EN 60317-56-2017 en Specifications for particular types of winding wires - Part 56 Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire class 180.pdf

1、Specifications for particular types of winding wiresPart 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)BS EN 60317-56:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME

2、 EUROPENNE EUROPISCHE NORM EN 60317-56 October 2017 ICS 29.060.10 Supersedes EN 60317-56:2012 English Version Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017) Spcificat

3、ions pour types particuliers de fils de bobinage - Partie 56: Fil brasable de section circulaire, isol en continu, en cuivre maill avec polyurthane sans dfaut lectrique, classe 180 (IEC 60317-56:2017) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 56: Isolationsfehlerfreie R

4、unddrhte (FIW) aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180 (IEC 60317-56:2017) This European Standard was approved by CENELEC on 2017-09-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipula

5、te the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European

6、 Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC member

7、s are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norwa

8、y, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre:

9、 Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60317-56:2017 E National forewordThis British Standard is the UK implementation of EN 60317-56:2017. It is identical to IEC 60317-56:2017. It su

10、persedes BS EN 60317-56:2012, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee L/-/99, Miscellaneous Standards - Electrical.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpo

11、rt to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 92424 8ICS 29.060.10Compliance with a British Standard cannot confer immunity from legal obligatio

12、ns.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 6031756:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60317-56 October 2017 I

13、CS 29.060.10 Supersedes EN 60317-56:2012 English Version Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017) Spcifications pour types particuliers de fils de bobinage - Pa

14、rtie 56: Fil brasable de section circulaire, isol en continu, en cuivre maill avec polyurthane sans dfaut lectrique, classe 180 (IEC 60317-56:2017) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 56: Isolationsfehlerfreie Runddrhte (FIW) aus Kupfer, verzinnbar, lackisoliert m

15、it Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180 (IEC 60317-56:2017) This European Standard was approved by CENELEC on 2017-09-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard t

16、he status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English,

17、 French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Aus

18、tria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slove

19、nia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All r

20、ights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60317-56:2017 E BS EN 6031756:2017EN 60317-56:2017 2 European foreword The text of document 55/1616/FDIS, future edition 2 of IEC 60317-56, prepared by IEC/TC 55 “Winding wires“ was submitted to th

21、e IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-56:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-06-13 latest date by which the national stan

22、dards conflicting with the document have to be withdrawn (dow) 2020-09-13 This document supersedes EN 60317-56:2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all

23、such patent rights. Endorsement notice The text of the International Standard IEC 60317-56:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 (series) NOT

24、E Harmonized as EN 60264 (series). IEC 60317 (series) NOTE Harmonized as EN 60317 (series). IEC 60851 (series) NOTE Harmonized as EN 60851 (series). BS EN 6031756:2017EN 60317-56:2017 2 European foreword The text of document 55/1616/FDIS, future edition 2 of IEC 60317-56, prepared by IEC/TC 55 “Wind

25、ing wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-56:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-06-13 latest d

26、ate by which the national standards conflicting with the document have to be withdrawn (dow) 2020-09-13 This document supersedes EN 60317-56:2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsib

27、le for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-56:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards ind

28、icated: IEC 60264 (series) NOTE Harmonized as EN 60264 (series). IEC 60317 (series) NOTE Harmonized as EN 60317 (series). IEC 60851 (series) NOTE Harmonized as EN 60851 (series). EN 60317-56:2017 3 Annex ZA (normative) Normative references to international publications with their corresponding Europ

29、ean publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

30、mendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Y

31、ear Title EN/HD Year IEC 60317-0-7 - FprEN 60317-0-7 - BS EN 6031756:2017This page deliberately left blank 2 IEC 60317-56:2017 IEC 2017 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions, general notes and appearance . 6 3.1 Terms and definitions 6 3.2

32、General notes . 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance 7 4 Dimensions 7 5 Electrical resistance 7 6 Elongation . 7 7 Springiness . 7 8 Flexibility and adherence . 7 9 Heat shock 7 10 Cut-through . 7 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and includi

33、ng 0,900 mm) . 7 12 Resistance to solvents . 8 13 Breakdown voltage 8 14 Continuity of insulation 8 15 Temperature index 8 16 Resistance to refrigerants 8 17 Solderability 8 18 Heat or solvent bonding . 9 19 Dielectric dissipation factor 9 20 Resistance to transformer oil . 9 21 Loss of mass . 9 23

34、Pin-hole test 9 30 Packaging . 9 Annex A (informative) Resistance to abrasion 10 A.1 Grades of FIW 3, 5, 7, 9 10 A.2 Grades 3 through 9 . 10 Bibliography 11 Table 1 Resistance to abrasion 8 Table A.1 Resistance to abrasion of FIW grades 3 through 9 . 10 2 IEC 60317-56:2017 IEC 2017 CONTENTS FOREWORD

35、 . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions, general notes and appearance . 6 3.1 Terms and definitions 6 3.2 General notes . 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance 7 4 Dimensions 7 5 Electrical resistance 7 6 Elongation . 7 7 Springiness .

36、 7 8 Flexibility and adherence . 7 9 Heat shock 7 10 Cut-through . 7 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including 0,900 mm) . 7 12 Resistance to solvents . 8 13 Breakdown voltage 8 14 Continuity of insulation 8 15 Temperature index 8 16 Resistance to refrigerants

37、8 17 Solderability 8 18 Heat or solvent bonding . 9 19 Dielectric dissipation factor 9 20 Resistance to transformer oil . 9 21 Loss of mass . 9 23 Pin-hole test 9 30 Packaging . 9 Annex A (informative) Resistance to abrasion 10 A.1 Grades of FIW 3, 5, 7, 9 10 A.2 Grades 3 through 9 . 10 Bibliography

38、 11 Table 1 Resistance to abrasion 8 Table A.1 Resistance to abrasion of FIW grades 3 through 9 . 10 BS EN 6031756:2017IEC 60317-56:2017 IEC 2017 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 56: Solderable fully insulated (FIW) zero-defect p

39、olyurethane enamelled round copper wire, class 180 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation

40、 on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

41、 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparati

42、on. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus

43、 of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are m

44、ade to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications trans

45、parently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent c

46、ertification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability

47、 shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including

48、 legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this

49、 publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-56 has been prepared by IEC technical committee 55: Winding wires. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical ch