EN 60512-9-1-2010 en Connectors for electronic equipment - Tests and measurements - Part 9-1 Endurance tests - Test 9a Mechanical operation《电子设备用连接器 试验和测量 第9-1部分 耐久性试验 试验9a 机械操作》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 9-1: Endurance tests Test 9a: Mechanical operationBS EN 60512-9-1:2010National forewordThis British Standard is the

2、 UK implementation of EN 60512-9-1:2010. It isidentical to IEC 60512-9-1:2010. It supersedes Test 9a from BS 5772-5:1993,IEC 60512-5:1992, which remains current until all the tests it contains havebeen revised.The UK participation in its preparation was entrusted to Technical CommitteeEPL/48, Electr

3、omechanical components and mechanical structures for elec-tronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct ap

4、plication. BSI 2010ISBN 978 0 580 62121 5ICS 31.220.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 May 2010.Amendments issued since publicationAmd. No. Date

5、Text affectedBRITISH STANDARDBS EN 60512-9-1:2010EUROPEAN STANDARD EN 60512-9-1 NORME EUROPENNE EUROPISCHE NORM April 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centr

6、e: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-9-1:2010 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests -

7、Test 9a: Mechanical operation (IEC 60512-9-1:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 9-1: Essais dendurance - Essai 9a: Fonctionnement mcanique (CEI 60512-9-1:2010) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 9-1: Dauerprfungen -

8、Prfung 9a: Mechanische Lebensdauer (IEC 60512-9-1:2010) This European Standard was approved by CENELEC on 2010-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard witho

9、ut any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other languag

10、e made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republ

11、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60512-9-1:2010EN 60512-9-1:2010 - 2 - Forew

12、ord The text of document 48B/2018/CDV, future edition 1 of IEC 60512-9-1, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-9-1 on 2010-

13、04-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented

14、at national level by publication of an identical national standard or by endorsement (dop) 2011-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Stand

15、ard IEC 60512-9-1:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-9-1:2010- 3 - EN 60512-9-1:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are

16、indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indica

17、ted by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 - Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 - IEC 60512-2-1 - Connectors for electronic equipment - Tests and measur

18、ements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method EN 60512-2-1 - IEC 60512-2-6 - Connectors for electronic equipment - Tests and measurements - Part 2-6: Electrical continuity and contact resistance tests - Test 2f: Housing (

19、shell) electrical continuity EN 60512-2-6 - IEC 60512-3-1 - Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance EN 60512-3-1 - IEC 60512-4-1 - Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stres

20、s tests - Test 4a: Voltage proof EN 60512-4-1 - IEC 60512-13-5 - Connectors for electronic equipment - Tests and measurements - Part 13-5: Mechanical operating tests - Test 13e: Polarizing and keying method EN 60512-13-5 - BS EN 60512-9-1:2010 4 60512-9-1 IEC:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT

21、 TESTS AND MEASUREMENTS Part 9-1: Endurance tests Test 9a: Mechanical operation 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a

22、 detail specification. The object of this standard is to detail a standard test method to assess the mechanical operational endurance of connectors in the normal operating mode, without electrical load. 2 Normative references The following referenced documents are indispensable for the application o

23、f this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1: Connectors for electronic equipment Tests and measurements Part 1-1: General examination, Test 1a: Visual ex

24、amination IEC 60512-2-1: Connectors for electronic equipment Tests and measurements Part 2-1: Electrical continuity and contact resistance tests Test 2a: Contact resistance Millivolt level method IEC 60512-2-6: Connectors for electronic equipment Tests and measurements Part 2-6: Electrical continuit

25、y and contact resistance tests Test 2f: Housing (shell) electrical continuity IEC 60512-3-1: Connectors for electronic equipment Tests and measurements Part 3-1: Insulation tests Test 3a: Insulation resistance IEC 60512-4-1: Connectors for electronic equipment Tests and measurements Part 4-1: Voltag

26、e stress tests Test 4a: Voltage proof IEC 60512-13-5: Connectors for electronic equipment Tests and measurements Part 13-5: Mechanical operation tests Test 13e: Polarizing and keying method 3 Preparation of the specimen The specimen shall be prepared and mounted according to the detail specification

27、. 4 Test method The specimen shall be subjected to a mechanical operational endurance test in accordance with the requirements of the detail specification (without electrical load). The specimen shall be operated in the normal manner. BS EN 60512-9-1:201060512-9-1 IEC:2010 5 Frequency, number and sp

28、eed of the operations shall be as stated in the detail specification. Unless prohibited by the detail specification, mechanical aids which simulate normal operation may be used provided that they do not introduce abnormal stresses. 5 Final measurements a) Visual examination (IEC 60512-1-1, test 1a).

29、 b) Contact resistance (IEC 60512-2-1, test 2a, as appropriate). c) Housing (shell) electrical continuity IEC 60512-2-6, (test 2f). d) Insulation resistance (IEC 60512-3-1, test 3a). e) Voltage proof (IEC 60512-4-1, test 4a). f) Mechanical operational characteristics, including effectiveness of keys

30、 and polarizing method (IEC 60512-13-5, test 13e). NOTE If applicable, the detail specification may require a sealing test from the IEC 60512-14 series or an ingress protection test according IEC 60529. 6 Details to be specified When this test is required by the detail specification, the following d

31、etails shall be specified: a) preparation of the specimen, including type of cable/wire bundle to be used; b) mounting of the specimen; c) number, frequency and speed of operations; d) requirements for final measurements; e) any deviation from the standard test method. _ BS EN 60512-9-1:2010This pag

32、e deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorpora

33、ted by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess th

34、e latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of w

35、hich can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buyin

36、g standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email:

37、In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards thro

38、ugh its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with

39、 standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStanda

40、rds Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1

41、988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: