ImageVerifierCode 换一换
格式:PDF , 页数:33 ,大小:1.19MB ,
资源ID:717755      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-717755.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(EN 60255-21-2-1995 en Electrical Relays Part 21 Vibration Shock Bump and Seismic Tests on Measuring Relays and Protection Equipment Section 2 Shock and Bump Tests《继电器 第21部分 测量继电器和保.pdf)为本站会员(fatcommittee260)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

EN 60255-21-2-1995 en Electrical Relays Part 21 Vibration Shock Bump and Seismic Tests on Measuring Relays and Protection Equipment Section 2 Shock and Bump Tests《继电器 第21部分 测量继电器和保.pdf

1、A BRITISH STANDARD Electrical relays Part 21. Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 2. Shock and bump tests The European Standard EN 60256-21-2 : 1995 has the status of a British Standard NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY

2、 COPYRIGHT LAW 3s EN 1996 1988 nColpM.ati?lg 50255-21-2 : EC 255-21-2 : 1mtNo. 1 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Services BSI BS*EN*b0255- 21-2 96 W 1624669 0561877 988 CENELEC members are bound to comply with the CENKENELEC Internal

3、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member

4、. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC m

5、embers are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit

6、 Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels I 1992 Copyright reserved to CENELEC members Ref. No. EN 60255-21-2 : 1995 E COPYRIGHT European Committee for Electrotechnical StandardizationLicensed

7、by Information Handling ServicesBSI BS*EN*b0255- 21-2 96 W 1624669 0561880 472 AEN 60256-21-2 : 1995 Issue 1, September 1996 Foreword The text of the International Standard Measuring relays and protection equipment, of IEC TC 41, Electrical relays, was submitted to the Unique Acceptance Procedure an

8、d was approved by CENELEC as EN 60255-21-2 on 1995-09-20 without any modification. The following dates were fixed: 1 IEC 255-21-2 : 1988, prepared by SC 41B), - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by - latest date by

9、 which the national standards conflicting with the EN have to be withdrawn endorsement (dp) 1996-10-01 (dow) 1996-10-01 Annexes designated normative are part of the body of the standard, appendix A and annex ZA are normative. Annex ZA has been added by CEWELEC. COPYRIGHT European Committee for Elect

10、rotechnical StandardizationLicensed by Information Handling ServicesA Issue 2. September 1996 .EN 60255-21-2 : 1995 CONTENTS Page National foreword Inside front cover Committees responsible Back cover Clause 1 Scope . 2 2 Object 2 3 Definitions . 2 3.1 Shock test 3 3.2 Shock response test 3 3.3 Shoc

11、k withstand test . 3 3.4 Bump test . 3 4 Requirements for shock and bump tests 3 4.1 Test apparatus and mounting . 3 4.2 Shock test severity classes . 5 4.3 Bump test severity classes . 6 4.4 Recommendations for the selection of shock and bump test severity classes . 7 4.5 Test procedure for shock r

12、esponse test . 7 4.6 Test procedure for shock withstand test and bump test . 9 5 Criteria for acceptance . 9 5.1 Acceptance criteria for shock response test 9 5.2 Acceptance criteria for shock withstand test and for bump test . 10 Figures . 11 Appendix A Selection criteria for shock and bump test pa

13、rameters a) and output circuit response during shock response test b) 13 Annex ZA (normative) Normative references to international publications with their corresponding European publications . 14 1 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Ser

14、vices255-21-2 0 IEC ELECTRICAL RELAYS Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment SECTION TWO - SHOCK AND BUMP TESTS 1. Scope This standard is part of a series specifying the vibration, shock, bump and seismic requirements applicable to electromecha

15、nical and static measuring relays and protection equipment with or without output contacts. This standard includes two types of test: - - the bump test (on non-energized specimen), the shock test (on energized and non-energized specimen); and is generally based on IEC 68-2-27 and 68-2-29. The requir

16、ements of this standard are applicable only to measuring relays and protection equipment in new condition. The tests specified in this standard are type tests. 2. Object The object of this standard is to state: - definitions of terms used; - test conditions; - standard test severity classes; - test

17、procedure; - criteria for acceptance. 3. Definitions For definitions of general terms not defined in this standard, reference should be made to: - International Electrotechnical Vocabulary (IEV) IEC 501 ; - IEC 68-2-27 and 68-2-29; - relay standards published in the IEC 255 series; - IS0 2041; - Sec

18、tion One: Vibration tests (sinusoidal) IEC 255-21-11. For the purpose of this standard the following definitions shall apply: 2 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling ServicesBSI BS*EN*hO255- 21-2 96 I1624669 0562883 I182 255-21-2 0 IEC 3.1

19、Shock test A test during which a specimen, non-energized or energized under specified conditions, is subjected to a limited number of single shocks, in the three different axes of the specimen in turn, to determine its capability to withstand the effects of shocks. Note.- The term “specimen“ include

20、s any auxiliary part which is an integral functional feature of the measuring relay or protec- tion equipment under test. 3.2 Shock response test A shock test carried out on a measuring relay or protection equip- ment, energized under specified conditions, to determine its response to shocks likely

21、to be occasionally encountered in service. 3.3 Shock withstand test A high level shock test carried out on a non-energized measuring relay or protection equipment to determine its capability to withstand shocks likely to be occasionally encountered during transportation and handling. 3.4 Bump test A

22、 test during which a non-energized measuring relay or protection equipment is subjected to a limited number of bumps, in three different axes of the specimen in turn, to determine its capability to withstand thP effects of bumps iikely to be encountered during trans- portation. 4. Requirements for s

23、hock and bump tests The main parameters of the shock and bump tests are the following: - acceleration; - - number of pulses applied. duration of the nominal pulse; In this standard the pulse shape used is one half-cycle of a sine wave. 4.1 Test apparatus and mounting The required characteristics of

24、the shock and bump generators and fixtures together with the mounting requirements shall be as specified in the following sub-clauses. The characteristics shall apply when the specimen is mounted on the generator. 4.1 . 1 Acceleration tolerances The nominal pulse shape for shock and bump tests shall

25、 be one half-cycle of a sine wave, as indicated by the dotted line shown in Figure 1. 3 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Services i BSI BS*EN*b0255- 21-2 96 = II624669 056IIBB4 OLB value of the actual acceleration shall be within the t

26、oler- ndicated by the solid lines shown in Figure 1. 255-21-2 0 IEC The true ance limits 4.1 .2 Pulse dL :ation tolerances The actual pulse duration shall be the nominal value within a toler- ance of +2 ms. 4.1 .3 Transverse motion The positive or negative peak acceleration at the monitoring point,

27、perpendicular to the intended shock or bump direction, shall not exceed, at any time, 30% of the value of the peak acceleration of the nominal pulse in the intended direction, when determined by a measur- ing system in accordance with Sub-clause 4.1.5. 4.1 .4 Repetition rate During shock and bump te

28、sts, the repetition rate shall be such that between applied pulses the relative motion within the specimen shall be substantially zero and the value of acceleration at the reference point shall be within the limits shown in Figure 1. Note.- For the bump test a rate of one to three pulses per second

29、is usually adequate. 4.1 .5 Measuring system The shock and bump pulse shall be measured by an accelerometer placed at the reference point, which shall be declared by the manu- facturer. The characteristics of the measuring system shall be such that it can be determined that the true value of the act

30、ual pulse, as measured in the intended direction at the reference point, is within the tolerances required by the Sub-clauses 4.1.1 and 4.1.2. The frequency response of the overall measuring system, including the accelerometer, can have a significant effect on the accuracy and shall be within the li

31、mits shown in Figure 2 for shock and bump tests. 4.1.6 Mounting The specimen shall be fastened to the shock or bump generator or fixture by its normal means of attachment in service, such that the gravitational force acts on it in the same relative direction as it would in normal use. During the sho

32、ck response test, cable connections to the specimen shall be so arranged that they impose no more restraint or mass than they would when the specimen is installed in its operating position. Note.- Care should be taken to ensure that the specimen under test is not significantly affected by any magnet

33、ic field generated by the test system. 4 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Services BSI BS*EN*b0255- 21-2 96 9 II624669 0561885 T54 9 255-21-2 O IEC Class O 1 2 4.2 Shock test severity classes Peak Duration D Number of pulses accelerati

34、on A of the pulse in each direction gn) ms) - - - 5 11 3 Yk XO 11 3Yk This standard includes two types of shock tests: - shock response test on an energized relay or protection equipment; - shock withstand test on a non-energized relay or protection equipment . Both shock response test and shock wit

35、hstand test include three different severity classes (O, 1, 2) the main parameters of which are referred to in Sub-ciauses 4.2.1 and 4.2.2 below. For particular types of measuring relays or protection equipment, the manufacturer may declare different severity classes for shock response test and shoc

36、k withstand test. When Class O is declared, no shock tests apply. 4.2.1 Shock repponse test This test is applied to an energized measuring relay or protection eq u ipmen t. The parameters for the test are given in Table I for the different severity classes. TABLE I Shock response test parameters for

37、 different severity classes (see Appendix A, Item a) * Three pulses in each direction correspond to six pulses in each axis. 4.2.2 Shock withstand test This test is applied to a non-energized measuring relay or protection equipment. 5 COPYRIGHT European Committee for Electrotechnical Standardization

38、Licensed by Information Handling Services BSI BSsENUb0255- 2L-2 96 m Lb24bb9 05b3b 990 m 255-21-2 0 IEC Class The parameters for the test are given in Table II for the different severity classes. Peak acceleration A (gn) TABLE II Shock withstand test parameters for different severity classes Peak Du

39、ration D Class acceleration A of the pulse (gn) (ms) - - O 1 10 16 2 20 16 Number of pulses in each direction - 1 ooo* 1 ooo* I I Duration D of the pulse ms) 11 1. 1 ,k Three pulses in each direction correspond axis. 4.3 Bump test severity classes Number of pulses in each direction 3* to six pulses

40、in each This test is applied to a non-energized measuring relay or protection equipment . This standard includes, for the bump test, three different severity classes (O, 1, 2) the main parameters of which are referred to in Table I I I below. When Class O is declared, no bump test applies. TABLE III

41、 6 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Handling Services- i ES1 BS*EN*b0255- 21-2 96 Lb24669 0561887 827 255-21-2 0 IEC 4.4 Recommendations for the selection of shock and bump test severity classes The test severities are classified with respect t

42、o the ability of a measuring relay or protection equipment to withstand the mechanical shocks and bumps likely to be experienced in a particular transpor- tation or type of use, in accordance with Table IV below. TABLE IV Cuide for selection of test severity classes Class Typical applications I ther

43、e are no shock and bump requirements Measuring relays and protection equipment for which 1 2 Measuring relays and protection equipment for normal use in power plants, substations and industrial plants and for normal transportation conditions” Measuring relays and protection equipment for which a ver

44、y high security margin is required or where the shock and bump levels are very high, e.g. shipboard application and for severe transportation conditions* k The packaging of the measuring relay or protection equipment should be designed and implemented in such a manner that the severity class paramet

45、ers will not be exceeded during transportation. 4.5 Test procedure for shock response test The shock pulse characteristics shall be measured at the reference point, which shall be declared by the manufacturer. Note.- If the size of a specimen makes it impracticable to test it as a whole, it may be t

46、ested as functional sub-units as agreed between manufacturer and user. During the test, the specimen shall be in its case with the cover, if any, in position. Any transportation restraints shall be removed. 7 COPYRIGHT European Committee for Electrotechnical StandardizationLicensed by Information Ha

47、ndling Services- ._ BSI BS*EN*b0255- 2L-2 96 Lb24bb9 05bL 7b3 255-21-2 0 IEC 4.5.1 During the test, three successive pulses shall be applied in each direction of the three mutually perpendicular axes of the specimen in turn (a total of 18 pulses). The peak acceleration shall be as specified in Table

48、 I for the declared severity class. 4.5.2 The test shall be carried out on a measuring relay or protection equipment under reference conditions stated in the relevant relay standard, published in the IEC 255 series, and with the following values of energizing quantities (auxiliary and input) and loa

49、ding applied to the appropriate circuits: - auxiliary energizing quantity(ies) : rated value(s); - output circuit loadings: no loading except the monitoring devices or loading as declared by the manufacturer; - input energizing quantity(ies) : values equal to the operating value of the characteristic quantity plus and minus the manufacturers declared variation for no maloperation due to shocks, see Items a) and b) below. a) The value of the characteristic quantity shall be below the operating value for maximum measuring relay or protection

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1