EN 60512-99-001-2012 en Connectors for electronic equipment - Tests and measurements - Part 99-001 Test schedule for engaging and separating connectors under electrical load - Test.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 99-001: Test schedule for engagingand separating connectors under electrical load Test 99a: Connectors used in twis

2、ted pair communication cabling with remote powerBS EN 60512-99-001:2012National forewordThis British Standard is the UK implementation of EN 60512-99-001:2012. It is identical to IEC 60512-99-001:2012.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechani

3、cal components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicati

4、on. The British Standards Institution 2012.Published by BSI Standards Limited 2012.ISBN 978 0 580 66656 8 ICS 31.220.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committ

5、ee on 30 November 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-99-001:2012EUROPEAN STANDARD EN 60512-99-001 NORME EUROPENNE EUROPISCHE NORM October 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation El

6、ectrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-99-001:2012 E ICS 31.220.10 English version Connecto

7、rs for electronic equipment - Tests and measurements - Part 99-001: Test schedule for engaging and separating connectors under electrical load - Test 99a: Connectors used in twisted pair communication cabling with remote power (IEC 60512-99-001:2012) Connecteurs pour quipements lectroniques - Essais

8、 et mesures - Partie 99-001: Programme dessai relatif aux connexions et dconnexions sous charge lectrique - Essai 99a: Connecteurs utiliss dans le cblage de communication paires torsades permettant une alimentation distance (CEI 60512-99-001:2012) Steckverbinder fr elektronische Einrichtungen - Mess

9、 und Prfverfahren - Teil 99-001: Prfablaufplan fr Steckverbinder zum Stecken und Ziehen mit elektrischer Belastung - Prfung 99a: Steckverbinder fr die Anwendung in paarverseilter Kommunikationsverkabelung mit Fernspeisung (IEC 60512-99-001:2012) This European Standard was approved by CENELEC on 201

10、2-09-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be

11、obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notifi

12、ed to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Gr

13、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60512-99-001:2012EN 60512-99-001:2012 Foreword The text of document 48B/2291/FDIS, fu

14、ture edition 1 of IEC 60512-99-001, prepared by 48B “Connectors“ of IEC/TC 48 “Electromechanical components and mechanical structures for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60512-99-001:2012. The following dates are fixed: latest date b

15、y which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-06-17 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-09-17 Attention is drawn to the possibility that

16、some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60512-99-001:2012 was approved by CENELEC as a European Standard wi

17、thout any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60512-1-1 NOTE Harmonised as EN 60512-1-1. IEC 60512-2-1 NOTE Harmonised as EN 60512-2-1. IEC 60512-3-1 NOTE Harmonised as EN 60512-3-1. IEC 60512-4-1 NOTE Harmoni

18、sed as EN 60512-4-1. IEC 60512-11-7 NOTE Harmonised as EN 60512-11-7. BS EN 60512-99-001:2012EN 60512-99-001:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively refer

19、enced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modific

20、ations, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512 Series Connectors for electronic equipment - Tests and measurements EN 60512 Series IEC 60512-1-100 - Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable pu

21、blicationsEN 60512-1-100 - IEC 60512-9-3 2011 Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (engaging and separating) with electrical load EN 60512-9-3 2011 IEC 61156 Series Multicore and symmetrical pair/quad cables for digi

22、tal communications - - BS EN 60512-99-001:201260512-99-001 IEC:2012 CONTENTS 1 Scope and object . 5 2 Normative references . 5 3 General . 5 4 Preparation of specimen . 6 5 Test circuit requirements 6 5.1 General . 6 5.2 Voltage and current . 6 5.3 Auxiliary equipment . 7 6 Tests and test schedule 7

23、 6.1 Test group UEL 1 7 Annex A (informative) Test voltage and current setting instructions . 10 Bibliography . 11 Figure 1 Test circuit details 6 Table 1 Test group UEL 1 7 BS EN 60512-99-001:201260512-99-001 IEC:2012 5 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 99-001: Test sc

24、hedule for engaging and separating connectors under electrical load Test 99a: Connectors used in twisted pair communication cabling with remote power 1 Scope and object This part of IEC 60512 is used for the assessment of connectors within the scope of SC 48B that are used in twisted pair communicat

25、ion cabling with remote power, such as ISO/IEC 11801 Class D, or better, balanced cabling in support of IEEE Std 802.3at-2009 (PoE Plus Power over Ethernet Plus). The object of this standard is to detail a test schedule to determine the ability of connectors to withstand a minimal number of engageme

26、nts and separations when an electrical current is being passed through the connector in accordance with IEC 60512-9-3. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, onl

27、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512 (all parts): Connectors for electronic equipment Tests and measurements IEC 60512-1-100: Connectors for electronic equipment Tests and measurements Part 1-

28、100: General Applicable publications IEC 60512-9-3:2011, Connectors for electronic equipment Tests and measurements Part 9-3: Endurance tests Test 9c: Mechanical operation (engaging and separating) with electrical load IEC 61156 (all parts): Multicore and symmetrical pair/quad cables for digital com

29、munications 3 General The current carrying capacity of a mated connector, including the corresponding current de-rating for temperature, shall be specified in the detail specification. Although many applications are configured such that the current is not drawn until after full engagement of the con

30、nector has been achieved (i.e. the connector does not “make” the current), this test schedule is suitable for verification of engaging and separating of connectors under PoE Plus load conditions where this may occur in practice. An application specific current, and associated open circuit voltage, i

31、s specified that corresponds with the current and voltage of the supported application. The circuitry and test conditions given in this standard correspond to the conditions associated with ISO/IEC 11801 Class D, or better, balanced cabling in support of IEEE 802.3at (PoE Plus Power over Ethernet Pl

32、us) BS EN 60512-99-001:2012 6 60512-99-001 IEC:2012 Further information on the possible effects of such operations may be found in IEC TR 62652. NOTE The above documents are not essential for the application of this standard but are given as source of information, as such, they may be found in the B

33、ibliography. 4 Preparation of specimen Each specimen shall consist of a mated connector with its terminations. Specimens shall be conformant to the relevant IEC connector standards. Each free connector and each fixed connector shall be terminated with 3 m (max.) of the maximum conductor size cable f

34、or which it is intended to be terminated, according to IEC 61156 series. For each specimen, all of the circuits (mated contacts) shall be wired in parallel, as given in IEC 60512-9-3, and all of the circuits shall be tested (see Figure 1). If necessary, a printed circuit board may be used which shal

35、l not influence the test results. 5 Test circuit requirements 5.1 General The values for the circuit components and the details of the test circuit, referenced in IEC 60512-9-3, shall be as shown in Figure 1. 6 1 2 3 4 5 IEC 1098/12 Key 1 Cables in accordance with 4.1 2 Connector under test 3 Induct

36、or 100 H 4 Variable resistor (e.g. 50 to 300 ) 5 Capacitor 5 F 6 Power source NOTE 1 Only one circuit of the connector under test, as referenced in IEC 60512-9-3, is shown for clarity. Items 1, 3, 4, 5, and 6, are replicated for each circuit (engaged contacts) of the connector. Item 6 may be single

37、or multiple. Each circuit of the specimen shall be wired in parallel with the other circuits of the specimen, and all circuits of each specimen shall operate simultaneously. NOTE 2 The variable resistor(s) are used to adjust the current(s) to the specified value. Figure 1 Test circuit details 5.2 Vo

38、ltage and current The variable resistor(s) shall be set so that the electrical current in each circuit (mated contacts) of the specimen is 0,6 A. When specimen is unmated, the open circuit voltage, in all circuits, shall be 55 V d.c. See Annex A. IEEE 802.3 at specifies a maximum current of 0,3 A pe

39、r conductor and an open circuit voltage of 55 V d.c. The test current has been doubled to 0,6 A in order to represent the high BS EN 60512-99-001:201260512-99-001 IEC:2012 7 probability that one contact of any given pair will separate before the other. Therefore as in the cited application, where cu

40、rrent is carried by pairs of contacts in multiple parallel circuits, the last contact to break will do so carrying all the current (twice the nominal). 5.3 Auxiliary equipment The test laboratory may choose to use switches to reverse polarity. However, use of such switches shall not influence the te

41、st parameters. 6 Tests and test schedule 6.1 Test group UEL 1 A minimum number of 8 specimens shall be prepared for this group; then tested according to Table 1. Table 1 Test group UEL 1 Test Phase Test Measurement to be performed Title IEC 60512 test No. Severity or condition of test Title IEC 6051

42、2 test No. Requirements UEL 1.1 General examination 1 Visual examination 1a There shall be no defects that would impair normal operation UEL 1.2 Contact resistance Millivolt level method 2a Contact resistance 20 m maximum UEL 1.3 100 V d.c. Method A Mated connectors Insulation resistance 3a 500 M mi

43、nimum UEL 1.4 Contact to contact All signal contacts to shield and test panel, as applicable Method A Mated connectors Voltage proof 4a 1 000 V d.c. or a.c. peak 1 500 V d.c. or a.c. peak UEL 1.5 An electrical load, current and open circuit voltage, as detailed in Clause 5, shall be applied to each

44、specimen. For the purpose of this test one connector shall be fixed and the other disengaged at a speed of 150 10 mm/s. One engagement and one separation constitute one cycle. 25 cycles shall be performed. The polarity of the d.c. source (direction of the electrical current) shall be reversed and 25

45、 further cycles performed. Mechanical operations with electrical load 9c BS EN 60512-99-001:2012 8 60512-99-001 IEC:2012 Table 1 (continued) Test Phase Test Measurement to be performed Title IEC 60512 test No. Severity or condition of test Title IEC 60512 test No. Requirements UEL 1.6 Flowing mixed

46、gas test. Method 1 11g 4 days. Half of the samples mated; half of the samples unmated 11g UEL 1.7 Contact resistance-Millivolt level method 2a 20 m maximum change from initial UEL 1.8 An electrical load, current and open circuit voltage, as detailed in Clause 5, shall be applied to each specimen. Fo

47、r the purpose of this test one connector shall be fixed and the other disengaged at a speed of 150 10 mm/s. One engagement and one separation constitute one cycle. 25 cycles shall be performed. The polarity of the dc. source (direction of the electrical current) shall be reversed and 25 further cycl

48、es performed. The specified testing is done with voltage present during engagement. If a specimen does not “pass” the test sequence, the test shall be repeated with a new specimen, without applied voltage during engagement, but the appropriate voltage and current shall be applied during disengagemen

49、t. A connector passing the test in this manner shall be reported as such in test reports. Further, this information shall be made evident in the all relevant documentation of the manufacturer and supplier regarding this mode of complying with this test schedule requirement. Mechanical Operations with electrical load. 9c BS EN 60512-99-001:201260512-99-001 IEC:2012 9 Table 1 (continued) Test Phase Test Measurement to be performed Title IEC 60512 test No. Sever