EN 60169-23-1993 en Radio-Frequency Connectors Part 23 Pin and Socket Connector for Use with 3 5 mm Rigid Precision Coaxial Lines with Inner Diameter of Outer Conductor 3 5 mm (0 1.pdf

1、- m 3404583 O092823 458 m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60169-23 September 1993 UDC 621.316.541.029.51.7 Descriptors: Radio-frequency connectors pin and socket, rigid coaxial lines English version Radio-frequency connectors Part 23: Pin and socket connector for use with 3, 5 m

2、m rigid precision coaxial lines with inner diameter of outer conductor 3,5 mm (0,1378 in) (IEC 169-23 : 1991) Connecteurs pour frquences radiolectriques Hochfrequenz-Steckverbindungen Vingt-troisime partie: Connecteur mle et femelle pour lignes rigides coaxiales de prcision de 3,5 mm avec diamtre in

3、trieur du conducteur extrieur de 3,5 mm Teil 23: Stift- und Buchsen-Stecker fr 3,5 mm Przisions-Koaxial-Leitungen mit einem Innendurchmesser des AuBenleiters von 3,5 mm (0,1378 in) (0,1378 in) (CE1 169-23 : 1991) (IEC 169-23 : 1991) This European Standard was approved by CENELEC on 1993-07-06. CENEL

4、EC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on app

5、lication to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secreta

6、riat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC E

7、uropean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels O 1993 Copyright reserved to CENELEC members Ref. No. EN 60169-23 : 1993 E m 3404583 009282

8、4 354 m Page 2 EN 60169-23 : 1993 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC 169-23 : 1991 could be accepted without textual changes, has shown that no common modifications were necessary for the acceptance as European Standa

9、rd. The reference document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN 60169-23 on 6 July 1993. The following dates were fixed: - latest date of publication of an identical national standard (dop) 1994-08-01 - latest date of withdrawal of conflicting nation

10、al standards (dow) 1994-08-01 For products which have complied with the relevant national standard before 1994-08-01 , as shown by the manufacturer or by a certification body, this previous standard may continue to apply for production until 1999-08-01. Annexes designated normative are part of the b

11、ody of the standard. In this standard, annex ZA is normative. 3404ES83 0092825 290 Page 3 EN 60169-23 : 1993 CONTENTS INTRODUCTION , . . . . . . . . . . ClauSe 1 scope _-.-.-*-.* 2 Dimensions - Mating face details for GPC and LPC connectors 2.1 Plug connector and contact . 2.2 Socket connector and c

12、ontact Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications . . . . . . . . . . . . . . . . . . = 3404583 0092826 127 H Page 4 EN 60169-23 : 1993 RADIO-FREQUENCY CONNECTORS Part 23: Pin and socket connector for use wi

13、th 3,5 mm rigid precision coaxial lines with inner diameter of outer conductor 33 mm (0,1378 in) INTRODUCTION This standard provides mating face details for the following two types of connectors: - GPC: General Precision Connector - Instrument grade (beaded). - LPC: Laboratory Precision Connector -

14、Instrument grade (beadless). 1 Scope Coaxial line devices and systems are becoming more prevalent at frequencies above 18 GHr. This standard covers a precision pin and socket connector for use with 33 mm rigid precision coaxial lines so as to minimize test apparatus errors attributable to coaxial co

15、nnectors. These connectors are constructed so as to affix on the 50 Q, 3,5 mm rigid precision coaxial line described in IEC 457-5, and to provide low reflection to 34 GHz. For mated pairs, a reflection factor of 0,003 + 0,00135f (GHr) is typical for QPC connectors. These connectors may be, and often

16、 are, mated with SMA connectors. 2 Dimensions - Mating face details for GPC and LPC connectors Original dimensions are in inches. All undimensioned pictorial configurations are for reference purposes only. m 3q04583 0092827 Ob3 m Page 5 EN 60169-23 : 1993 2.1 Plug connector and contact Reference pla

17、ne 0,013 I Note ? IEC 949l91 Dimensions in millimetres (inches) Figure 1 - Plug connector (for dimensions, see table 1 which follows) ab 71 Note 2 / I IDC 9-1 1 Dimensions in millimetres (inches) Figure 1 a - Plug contact (for dimensions, see table 1 which follows) Page 6 EN 60169-23 : 1993 = 340458

18、3 0092828 TTT 2.2 Socket connector and contact k- Reference plane Y Note 1 Dimensions in millimetres (inches) Figure 2 - Socket connector (for dimensions, see table 1 which follows) . (0,0005) Note 4 J Note 3 I. (Chamfer) Dimensions in millimetres (inches) Figure 2a - Socket contact (for dimensions,

19、 see table 1 which follows) Reference 8 b C d.q 49 e f B h h i k k I I i m.v m,v n P r O r S t U W X Y z ea m 3404583 0092829 936 m hge 7 EN 60169-23 : 1993 Table 1 - Dimensions Millimetres (mm) Min. 2,= 3.43 O.Oo0 0,000 6.38 4,547 0,03 3,493 3,495 0,919 0,15 2,w 2.41 no 20 1.514 1.51 61 534 3.35 0,

20、38 3,493 3,495 4,597 5.28 1 ,- 2,79 0,08 0.15 0.05 x 45“ 0,38 Max. 3s 2.49 4,Ol 0,076 0.013 6.73 4,577 0,13 3.508 3.505 0,935 038 229 2,67 33“ 250 1.524 1 ,5237 4.62 1.14 3,508 3,505 4,628 5.46 1,98 3,18 030 0.51 0.25 x 45“ 1.14 - Inches (in) Min. 0,093 O.OQQ 0.135 0,0000 0,0000 0,251 0,1790 0,001 0

21、,1375 0,1376 0,0362 0,006 0.080 O ,095 no 20“ 0,0596 0,05969 0.21 8 0,132 0.01 5 0,1375 0,1376 0,1810 0208 0,074 0,110 0,003 0,006 0,002 x 45“ 0.01 5 MiW. 0,135 0,098 0,158 0,0030 0,0005 0,265 O, 1802 0,005 0,1381 0,1380 0,0368 0,015 0,090 0,105 33O 25“ 0,- 0,05999 0,182 0,045 0,1381 0,1380 0.1822 0

22、,215 0,078 0.125 0,008 0,020 0,Ol o x 45O 0,045 - Connector GPC, GPC, GPC. GPC LPC GPC, GPC. GPC, GPC LPC GPC, GPC, GPC LPC GPC LPC GPC LPC GPC, GPC. GPC, GPC LPC GPC. GPC, GPC, GPC, GPC, GPC, GPC. GPC, LPC LPC LPC oniv dY LPC LPC LPC dY dY LPC LPC Miiv oniy 4Y OdY OdY dY LPC LPC LPC dY 4Y LPC LPC L

23、PC LPC LPC LPC LPC LPC NOTES 1 - Surface roughness 0.63 pm (16 pin). 2 - Surface roughness 1,26 pm (32 pin). 3 - Socket contact configuration (for example, slotted or slotless) optional; dimensions to meet reflection factor requirements, mating characteristics and connector durability when mated wit

24、h a 0,919 mm to 0,935 mm (0,0362 in to 0,0368 in) pin. Socket contact shall accept a 0,889 mm to 0,940 mm (0.0350 in to 0,0370 in) pin. 4 - To the left of dimension w (slotted contacts - GPC, LPC). bge 8 EN 60169-23 : 1993 Annex ZA (normative) Other international publications quoted in this standard

25、 with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references

26、, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTE. When the international publication has been modified by

27、CENELEC common modifications, indicated by (mod), the relevant EN/HD applies. IEC Publication Date Titie EN/HD Date 457-5 1984 Rigid precision coaxial lines and their HD 351.5 S1 1986 associated precision connectors rt 5: 50 ohm 3.5 mm rigid precision coaxal line with provision for wurunding connectors