EN 60512-16-18-2008 en Connectors for electronic equipment - Tests and measurements - Part 16-18 Mechanical tests on contacts and terminations - Test 16r Deflection of contacts sim.pdf

1、BRITISH STANDARDBS EN 60512-16-18: 2008Connectors for electronic equipment Tests and measurements Part 16-18: Mechanical tests on contacts and terminations Test 16r: Deflection of contacts, simulationICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g

2、44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-16-18:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 55922 8National forew

3、ordThis British Standard is the UK implementation of EN 60512-16-18:2008. It is identical to IEC 60512-16-18:2008. The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizati

4、ons represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Am

5、endments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD EN 60512-16-18 NORME EUROPENNE EUROPISCHE NORM July 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central

6、 Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-16-18:2008 E ICS 31.220.10 English version Connectors for electronic equipment - Tests and measurements - Part 16-18: M

7、echanical tests on contacts and terminations - Test 16r: Deflection of contacts, simulation (IEC 60512-16-18:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 16-18: Essais mcaniques des contacts et des sorties - Essai 16r: Dbattement des contacts, simulation (CEI 60512-16-

8、18:2008) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 16-18: Mechanische Prfungen an Kontakten und Anschlssen - Prfung 16r: Simulierte Auslenkung von Kontakten (IEC 60512-16-18:2008) This European Standard was approved by CENELEC on 2008-06-01. CENELEC members are bo

9、und to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

10、Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the sam

11、e status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norw

12、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1875/FDIS, future edition 1 of IEC 60512-16-18, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic

13、equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-16-18 on 2008-06-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by whi

14、ch the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-06-01 Annex ZA has been added by CENELEC. _ Endorsement notice The

15、 text of the International Standard IEC 60512-16-18:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-16-18:2008 2 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 16-18: Mechanical tests on contacts and terminations Test 16r: Deflection of co

16、ntacts, simulation 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this pa

17、rt of IEC 60512 is to detail a standard test method to measure the deflection of a simulated contact in its cavity or housing. Although this test method is intended for cylindrical male contacts, and is particularly applicable to those where the contacts fit into an insert, which may have some elast

18、icity, its use for contacts with other geometries and housing details, is not excluded. In which case, the detail specification should contain sufficient detail, given under Clause 5, to enable the test to be done. 2 Normative references The following referenced documents are indispensable for the a

19、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a

20、: Visual examination 3 Preparations 3.1 Preparation of specimen The specimen shall consist of a housing, with an insert or other contact-receiving connector body or device. Any preconditioning given in the component detail specification shall be applied. Five such specimens shall be prepared. 3.2 Eq

21、uipment A test pin (gauge pin) shall be provided, the design of which shall replicate those parts of the contact normally fitted into the cavity that have relevance to this test. A universal testing machine suitable for the test procedure detailed in Clause 4 shall be required, equipped with all rel

22、evant test fixtures needed to hold the specimen under test. 3.3 Mounting If mounting of the specimen is appropriate, it shall be as specified in the component detail specification. The specimen shall not be mated to its corresponding, or other, component. BS EN 60512-16-18:2008 3 Figure 1 and Table

23、1 give an example of a test set up. 1 3 Pa (2) Pa (1) 2 A B 180 4 IEC 747/08 Figure 1 Application of force (example) Table 1 Relevant dimensions for Figure 1 (example) 1 Pivot point of lever arm 2 Effective length of lever arm Pa(1) Point of application of force, phase 1 Pa(2) Point of application o

24、f force, phase 2 3 Fixed or free connector housing or similar device 4 Total deflection A Deflection, phase 1 B Deflection, phase 2 4 Test method 4.1 Procedure At least 10 cavities shall be selected at random from the 5 specimens provided that at least one cavity shall be near the periphery, and one

25、, at or near, the centre of the connector insert or housing. For inserts or housings having 3 or less cavities, all shall be tested. A specified force shall be applied in a manner as, or similar to, that shown in Figure 1 (which is an example). The force shall be applied at a rate not exceeding 10 N

26、/s and shall be maintained for 10 s. The foregoing shall be repeated in the opposite direction. An example is shown in Figure 1. In some cases where the geometry of the connector or insert is not symmetrical, the direction or plane of application of the forces will influence the results. In all case

27、s, the plane of application shall be that which causes the greatest deflection. BS EN 60512-16-18:2008 4 4.2 Measurements and requirements 4.2.1 Before testing Visual examination according to IEC 60512-1-1 shall be carried out. There shall be no defects, which would impair the validity of the test.

28、4.2.2 During testing Deflection on each direction shall be recorded. The sum of these deflections shall be regarded as the total deflection. It shall not exceed that given in the component detail specification. Observation of the test pin shall be made during the test. The test pin shall not distort

29、, either temporarily or permanently, during the test to a degree that would invalidate the test. 4.2.3 After testing Visual examination according to IEC 60512-1-1 shall be carried out. There shall be no defects to the insert or housing, other than those found under 4.2.1 that would impair the normal

30、 functioning of the component, nor shall the test pin be distorted. 5 Details to be specified When this test is required by a detail specification, the following shall be given therein: a) whether preconditioning is required; b) whether special mounting of the specimen is required; c) test pin dimen

31、sions; NOTE 1 Critical dimensions should include lever arm length, pivot point and diameters of the pin. d) force to be applied; e) point of application of force; f) total deflection (see Figure 1); NOTE 2 This may be different for fixed or free, male or female (housing or contacts). g) any deviatio

32、n from the standard test method. _ BS EN 60512-16-18:2008 5 Annex ZA(normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the

33、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 605

34、12-1-1 -1)Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)1)Undated reference. 2)Valid edition at date of issue. BS EN 60512-16-18:2008 6 blankBS EN 60512-16-18: 2008BSI Group Headquarters389 Chiswick High

35、Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBr

36、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity w

37、hile using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscrib

38、ers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from

39、the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europe

40、an and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email:

41、 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding

42、online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardizatio

43、n bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the

44、 free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: