EN 60512-17-4-2010 en Connectors for electronic equipment - Tests and measurements - Part 17-4 Cable clamping tests - Test 17d Cable clamp resistance to cable torsion《电子设备连接器 试验和测量.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 17-4: Cable clamping tests Test 17d: Cable clamp resistance to cable torsionBS EN 60512-17-4:2010National forewordT

2、his British Standard is the UK implementation of EN 60512-17-4:2010. It isidentical to IEC 60512-17-4:2010. This standardsupersedes Test 17d from The UK participation in its preparation was entrusted to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic

3、equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 62164 2ICS 31.220.01Compliance

4、with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 November 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-17-4:2010BS 5772-9:

5、1993, IEC 60512-9:1992, which will remain current until all the tests it contains have been revised.EUROPEAN STANDARD EN 60512-17-4 NORME EUROPENNE EUROPISCHE NORM September 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisch

6、es Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-17-4:2010 E ICS 31.220.01 English version Connectors for electronic equipmen

7、t - Tests and measurements - Part 17-4: Cable clamping tests - Test 17d: Cable clamp resistance to cable torsion (IEC 60512-17-4:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 17-4: Essais de maintien des cbles - Essais 17d: Rsistance de la pince de maintien du cble la t

8、orsion des cbles (CEI 60512-17-4:2010) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 17-4: Prfungen der Kabelabfangung - Prfung 17d: Widerstandsfhigkeit der Kabelabfangung gegen Kabeltorsion (IEC 60512-17-4:2010) This European Standard was approved by CENELEC on 2010-

9、09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be ob

10、tained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Ce

11、ntral Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

12、xembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60512-17-4:2010EN 60512-17-4:2010 - 2 - Foreword The text of document 48B/2157/FDIS, future edition 1 of IEC 60512-17-4, prepared by SC 48B, Connectors, o

13、f IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-17-4 on 2010-09-01. Attention is drawn to the possibility that some of the elements of this document may be the subject

14、 of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-06-01 late

15、st date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-09-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-17-4:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 6

16、0512-17-4:2010- 3 - EN 60512-17-4:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applie

17、s. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 - Connectors

18、for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 - BS EN 60512-17-4:2010 4 60512-17-4 IEC:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 17-4: Cable clamping tests Test 17d: Cable clamp resistance to ca

19、ble torsion 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a st

20、andard test method to assess the ability of a cable-clamping device to prevent the rotation of the cable/wire bundle around its axis. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies

21、. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 3 Preparation of the specimen The specimen shall consist of

22、the specified cable/wire bundle fitted in the normal manner to its associated component or sub-assembly by means of the cable-clamping device. The specimen shall be prepared and mounted in accordance with the detail specification. 4 Test method This test shall be done by means of a suitable device t

23、o measure and control the torque, e.g. a universal torque tester. With the specimen rigidly mounted, a torque shall be applied to the cable/wire bundle at a specified distance from the cable-clamping device. This torque shall be increased gradually at a rate not exceeding 0,5 Nm/s until the specifie

24、d value is reached. The maximum value shall be maintained for 1 min, unless otherwise specified in the detail specification. 5 Final measurements The specimen shall be examined visually according to IEC 60512-1-1, test 1a at the junction of the cable/wire bundle and the clamping device and at the ju

25、nction of the clamping device and the component or sub-assembly. BS EN 60512-17-4:201060512-17-4 IEC:2010 5 6 Requirements The cable/wire bundle shall not have moved within the clamping device. The clamp shall not have moved in relation to the component or sub-assembly body beyond the limits specifi

26、ed in the detail specification. 7 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) preparation of the specimen and type of cable/wire bundle to be used; b) mounting of the specimen; c) details of the test; d) value of the to

27、rque, direction and point of application; e) requirements for final measurements; f) any deviation from the standard test method. _ BS EN 60512-17-4:2010This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsa

28、nd other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4

29、AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if

30、 anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating servi

31、ce called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all o

32、rders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas Bri

33、tish Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also avail

34、able whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact

35、 Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also ho

36、lds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recordi

37、ng or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: