EN 60317-13-2010 en Specifications for particular types of winding wires - Part 13 Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire class 200.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wiresPart 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200BS EN 60317-13:2010

2、National forewordThis British Standard is the UK implementation of EN 60317-13:2010. It isidentical to IEC 60317-13:2010. It supersedes BS EN 60317-13:1995 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations repr

3、esented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 67177 7ICS 29.060.10Compliance with a British Standard cannot confer

4、immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 June 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60317-13:2010EUROPEAN STANDARD EN 60317-13 NORME EUROPENNE EUROPISC

5、HE NORM May 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any me

6、ans reserved worldwide for CENELEC members. Ref. No. EN 60317-13:2010 E ICS 29.060.10 Supersedes EN 60317-13:1994 + A1:1997 + A2:1998English version Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire

7、, class 200 (IEC 60317-13:2010) Spcifications pour types particuliers de fils de bobinage - Partie 13: Fil de section circulaire en cuivre maill avec polyester ou polyesterimide et avec surcouche polyamide-imide, classe 200 (CEI 60317-13:2010) Technische Lieferbedingungen fr bestimmte Typen von Wick

8、eldrhten - Teil 13: Runddrhte aus Kupfer, lackisoliert mit Polyester oder Polyesterimid und darber mit Polyamidimid, Klasse 200 (IEC 60317-13:2010) This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

9、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard

10、 exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national

11、electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

12、weden, Switzerland and the United Kingdom. BS EN 60317-13:2010EN 60317-13:2010 - 2 - Foreword The text of document 55/1179/FDIS, future edition 3 of IEC 60317-13, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-13 on 2010-0

13、5-01. This European Standard supersedes EN 60317-13:1994 + A1:1997 + A2:1998. The main changes with respect to EN 60317-13:1994 and its amendments are listed below: new requirements for appearance; reference to new resistance to refrigerants test in IEC 60851-4; deletion of high temperature failure

14、requirement; new pin hole test requirements. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date

15、by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-02-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-05-01 Annex ZA has been added by CENELEC. _ Endorsement noti

16、ce The text of the International Standard IEC 60317-13:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60317-13:2010- 3 - EN 60317-13:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The

17、following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modif

18、ied by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-1 2008 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire EN 60317-0-1 2008 IEC 60851-4 + A1 + A2 1996 1997 2005

19、 Winding wires - Test methods - Part 4: Chemical properties EN 60851-4 + A1 + A2 1996 1997 2005 BS EN 60317-13:2010 2 60317-13 IEC:2010 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms, definitions and general notes on methods of test and appearance 6 3.1 Terms and definitions 6 3

20、.2 General notes on methods of test7 3.3 Appearance.7 4 Dimensions 7 5 Electrical resistance .7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence7 9 Heat shock .7 10 Cut-through 7 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,500 mm) .7 12 Resist

21、ance to solvents8 13 Breakdown voltage .8 14 Continuity of insulation .8 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .9 18 Heat or solvent bonding9 19 Dielectric dissipation factor.9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin hole test .9 30 Packaging 9

22、Table 1 Resistance to abrasion8 BS EN 60317-13:201060317-13 IEC:2010 5 INTRODUCTION This Part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires and methods of test (IEC 60851) ; 2) speci

23、fications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-13:2010 6 60317-13 IEC:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class

24、 200 1 Scope This Part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and mee

25、ts all specified wire requirements. The superimposed coating is based on polyamide-imide resin. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 200 is a thermal class that re

26、quires a minimum temperature index of 200 and a heat shock temperature of at least 220 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of

27、 equipment involved. The range of a nominal conductor diameters covered by this standard is as follows: Grade 1: 0,050 mm up to and including 2,000 mm; Grade 2: 0,050 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1. 2 Normative references T

28、he following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1:2008, Specifications for particular

29、types of winding wires Part 0-1: General requirements Enamelled round copper wire IEC 60851-4:1996, Methods of test for winding wires Part 4: Chemical properties Amendment 1 (1997) Amendment 2 (2005) 3 Terms, definitions and general notes on methods of test and appearance 3.1 Terms and definitions F

30、or terms and definitions, see 3.1 of IEC 60317-0-1. In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 60317-13 shall prevail. BS EN 60317-13:201060317-13 IEC:2010 7 3.2 General notes on methods of test For general notes on methods of test, see 3.2 of IEC 60317-0-1. In case of i

31、nconsistencies between IEC 60317-0-1 and this standard, IEC 60317-13 shall prevail. 3.3 Appearance See 3.3 of IEC 60317-0-1. 4 Dimensions See Clause 4 of IEC 60317-0-1. 5 Electrical resistance See Clause 5 of IEC 60317-0-1. 6 Elongation See Clause 6 of IEC 60317-0-1. 7 Springiness See Clause 7 of IE

32、C 60317-0-1. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-1, where the constant K used for the calculation of the number of revolutions for the peel test shall be 110 mm. 9 Heat shock See Clause 9 of IEC 60317-0-1, where the minimum heat shock temperature shall be 220 C. 10 Cut-through No

33、 failure shall occur within 2 min at 320 C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,500 mm) The wire shall meet the requirements given in Table 1. BS EN 60317-13:2010 8 60317-13 IEC:2010 Table 1 Resistance to abrasion Grade 1 Grade 2 Nominal conduct

34、or diameter mm Minimum average force to failure N Minimum force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,250 0,280 0,315 0,355 0,400 3,00 3,25 3,50 3,75 4,05 2,55 2,75 2,95 3,20 3,45 4,90 5,25 5,65 6,05 6,50 4,15 4,45 4,80 5

35、,15 5,50 0,450 0,500 0,560 0,630 0,710 4,35 4,65 5,00 5,35 5,70 3,70 3,95 4,25 4,55 4,85 7,00 7,50 8,00 8,60 9,20 5,90 6,35 6,80 7,30 7,80 0,800 0,900 1,000 1,120 1,250 6,10 6,55 7,05 7,60 8,20 5,15 5,55 5,95 6,45 6,95 9,90 10,6 11,3 12,1 12,9 8,40 9,00 9,60 10,2 11,0 1,400 1,600 1,800 2,000 2,240 8

36、,80 9,45 10,1 10,9 7,45 8,00 8,60 9,20 13,9 14,9 16,0 17,1 18,2 11,8 12,6 13,5 14,4 15,4 2,500 19,4 16,4 For intermediate nominal conductor diameters, the value of the next largest nominal conductor diameter shall be taken. 12 Resistance to solvents See Clause 12 of IEC 60317-0-1. 13 Breakdown volta

37、ge See Clause 13 of IEC 60317-0-1, where the elevated temperature shall be 200 C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-1. 15 Temperature index See Clause 15 of IEC 60317-0-1, where the minimum temperature index shall be 200. 16 Resistance to refrigerants When tested according to

38、IEC 60851-4, Clause 4, the percentage of extractable matter shall not exceed 0,5 %. The requirement for breakdown voltage shall be 75 % of the minimum specified value. BS EN 60317-13:201060317-13 IEC:2010 9 17 Solderability Test inappropriate. 18 Heat or solvent bonding Test inappropriate. 19 Dielec

39、tric dissipation factor Test inappropriate. 20 Resistance to transformer oil Test appropriate but no requirements specified. 21 Loss of mass Test inappropriate. 23 Pin hole test See Clause 23 of IEC 60317-0-1. 30 Packaging See Clause 30 of IEC 60317-0-1. _ BS EN 60317-13:2010This page deliberately l

40、eft blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Cha

41、rter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendme

42、nts or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be foun

43、d on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou m

44、ay buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to o

45、rders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledg

46、e Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelo

47、pments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can b

48、e found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse,