EN 60038-2011 en CENELEC standard voltages《CENELEC标准电压[代替 CENELEC HD 472 S1 A1 CENELEC HD 472 S1]》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationCENELEC standard voltagesBS EN 60038:2011National forewordThis British Standard is the UK implementation of EN 60038:2011. It is identical to IEC 60038:2009. It supersedes BS 769

2、7:1993, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GEL/8, Systems Aspects for Electrical Energy Supply.A list of organizations represented on this committee can be obtained on request to its secretary.BSI, as a member of CEN, is obliged to publish

3、 EN 60038:2011 as a British Standard. However, attention is drawn to the fact that during the development of this European Standard, the UK committee voted against its approval as a European Standard.BS EN 60038 specifies standard voltage values which are intended to serve as preferential values for

4、 the nominal voltage of electrical supply systems, and as reference values for equipment and system design. The reference values contained within this standard do not replace or modify the values given in product standards.It has been developed from the IEC Standard IEC 60038.BS EN 60038 is therefor

5、e not intended to set definitive limits for voltages which may be present either on the electricity supply network or in a customers installation. Other Standards also exist in this area, including BS EN 50160, Voltage characteristics of electricity supplied by public electricity networks, and HD 60

6、364-5-52, Low voltage electrical installations Part 5-52: Selection and erection of electrical equipment Wiring systems (IEC 60364-5-52). BS EN 50160 describes the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public electricity network

7、s under normal operating conditions and does not describe the average situation usually experienced by an individual network user. HD 60364-5-52 covers voltages which may be experienced within a customers installation. HD 60364 is implemented in the UK by BS 7671 (IET Wiring Regulations).In Great Br

8、itain, voltage limits at a customers electricity supply terminals are legally defined by Regulation 27 of the Electricity Safety, Quality and Continuity Regulations (ESQCR) 2002, as amended. In Northern Ireland, Regulation 30 of the Electricity Supply Regulations (Northern Ireland) 1988, as amended,

9、 applies.BS 7697:1993, Nominal voltages for low voltage public electricity supply systems, was the implementation of an earlier CENELEC Harmonisation Document, HD 472 S1:1989.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correc

10、t application. BSI 2011ISBN 978 0 580 74988 9ICS 29.020Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2011.Amendments/corrigenda issued since public

11、ationDate Text affectedBRITISH STANDARDBS EN 60038:2011The CENELEC common modifications have been implemented at the appropriate places in the text. The start and finish of each common modifcation is indicated in the text by tags .EUROPEAN STANDARD EN 60038 NORME EUROPENNE EUROPISCHE NORM October 20

12、11 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved w

13、orldwide for CENELEC members. Ref. No. EN 60038:2011 E ICS 29.020 Supersedes HD 472 S1:1989 + corr. Feb.2002 + A1:1995English version CENELEC standard voltages (IEC 60038:2009, modified) Tensions normales du CENELEC (CEI 60038:2009, modifie) CENELEC-Normspannungen (IEC 60038:2009, modifiziert) This

14、European Standard was approved by CENELEC on 2011-09-05. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refer

15、ences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

16、 CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Ge

17、rmany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 2 Contents Foreword . 3 1 Scope . 4 2 Normative references 4 3 Terms and definitions 5 4 S

18、tandard voltages . 6 4.1 AC systems having a nominal voltage between 100 V and 1 000 V inclusive and related equipment . 6 4.2 DC and a.c. traction systems 6 4.3 AC three-phase systems having a nominal voltage above 1 kV and not exceeding 35 kV and related equipment 7 4.4 AC three-phase systems havi

19、ng a nominal voltage above 35 kV and not exceeding 230 kV and related equipment . 8 4.5 AC three-phase systems having a highest voltage for equipment exceeding 245 kV 9 4.6 Equipment having a nominal voltage below 120 V a.c. or below 750 V d.c. . 10 Annex ZB (informative) A-deviations 11 Bibliograph

20、y 12 Tables Table 1 AC systems having a nominal voltage between 100 V and 1 000 V inclusive and related equipment a. 6 Table 2 DC and a.c. traction systems a. 7 Table 3 AC three-phase systems having a nominal voltage above 1 kV and not exceeding 35 kV and related equipment a. 7 Table 4 AC three-phas

21、e systems having a nominal voltage above 35 kV and not exceeding 230 kV and related equipment a. 8 Table 5 AC three-phase systems having a highest voltage for equipment exceeding 245 kV a9 Table 6 Equipment having a nominal voltage below 120 V a.c. or below 750 V d.c. 10 BS EN 60038:2011 EN 60038:20

22、11 (E) 3 Foreword This document (EN 60038:2011) consists of the text of IEC 60038:2009 prepared by IEC/TC 8, “Systems aspects for electrical energy supply “, together with the common modifications prepared by CLC Technical Body 8X, “System aspects of electrical energy supply“. The following dates ar

23、e fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-09-05 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-09-05 This European Standard supersedes

24、 HD 472 S1:1989 + corrigendum February 2002 + A1:1995. In this standard, the common modifications to the International Standard are indicated byThe main common modifications to IEC 60038:2009 are the following. All references to 60 Hz are removed in the European Standard (reason: 60 Hz is not used i

25、n Europe for a.c. electric systems). The “in some countries“ notes related to non-CENELEC countries are removed. The value of 100 kV as highest voltage for equipment corresponding to the value of 90 kV as nominal system voltage is added to Table 4 (reason: this value already exists in EN 62271-1 and

26、 is widely used in French transmission systems). Sentences containing recommendations are generally put in notes. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or

27、 all such patent rights. tags .BS EN 60038:2011 EN 60038:2011 (E) 4 CENELEC STANDARD VOLTAGES 1 Scope This publication applies to a.c. transmission, distribution and utilization systems and equipment for use in such systems with a standard frequency of 50 Hz having a nominal voltage above 100 V; a.c

28、. and d.c. traction systems; a.c. and d.c. equipment having nominal voltages below 120 V a.c. or below 750 V d.c., the a.c. voltages being intended (but not exclusively) for 50 Hz applications;batteries (from primary or secondary cells), other power supply devicesequipment (including industrial and

29、communication), and appliances. NOTE Z1 Only standard frequency 50 Hz is used in Europe for public a.c. transmission and distribution systems. For systems and equipment at 60 Hz, see IEC 60038. This publication does not apply to voltages representing or transmitting signals or measured values. This

30、publication does not apply to standard voltages of components and parts used within electrical devices or items of equipment. This publication specifies standard voltage values which are intended to serve as preferential values for the nominal voltage of electrical supply systems, and as reference v

31、alues for equipment and system design. NOTE 1 Two main reasons have led to the values specified in this standard: The values of nominal voltage (or highest voltage for equipment) specified in this standard are mainly based on the historical development of electrical supply systems throughout the wor

32、ld, since these values turned out to be the most common ones, and have achieved worldwide recognition; The voltage ranges mentioned in this standard have been recognized to be the most appropriate ones as a basis for design and testing of electrical equipment and systems. NOTE 2 It is nevertheless t

33、he task of system and product standards to define appropriate testing values, testing conditions and acceptance criteria. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undate

34、d references, the latest edition of the referenced document (including any amendments) applies. HD 60364-5-52, Low voltage electrical installations Part 5-52: Selection and erection of electrical equipment Wiring systems (IEC 60364-5-52) Text deleted(a.c. or d.c.), electrical such equipment covers T

35、ext deletedBS EN 60038:2011 EN 60038:2011 (E) 5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. For alternating voltages, the voltages stated below are r.m.s. values. 3.1 nominal system voltage a suitable approximate value of voltage used to desi

36、gnate or identify a system IEV 601-01-21, modified 3.2 highest voltage of a system (excluding transient or abnormal conditions) the highest value of operating voltage which occurs under normal operating conditions at any time and at any point on the system NOTE It excludes transient overvoltages, su

37、ch as those due to switching operations, and temporary variations of voltage. IEV 601-01-23, modified 3.3 lowest voltage of a system (excluding transient or abnormal conditions) the lowest value of operating voltage which occurs under normal operating conditions at any time and at any point on the s

38、ystem NOTE It excludes transient voltages, such as those due to switching operations, and temporary variations of voltage. IEV 601-01-24, modified 3.4 supply terminals point in a transmission or distribution network designated as such and contractually fixed, at which electrical energy is exchanged

39、between contractual partners 3.5 supply voltage the phase-to-phase or phase-to-neutral voltage at the supply terminals NOTE An equivalent definition is: the line-to-line or line-to-neutral voltage at the supply terminals. 3.6 supply voltage range the voltage range at the supply terminals 3.7 utiliza

40、tion voltage the phase-to-phase or phase-to-neutral voltage at the outlets or at the points where utilization equipment is intended to be connected to the fixed installation NOTE An equivalent definition is: the line-to-line or line-to-neutral voltage at the outlets or at the points where utilizatio

41、n equipment is intended to be connected to the fixed installation. 3.8 utilization voltage range the voltage range at the outlets or at the points where utilization equipment is intended to be connected to the fixed installation NOTE Attention is drawn to the fact that in some equipment standards (f

42、or example, EN 60335-1 and EN 60071 ), the term “voltage range“ has a different meaning. BS EN 60038:2011 EN 60038:2011 (E) 6 3.9 highest voltage for equipment highest voltage for which the equipment is specified regarding: a) the insulation; b) other characteristics which may be linked to this high

43、est voltage in the relevant equipment recommendations. NOTE Equipment may only be used on systems having a highest system voltage less than or equal to its highest voltage for equipment. 4 Standard voltages 4.1 AC systems having a nominal voltage between 100 V and 1 000 V inclusive and related equip

44、ment The nominal voltage of an a.c. system in the range from 100 V to 1 000 V should be selected from the values given in Table 1. Table 1 AC systems having a nominal voltage between 100 V and 1 000 V inclusive and related equipment Three-phase four-wire or three-wire systems aNominal voltage (at 50

45、 Hz) bV 230 230/400 400/690 1 000 a The three-phase four-wire systems include single-phase circuits (extensions, services, etc.) connected to these systems. b The lower values are voltages to neutral and the higher values are voltages between phases. When one value only is indicated, it refers to th

46、ree-wire systems and specifies the voltage between phases. Voltages in excess of 230/400 V are intended for heavy industrial applications and large commercial premises. Concerning supply voltage range, under normal operating conditions, the supply voltage should not differ from the nominal voltage o

47、f the system by more than 10 %. For the utilization voltage range, in addition to the voltage variations at the supply terminals, voltage drops may occur within the consumers installations. For more information, see HD 60364-5-52 . This utilization voltage range should be taken into account by produ

48、ct committees. 4.2 DC and a.c. traction systems The voltages of a d.c. or a.c. traction system should be selected from the values given in Table 2. Text deleted BS EN 60038:2011 EN 60038:2011 (E) 7 Table 2 DC and a.c. traction systems aVoltageNominal frequency of a.c. systems Lowest Nominal Highest

49、V V V Hz DC systems (400) (600) (720) 500 750 900 1 000 1 500 1 800 2 000 3 000 3 600bAC single-phase systems (4 750) (6 250) (6 900) 50 12 000 15 000 17 250 16 2/3 19 000 25 000 27 500 50 a The values indicated in parentheses should be considered as non-preferred values. It is recommended that these values should not be used for new systems to be constructed in future. In particular for a.c. single-phase systems, the nominal voltage 6 250 V s