EN 60384-13-2012 en Fixed capacitors for use in electronic equipment - Part 13 Sectional specification - Fixed polypropylene film dielectric metal foil d c capacitors《电子设备用固定电容器 第1.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFixed capacitors for use in electronic equipmentPart 13: Sectional specification Fixed polypropylene film dielectric metal foil d.c. capacitorsBS EN 60384-13:2012National forewor

2、dThis British Standard is the UK implementation of EN 60384-13:2012. It isidentical to IEC 60384-13:2011. It supersedes BS EN 60384-13:2006 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeEPL/40X, Capacitors and resistors for electronic equipment.A list

3、of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limite

4、d 2012ISBN 978 0 580 70455 0ICS 31.060.30 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 April 2012.Amendments issued since publicationAmd. No. Date Text affec

5、tedBRITISH STANDARDBS EN 60384-13:2012EUROPEAN STANDARD EN 60384-13 NORME EUROPENNE EUROPISCHE NORM March 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Ma

6、rnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-13:2012 E ICS 31.060.30 Supersedes EN 60384-13:2006 + corr. Nov.2006English version Fixed capacitors for use in electronic equipment - Part 13:

7、Sectional specification - Fixed polypropylene film dielectric metal foil d.c. capacitors (IEC 60384-13:2011) Condensateurs fixes utiliss dans les quipements lectroniques - Partie 13: Spcification intermdiaire - Condensateurs fixes pour courant continu dilectrique en film de polypropylne armatures en

8、 feuilles mtalliques (CEI 60384-13:2011) Festkondensatoren zur Verwendung in Gerten der Elektronik - Teil 13: Rahmenspezifikation - Festkondensatoren mit einem Dielektrikum aus Polypropylen und Belgen aus Metallfolien fr Gleichspannung (IEC 60384-13:2011) This European Standard was approved by CENEL

9、EC on 2012-01-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard

10、s may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language a

11、nd notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irelan

12、d, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60384-13:2012EN 60384-13:2012 - 2 - Foreword The text of document 40/2130/FDIS, future edition 4 of IEC 60384-13, p

13、repared by IEC TC 40, “Capacitors and resistors for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60384-13:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identica

14、l national standard or by endorsement (dop) 2012-10-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-01-13 This document supersedes EN 60384-13:2006 + corr. nov. 2006. EN 60384-13:2012 includes the following significant technical changes wi

15、th respect to EN 60384-13:2006: Table 3, Sampling plan together with numbers of permissible non-conformance for qualification approval test, has been adjusted. Table 5, Lot-by-lot inspection, has been changed, highlighting assessment level EZ only. Table 6, Periodic inspection, has been changed, hig

16、hlighting assessment level EZ only. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International S

17、tandard IEC 60384-13:2011 was approved by CENELEC as a European Standard without any modification. BS EN 60384-13:2012- 3 - EN 60384-13:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are i

18、ndispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicat

19、ed by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60063 + A1 + A2 1963 1967 1977 Preferred number series for resistors and capacitors - - IEC 60068-1 - Environmental testing - Part 1: General and guidance EN 60068-1 - IEC 60384-1 + corr. November 2008 2008 Fixed capacito

20、rs for use in electronic equipment - Part 1: Generic specification EN 60384-1 2009 IEC 60384-13-1 - Fixed capacitors for use in electronic equipment - Part 13-1: Blank detail specification - Fixed polypropylene film dielectric metal foil d.c. capacitors - Assessment level E and EZ EN 60384-13-1 - IE

21、C 60384-14 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains EN 60384-14 - IEC 60410 1973 Sampling plans and procedures for inspection by attributes - - IEC 61193-2

22、- Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 - ISO 3 - Preferred numbers - Series of preferred numbers - - BS EN 60384-13:2012 2 60384-13 IEC:2011 CONTENTS 1 General 6 1.1 Scope 6 1.2 Object . 6 1.3 Normati

23、ve references 6 1.4 Information to be given in a detail specification . 7 1.5 Terms and definitions 8 1.6 Marking . 8 2 Preferred ratings and characteristics 9 2.1 Preferred characteristics . 9 2.2 Preferred values of ratings 9 3 Quality assessment procedures 10 3.1 Primary stage of manufacture 10 3

24、.2 Structurally similar components . 11 3.3 Certified records of released lots . 11 3.4 Qualification approval 11 3.5 Quality conformance inspection . 17 4 Test and measurement procedures . 19 4.1 Visual examination and check of dimensions . 19 4.2 Electrical tests . 19 4.3 Robustness of termination

25、s . 22 4.4 Resistance to soldering heat . 22 4.5 Solderability 22 4.6 Rapid change of temperature 23 4.7 Vibration 23 4.8 Bump 23 4.9 Shock 24 4.10 Climatic sequence . 24 4.11 Damp heat, steady state 25 4.12 Endurance . 26 4.13 Component solvent resistance . 26 4.14 Solvent resistance of marking 26

26、Table 1 Preferred tolerances 9 Table 2 Preferred values and combinations . 10 Table 3 Sampling plan together with numbers of permissible non-conformance for qualification approval test . 12 Table 4 Test schedule for qualification approval. 13 Table 5 Lot-by-lot inspection 18 Table 6 Periodic inspect

27、ion 18 Table 7 Test points and voltages . 19 Table 8 Insulation resistance requirements 21 Table 9 Correction factors 21 BS EN 60384-13:201260384-13 IEC:2011 3 Table 10 Preferred severities . 24 Table 11 Test conditions 26 BS EN 60384-13:2012 6 60384-13 IEC:2011 FIXED CAPACITORS FOR USE IN ELECTRONI

28、C EQUIPMENT Part 13: Sectional specification Fixed polypropylene film dielectric metal foil d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by t

29、his standard are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1, the appro

30、priate quality assessment procedures, tests and measuring methods, and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of at least equal or higher performance level

31、, because lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inclu

32、ding any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1, Environmental testing Part 1:General and guidance IEC 60384-1:2008, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC

33、 60384-13-1, Fixed capacitors for use in electronic equipment Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E and EZ IEC 60384-14, Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacito

34、rs for electromagnetic interference suppression and connection to the supply mains IEC 60410:1973, Sampling plans and procedures for inspection by attributes IEC 61193-2, Quality assessment systems Part 2: Selection and use of sampling plans for inspection of electronic components and packages ISO 3

35、, Preferred numbers Series of preferred numbers BS EN 60384-13:201260384-13 IEC:2011 7 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of

36、the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular

37、 form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions These shall be an illustration of the capacitor as an aid t

38、o easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be

39、given for the length, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations. When necessary, for example, when a number of items (capacitance values/voltage ranges) are covered by a detail specification, th

40、e dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on

41、printed boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal me

42、ans. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Rating and characteristics The ra

43、tings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following. 1.4.3.1 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and applicatio

44、n purposes. 1.4.3.2 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability and the resistance to solder heat test. 1.4.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the pa

45、ckage. Deviations from 1.6 of this sectional specification shall be specifically stated. BS EN 60384-13:2012 8 60384-13 IEC:2011 1.5 Terms and definitions For the purpose of this document, the terms and definitions given in IEC 60384-1 and the following apply. 1.5.1 stability class tolerance on the

46、temperature coefficient together with the permissible change of capacitance after defined tests NOTE 1 The stability class is stated in the detail specification. NOTE 2 Table 2 shows the preferred stability classes. 1.5.2 rated voltage URmaximum d.c. voltage which may be applied continuously to a ca

47、pacitor at the rated temperature NOTE The sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor should not exceed the rated voltage. The value of the peak a.c. voltage should not exceed the following percentages of the rated voltage at the frequencies stated and should be not gr

48、eater than 280 V: 50 Hz: 20 % 100 Hz: 15 % 1 000 Hz: 3 % 10 000 Hz: 1 % unless otherwise specified in the detail specification. 1.6 Marking See IEC 60384-1, 2.4 with the following details. 1.6.1 General The information given in the marking is normally selected from the following list; the relative i

49、mportance of each item is indicated by its position in the list. nominal capacitance; rated voltage (d.c. voltage may be indicated by the symbol or ); tolerance on nominal capacitance; year and month (or week) of manufacture; manufacturers name or trade mark; temperature coefficient and stability class; climatic category; manufacturers type designation; reference to the detail specification; 1.6.2 Marking of capacitors The capacitor shall b