EN 60371-3-5-2006 en Insulating materials based on mica Part 3 Specifications for individual materials Sheet 5 Glass-backed mica paper with an epoxy resin binder for post-impregnat.pdf

1、BRITISH STANDARDBS EN60371-3-5:2006Insulating materials based on mica Part 3: Specifications for individual materials Sheet 5: Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI)The European Standard EN 60371-3-5:2006 has the status of a British StandardICS 29.035.10; 29.0

2、35.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60371-3-5:2006This British Standard was published under the authority of the Standards Po

3、licy and Strategy Committee on 31 March 2006 BSI ISBN 0 580 47968 4National forewordThis British Standard is the official English language version of EN 60371-3-5:2006. It is identical with IEC 60371-3-5:2005. It supersedes BS EN 60371-3-5:1996 which is withdrawn. The UK participation in its prepara

4、tion was entrusted to Technical Committee GEL/15, Standards on specifications for electrical insulating materials, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement

5、international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not

6、purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European comm

7、ittee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an

8、 inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 60371-3-5 NORME EUROPENNE EUROPISCHE NORM February 2006 CENELEC European Committee for Ele

9、ctrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref

10、. No. EN 60371-3-5:2006 E ICS 29.035.10; 29.035.50 Supersedes EN 60371-3-5:1995English version Insulating materials based on mica Part 3: Specifications for individual materials Sheet 5: Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI) (IEC 60371-3-5:2005) Matriaux isol

11、ants base de mica Partie 3: Spcifications pour matriaux particuliers Feuille 5: Papier de mica renforc de verre avec un agglomrant en rsine poxyde pour post-imprgnation (VPI) (CEI 60371-3-5:2005) Isoliermaterialien aus Glimmer Teil 3: Bestimmungen fr einzelne Materialien Blatt 5: Glimmerpapier mit e

12、inem Glasgewebetrger mit einem Epoxidkleber zur Vakuumimprgnierung (VPI) (IEC 60371-3-5:2005) This European Standard was approved by CENELEC on 2005-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard t

13、he status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, G

14、erman). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cypru

15、s, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 60371-3-5:2006 Foreword The

16、 text of document 15/228/FDIS, future edition 2 of IEC 60371-3-5, prepared by IEC TC 15, Standards on specifications for electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60371-3-5 on 2005-12-01. This European Standard supersedes EN 603

17、71-3-5:1995. The main changes with regard to EN 60371-3-5:1995 include adjustments to align this standard with changes included in the latest edition of EN 60371-2. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical nati

18、onal standard or by endorsement (dop) 2006-09-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-12-01 This European Standard makes reference to International Standards. Where the International Standard referred to has been endorsed as a European S

19、tandard or a home-grown European Standard exists, this European Standard shall be applied instead. Pertinent information can be found on the CENELEC web site. _ Endorsement notice The text of the International Standard IEC 60371-3-5:2005 was approved by CENELEC as a European Standard without any mod

20、ification. _ 2 3 EN 60371-3-5:2006 CONTENTS INTRODUCTION.4 1 Scope 5 2 Normative references .5 3 Designation 5 4 Requirements: raw materials.7 4.1 Mica paper 7 4.2 Glass fabric.7 4.3 Epoxy resin .7 5 Requirements: composition and tolerances .7 6 Requirements for material (as received)8 6.1 General .

21、8 6.2 Width 8 6.3 Thickness8 6.4 Length.8 6.5 Cores 8 6.6 Joins .9 6.7 Tensile strength in the warp direction.9 6.8 Stiffness9 6.9 Air permeance .9 7 Packing9 Table 1 Composition low bond, with a resin content in the range (8 3) %6 Table 2 Composition medium bond, with a resin content in the range (

22、16 3) % .7 Table 3 Tolerance on width 8 Table 4 Air porosity9 EN 60371-3-5:2006 4 This part of IEC 60371 forms part of a series which deals with insulating materials built up from mica splittings or mica paper with or without reinforcement, and with mica paper in its pure state for use in electrical

23、 equipment IEC 60371 consists of three parts under the main title Specification for insulating materials based on mica: Part 1: Definitions and general requirements Part 2: Methods of test Part 3: Specifications for individual materials This standard contains one of the sheets comprising part 3, as

24、follows: Sheet 5: Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI vacuum pressure impregnation) INTRODUCTION 5 EN 60371-3-5:2006 INSULATING MATERIALS BASED ON MICA Part 3: Specifications for individual materials Sheet 5: Glass-backed mica paper with an epoxy resin binde

25、r for post-impregnation (VPI) 1 Scope This part of IEC 60371 gives requirements for electrical insulating materials made by combining mica paper with glass fabric and bonding them together with a small amount of epoxy resin. The material is supplied in a flexible state and is designed for use in con

26、junction with vacuum pressure impregnation (VPI) with compatible impregnates. The final cured properties will be primarily dependent on the VPI resin used. Two bond contents are specified: low bond with a resin content of (8 3) %; medium bond with a resin content of (16 3) %. Materials which conform

27、 to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2 Normative references

28、 The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60371-2:2004, Specification for insulating m

29、aterials based on mica Part 2: Methods of test IEC 60371-3-2, Insulating materials based on mica Part 3: Specifications for individual materials Sheet 2: Mica paper ISO 5636-5:2003, Paper and board Determination of air permeance and air resistance (medium range) Part 5: Gurley method 3 Designation W

30、hen ordering materials to this specification only the specification and type numbers need be quoted (see Tables 1 and 2). Example: IEC 60371-3-5: type 5.1.01 The type number is derived from: the specification sheet number 5 plus the sheet table number 5.1 plus the number of the product in the sheet

31、table 5.1.01 EN 60371-3-5:2006 6 The descriptive code quoted in Tables 1 and 2, for example G23/M80/R08 for type 5.1.01, Table 1, is derived from: glass content (G) 23 g/m muscovite mica content (M) 80 g/m resin content (R) 8 3 %. NOTE For phlogopite mica paper the letter “M“ is replaced by the lett

32、er “P“. Table 1 Composition low bond, with a resin content in the range (8 3) % Glass content g/m2Mica content g/m2Mass/ unit area g/m2Permissable thickness range mm Type Descriptive code Nom. Tol.r Nom. Tol.r Nom. Tol.r Mean Individual Volatile content max. % 5.1.01 G23/M80/R08 23 2 80 7 112 12 0,0

33、8-0,12 0,07-0,13 0,5 5.1.02 G23/P80/R08 23 2 80 7 112 12 0,08-0,12 0,07-0,13 0,5 5.1.03 G23/M120/R08 23 2 120 10 155 15 0,09-0,13 0,08-0,14 0,5 5.1.04 G23/P120/R08 23 2 120 10 155 15 0,09-0,13 0,08-0,14 0,5 5.1.05 G32/M120/R08 32 3 120 10 165 17 0,10-0,14 0,09-0,15 0,5 5.1.06 G32/P120/R08 32 3 120 1

34、0 165 17 0,10-0,14 0,09-0,15 0,5 5.1.07 G23/M160/R08 23 2 160 13 199 20 0,11-0,16 0,10-0,17 0,5 5.1.08 G23/P160/R08 23 2 160 13 199 20 0,11-0,16 0,10-0,17 0,5 5.1.09 G32/M160/R08 32 3 160 13 209 21 0,12-0,17 0,11-0,18 0,5 5.1.10 G32/P160/R08 32 3 160 13 209 21 0,12-0,17 0,11-0,18 0,5 5.1.11 G23/M180

35、/R08 23 2 180 14 220 22 0,13-0,18 0,12-0,19 0,5 5.1.12 G23/P180/R08 23 2 180 14 220 22 0,13-0,18 0,12-0,19 0,5 5.1.13 G32/M180/R08 32 3 180 14 231 23 0,14-0,19 0,13-0,20 0,5 5.1.14 G32/P180/R08 32 3 180 14 231 23 0,14-0,19 0,13-0,20 0,5 5.1.15 G23/M250/R08 23 2 250 20 297 30 0,16-0,21 0,15-0,22 0,5

36、5.1.16 G23/P250/R08 23 2 250 20 297 30 0,16-0,21 0,15-0,22 0,5 5.1.17 G32/M250/R08 32 3 250 20 307 31 0,17-0,22 0,16-0,23 0,5 5.1.18 G32/P250/R08 32 3 250 20 307 31 0,17-0,22 0,16-0,23 0,5 7 EN 60371-3-5:2006 Table 2 Composition medium bond, with a resin content in the range of (16 3) % Glass conten

37、t g/m2Mica content g/m2Mass/ unit area g/m2Permissable thickness range mm Type Descriptive code Nom. Tol.r Nom. Tol.r Nom. Tol.r Mean Individual Volatile content max. % 5.2.01 G23/M120/R16 23 2 120 10 170 17 0,10-0,14 0,09-0,15 0,5 5.2.02 G23/P120/R16 23 2 120 10 170 17 0,10-0,14 0,09-0,15 0,5 5.2.0

38、3 G32/M120/R16 32 3 120 10 181 18 0,12-0,16 0,11-0,17 0,5 5.2.04 G32/P120/R16 32 3 120 10 181 18 0,12-0,16 0,11-0,17 0,5 5.2.05 G23/M160/R16 23 2 160 13 218 22 0,12-0,17 0,11-0,18 0,5 5.2.06 G23/P160/R16 23 2 160 13 218 22 0,12-0,17 0,11-0,18 0,5 5.2.07 G32/M160/R16 32 3 160 13 229 23 0,14-0,19 0,13

39、-0,20 0,5 5.2.08 G32/P160/R16 32 3 160 13 229 23 0,14-0,19 0,13-0,20 0,5 5.2.09 G23/M180/R16 23 2 180 14 242 24 0,14-0,19 0,13-0,20 0,5 5.2.10 G23/P180/R16 23 2 180 14 242 24 0,14-0,19 0,13-0,20 0,5 5.2.11 G32/M180/R16 32 3 180 14 253 26 0,16-0,21 0,15-0,22 0,5 5.2.12 G32/P180/R16 32 3 180 14 253 26

40、 0,16-0,21 0,15-0,22 0,5 5.2.13 G23/M250/R16 23 2 250 20 325 33 0,17-0,22 0,16-0,23 0,5 5.2.14 G23/P250/R16 23 2 250 20 325 33 0,17-0,22 0,16-0,23 0,5 5.2.15 G32/M250/R16 32 3 250 20 336 34 0,19-0,24 0,18-0,25 0,5 5.2.16 G32/P250/R16 32 3 250 20 336 34 0,19-0,24 0,18-0,25 0,5 4 Requirements: raw mat

41、erials 4.1 Mica paper Mica paper referred to in this specification shall comply with the requirements of IEC 60371-3-2. 4.2 Glass fabric Normally the glass fabric shall be continuous filament glass fibre made from E glass. Unless otherwise agreed to between purchaser and seller, the glass fibre shal

42、l be in the loom state and have a size content not greater than 3 % by weight. For some applications a special type of size may be necessary and any requirements shall be subject to the purchase contract. 4.3 Epoxy resin Any epoxy resin system may be used which enables the material to meet the requi

43、rements of this specification. 5 Requirements: composition and tolerances When tested by the method of Clause 7 of IEC 60371-2 the composition of the products shall lie within the limits of Tables 1 and 2 for the appropriate grade of mica paper. EN 60371-3-5:2006 8 6 Requirements for material (as re

44、ceived) 6.1 General All materials in any one consignment shall have the same properties, within the limits of this specification, throughout the length of each roll. The surfaces shall be uniform and free from defects such as bubbles, pin-holes, creases and flaws. Material supplied in rolls shall be

45、 capable of being unrolled continuously without damage, and the force required to unroll the material shall be substantially uniform. The material shall be supplied non-interleaved. Unless otherwise specified in the purchase contract the material shall be rolled with the mica surface on the outside.

46、 6.2 Width This specification contains no requirement for width of tape. However, the following widths are preferred: 10, 12, 15, 20, 25, 30, 40 and 50 mm. The maximum trimmed width of full width material and sheet normally available is 1 000 mm. The tolerance on the width of the material shall be a

47、s in Table 3. Table 3 Tolerance on width Nominal width mm Tolerance mm d 20 20 d 500 500 0,5 1,0 5,0 6.3 Thickness Measure the thickness in accordance with Clause 4 of IEC 60371-2, using the apparatus given in 4.1.1 of that standard, making 10 measurements on one thickness of material. The measured

48、values shall be in accordance with the requirements of Tables 1 and 2. 6.4 Length There is no requirement in this specification for roll length, and this shall therefore be subject to the purchase contract. For sheet material, the tolerance on length shall be the same as for width. 6.5 Cores The tap

49、e shall be supplied compactly wound on cores of 25 mm, 40 mm, 55 mm, or 76 mm inside diameter which shall be free from sharp edges. The width of the cores in relation to that of the tape shall be subject to the purchase contract. Full width material and material wider than 100 mm shall be supplied on 55 mm or 76 mm cores. 9 EN 60371-3-5:2006 6.6 Joins The number of rolls with joins shall be limited to 25 % of any one consignment. Joine