EN 60512-16-6-2008 en Connectors for electronic equipment - Tests and measurements - Part 16-6 Mechanical tests on contacts and terminations - Test 16f Robustness of terminations《电.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI British StandardsWB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 1Connectors forelectronic equipment Tests and measurements Part 16-6: Mechanical tests on contacts and termination

2、s Test 16f: Robustness ofterminationsBS EN 60512-16-6:2008NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LANational forewordThis British Standard is the UK implementation of EN 60512-16-6:2008. Itis identical to IEC 60512-16-6:2008.The UK participation in its preparation was entr

3、usted to TechnicalCommittee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract.

4、 Users are responsible for its correct application. BSI 2009ISBN 978 0 580 55912 9ICS 31.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on Amendments issued si

5、nce publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-16-6:200831 January 2009EUROPEAN STANDARD EN 60512-16-6 NORME EUROPENNE EUROPISCHE NORM September 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Kom

6、itee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-16-6:2008 E ICS 31.220.10 English version Connectors for electronic equipment

7、- Tests and measurements - Part 16-6: Mechanical tests on contacts and terminations - Test 16f: Robustness of terminations (IEC 60512-16-6:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 16-6: Essais mcaniques des contacts et des sorties - Essai 16f: Robustesse des sortie

8、s (CEI 60512-16-6:2008) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 16-6: Mechanische Prfungen an Kontakten und Anschlssen - Prfung 16f: Mechanische Widerstandsfhigkeit von Anschlssen (IEC 60512-16-6:2008) This European Standard was approved by CENELEC on 2008-08-01

9、. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtaine

10、d on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central

11、 Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malt

12、a, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60512-16-6:2008EN 60512-16-6:2008 - 2 - Foreword The text of document 48B/1887/FDIS, future edition 1 of IEC 60512-16-6, prepared by SC 48B, Connectors, of IEC TC 48, E

13、lectromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-16-6 on 2008-08-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the

14、 EN 60512 series. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-05-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 201

15、1-08-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-16-6:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-16-6:2008- 3 - EN 60512-16-6:2008 Annex ZA (normative) Normative references to internatio

16、nal publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm

17、ents) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60068-2-21 2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting d

18、evices EN 60068-2-21 2006 IEC 60512-1-1 - 1)Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 2002 2)1)Undated reference. 2)Valid edition at date of issue. BS EN 60512-16-6:2008 4 60512-16-6 IEC:2008 CONNECTORS FOR

19、 ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 16-6: Mechanical tests on contacts and terminations Test 16f: Robustness of terminations 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electrical connectors within the scope of IEC technical

20、 committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the ability of terminations to withstand the mechanical stresses likely to be applied during normal assembly oper

21、ations. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Con

22、nectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination IEC 60068-2-21:2006, Environmental testing Part 2-21: Tests Test U: Robustness of terminations and integral mounting devices 3 Preparations 3.1 Preparation of specimen The specimen shall

23、 consist of a component with its terminations, and may be wired if so specified in the component detail specification. Any preconditioning given in the component detail specification shall be applied. 3.2 Mounting If mounting of the specimen is appropriate, it shall be as specified in the component

24、detail specification. 4 Test method 4.1 Procedure The test shall be carried out in accordance with the part or parts of test U of IEC 60068-2-21, as specified in the applicable detail specification. BS EN 60512-16-6:200860512-16-6 IEC:2008 5 4.2 Measurements and requirements 4.2.1 Before testing Vis

25、ual examination according to IEC 60512-1-1 shall be carried out. There shall be no defects, which would impair the validity of the test. 4.2.2 After testing Visual examination according to IEC 60512-1-1 shall be carried out. There shall be no defects, other than any found under 3.2.1, that would imp

26、air the normal functioning of the component. 5 Details to be specified When this test is required by a detail specification, the following details shall be specified: a) any preconditioning required; b) if the specimen is to be wired, if so details of this; c) if special mounting of the specimen is

27、required; d) number of specimens to be tested; e) any deviation from the standard test method. _ BS EN 60512-16-6:2008This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standar

28、ds in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users

29、 of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products andservices. We would be grateful if anyone finding an inaccuracy orambiguity while using this British Standard would inform the Secretary oft

30、he technical committee responsible, the identity of which can be foundon the inside front cover.Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS whichensures that subscribers automatically receive the latest editions ofstandards.Buying st

31、andardsOrders for all BSI, international and foreign standards publicationsshould be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: You may also buy directly using a debit/credit card from the BSI Shopon the website response to orders for international st

32、andards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library.Various BSI electronic inf

33、ormation services are also available which givedetails on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standardsdevelopments and receive substantial discounts on the purchas

34、e priceof standards. For details of these and other benefits contact MembershipAdministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI

35、 website CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of thepublications of the international standardization bodies. Except as permitted under theCopyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrievalsystem or tra

36、nsmitted in any form or by any means electronic, photocopying, recording orotherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard of necessarydetails such as symbols, and size, type or grade designations. If these details are to be used forany other purpose than implementation then the prior written permission of BSI must beobtained. Details and advice can be obtained from the Copyright & Licensing Manager.Tel: +44 (0)20 8996 7070 Email: WB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 2