling ServicesSection 2 EN 60034-7:1993 Q BI 5 October 2001 9 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesEN 60034-7:1993 Section 2 Table 2 - Designations for machines with vertical shafts V) (concluded)

46、 - 2 2 2 2 - 2 - - - With feel - wim feet Type of Oonstnrlion hgo omeidoosilo mh mdhkJdf b) machines with flange only and with drains shall be viewed from the D-end and with the drains at 6 oclock; c) other configurations shall not have a coding. The coding shall conform to the following table: I Le

47、tter designation 1 None B 3.6 Examples of designations a In Table 5 to Table 13 common types of construction and mounting arrangements are illustrated by sketches, and their designations are given using a particular fourth numeral. Other fourth numerals could be applicable (see Table 4). The absence

48、 of a sketch does not imply that a designation is not available. Numerals to which a significance has been allocated in the appropriate tables may be combined to form a valid designation. Some of these designations may be impracticable. 14 0 BSI 5 October 2001 COPYRIGHT European Committee for Electr

49、otechnical StandardizationLicensed by Information Handling ServicesSection 3 EN 60034-71993 Table 5 - Significance of second and third numerals for first numeral 1 (Foot-mounted machines with endshield bearing(s) only) Machineconsmiclion Designation and skeech (-3.5) 0 BSI 5 October 2001 15 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesEN 60034-71993 Section 3 MachineconsmJUjon Table 6 - Significance of second and third numerals for first numeral 2 (Foot-and-flange-mounted machines with endshield bearin