EN 60512-8-3-2011 en Connectors for electronic equipment - Tests and measurements - Part 8-3 Static load tests (fixed connectors) - Test 8c Robustness of actuating lever《电子设备连接器 试验.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 8-3: Static load tests (fixed connectors) Test 8c: Robustness of actuating leverBS EN 60512-8-3:2011National forewo

2、rdThis British Standard is the UK implementation of EN 60512-8-3:2011. It is identical to IEC 60512-8-3:2011. It supersedes Test 8c from BS 5772-5:1993, IEC 60512-5:1992, which will remain current until all the tests it contains have been revised.The UK participation in its preparation was entrusted

3、 to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U

4、sers are responsible for its correct application. BSI 2011ISBN 978 0 580 62116 1 ICS 31.220.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2011.Amendm

5、ents issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-8-3:2011EUROPEAN STANDARD EN 60512-8-3 NORME EUROPENNE EUROPISCHE NORM June 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr

6、Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-8-3:2011 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and m

7、easurements - Part 8-3: Static load tests (fixed connectors) - Test 8c: Robustness of actuating lever (IEC 60512-8-3:2011) Connecteurs pour quipements lectroniques Essais et mesures Partie 8-3: Essais de charge statique (embases) Essai 8c: Robustesse de lergot dactivation (CEI 60512-8-3:2011) Steckv

8、erbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 8-3: Prfungen mit statischer Last (feste Steckverbinder) - Prfung 8c: Mechanische Widerstandsfhigkeit des Bettigungshebels (IEC 60512-8-3:2011) This European Standard was approved by CENELEC on 2011-05-12. CENELEC members are bo

9、und to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

10、Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the sam

11、e status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherla

12、nds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60512-8-3:2011EN 60512-8-3:2011 Foreword The text of document 48B/2121/CDV, future edition 1 of IEC 60512-8-3, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical componen

13、ts and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-8-3 on 2011-05-12. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100, which explains the structure of the EN 60512 series. Attenti

14、on is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national le

15、vel by publication of an identical national standard or by endorsement (dop) 2012-02-12 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-05-12 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-

16、8-3:2011 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60512-14 series NOTE Harmonized in EN 60512-14 series (not modified) IEC 60529 NOTE Harmonized as EN 6052

17、9. _ BS EN 60512-8-3:2011EN 60512-8-3:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

18、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1 - Connector

19、s for electronic equipment - Tests and measurements - Part 1: General EN 60512-1 - IEC 60512-1-1 - Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 - IEC 60512-1-100 - Connectors for electronic equipment - Tests a

20、nd measurements - Part 1-100: General - Applicable publications EN 60512-1-100 - BS EN 60512-8-3:201160512-8-3 IEC:2011 CONTENTS 1 Scope and object . 5 2 Normative references . 5 3 Preparation . . 5 Preparation of the specimen 5 3.1Equipment . . 5 3.2Mounting . . 5 3.34 Test method . 6 Force . . 6 4

21、.1Torque 7 4.25 Final measurements . 7 6 Requirements . 7 7 Details to be specified . . 7 Bibliography . 8 Figure 1 Details of force application . 6 BS EN 60512-8-3:201160512-8-3 IEC:2011 5 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 8-3: Static load tests (fixed connectors) Test

22、 8c: Robustness of actuating lever 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this

23、 standard is to detail a standard test method to assess the robustness of the actuating lever of a connector mating or release mechanism. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited app

24、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1, Connectors for electronic equipment Tests and measurements Part 1: General IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examinat

25、ion Test 1a: Visual examination IEC 60512-1-100, Connectors for electronic equipment Tests and measurements Part 1-100: General Applicable publications 3 Preparation Preparation of the specimen 3.1The specimen shall not be wired but shall be fitted with such accessories as may be required by the det

26、ail specification. Unless otherwise specified, the specimen shall be mounted in the normal manner, using the normal panel or chassis cut-out as laid down in the detail specification. NOTE The plate should be strong enough to sustain the applied forces. The length and width of the plate should be suc

27、h that the contour of the specimen is exceeded. Equipment 3.2A suitable test tool (e.g. a universal materials testing machine) and appropriate adapters shall be used. Mounting 3.3Unless otherwise specified, the specimen shall be mounted in the normal manner, using the normal panel or chassis cut-out

28、 as laid down in the detail specification. BS EN 60512-8-3:2011 6 60512-8-3 IEC:2011 NOTE The plate should be strong enough to sustain the applied forces. The length and width of the plate should be such that the contour of the specimen is exceeded. 4 Test method Force 4.1A specified force shall be

29、applied at the tip of the actuating lever. This force shall be applied in each of the following directions (see Figure 1): perpendicular to the lever axis and in the plane of lever travel and at each end position of the lever (Fa1and Fa2); perpendicular to the lever axis and perpendicular to the pla

30、ne of lever travel at each position of the lever (Fb1and Fb2); axially with the lever axis towards the lever pivot (Fc); axially with the lever axis away from the lever pivot (Fd). The force shall be steadily increased at a rate of approximately 20 N/s up to the specified value and maintained for 1

31、min. Fd Fc Fa1Fb1Fa2Fb2IEC 690/11 Figure 1 Details of force application BS EN 60512-8-3:201160512-8-3 IEC:2011 7 Torque 4.2A specified torque shall be applied around the axis of the lever in either direction for 1 min. 5 Final measurements a) Visual examination (IEC 60512-1-1, Test 1a). b) Applicabl

32、e operational characteristics. NOTE if applicable, the detail specification may require a sealing test from the IEC 60512-14 series or an ingress protection test according IEC 60529. 6 Requirements There shall be no damage which would impair normal operation. 7 Details to be specified When this test

33、 is required by the detail specification, the following details shall be specified: a) mounting details, including dimensions of the panel cut-out; b) shape of the fixture or tool used for applying the force/torque; c) force/torque to be applied, direction and rate of application; d) requirements fo

34、r final measurements; e) any deviation from the standard test method. BS EN 60512-8-3:2011 8 60512-8-3 IEC:2011 Bibliography IEC 60512-14 (all parts), Connectors for electronic equipment Tests and measurements Part 14: Sealing tests IEC 60529, Degrees of protection provided by enclosures (IP Code) _

35、 BS EN 60512-8-3:2011This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated

36、by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the la

37、test amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which

38、 can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying st

39、andardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In r

40、esponse to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through

41、its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with sta

42、ndardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards

43、Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988

44、no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: