EN 60684-3-211-2007 en Flexible insulating sleeving - Part 3 Specifications for individual types of sleeving - Sheet 211 Heat-shrinkable sleeving semi-rigid polyolefin shrink ratio.pdf

1、BRITISH STANDARDBS EN 60684-3-211: 2007Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1The European Standard EN 60684-3-211:2007 has the status of a British StandardICS 29.035.20g49g50g3g

2、38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60684-3-211:2007This British Standard was published under the authority of the Standards Policy and Str

3、ategy Committee on 29 June 2007 BSI 2007ISBN 978 0 580 52964 1National forewordThis British Standard was published by BSI. It is the UK implementation of EN 60684-3-211:2007. It is identical with IEC 60684-3-211:2007. It supersedes BS EN 60684-3-211:2002 which is withdrawn.The UK participation in it

4、s preparation was entrusted by Technical Committee GEL/15, Solid electrical insulating materials, to Subcommittee GEL/15/3, Material specifications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the n

5、ecessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-211 NORME EUROPENNE EUROPISCHE NORM May 2007 CEN

6、ELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved wor

7、ldwide for CENELEC members. Ref. No. EN 60684-3-211:2007 E ICS 29.035.20 Supersedes EN 60684-3-211:2002English version Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1 (IEC 60684-3-21

8、1:2007) Gaines isolantes souples - Partie 3: Spcifications pour types particuliers de gaines - Feuille 211: Gaines thermortractables, en polyolfine, semi-rigides, rapport de rtreint 2:1 (CEI 60684-3-211:2007) Isolierschluche - Teil 3: Anforderungen fr einzelne Schlauchtypen - Blatt 211: Wrmeschrumpf

9、schluche, halbfestes Polyolefin, Schrumpfverhltnis 2:1 (IEC 60684-3-211:2007) This European Standard was approved by CENELEC on 2007-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a n

10、ational standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A versio

11、n in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the

12、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 15/357

13、/FDIS, future edition 3 of IEC 60684-3-211, prepared by IEC TC 15, Solid electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-211 on 2007-04-01. This European Standard supersedes EN 60684-3-211:2002. The major technical changes wit

14、h regard to EN 60684-3-211:2002 concern a better alignment with existing national specifications. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-01-01 latest date by whi

15、ch the national standards conflicting with the EN have to be withdrawn (dow) 2010-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60684-3-211:2007 was approved by CENELEC as a European Standard without any modification. _ EN 60684-3-211:2007

16、2 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Designation 7 4 Conditions of test .7 5 Requirements .7 6 Sleeving conformance 7 Table 1 Dimensional requirements .7 Table 2 Property requirements.8 Table 3 Breakdown voltage9 Table 4 Fluid resistant property requirements for

17、 types C and D 9 Table 5 Resistance to selected fluids.10 EN 60684-3-211:2007 3 INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part 1: Definitions and general requirements (IEC 606

18、84-1) Part 2: Methods of test (IEC 60684-2) Part 3: Specifications for individual types of sleeving (IEC 60684-3) This standard comprises one of the sheets of Part 3 as follows: Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1 EN 60684-3-211:2007 4 FLEXIBLE INSULATING SLE

19、EVING Part 3: Specifications for individual types of sleeving Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1 1 Scope This part of IEC 60684 gives the requirements for four types of semi-rigid, heat-shrinkable polyolefin sleeving with a nominal shrink ratio of 2:1 that h

20、as been found suitable for temperatures up to 135 C. Type A: general purpose, flame-retarded, opaque colours; Type B: general purpose, non flame-retarded, translucent; Type C: fluid resistant, flame-retarded, opaque colours; Type D: fluid resistant, non flame-retarded, translucent. The sleeving is n

21、ormally available in internal diameter sizes up to 12,7 mm as supplied, in the following colours: black, white, red, yellow, blue and translucent. Sizes or colours other than those specifically listed in this standard may be available as custom items. The items are considered to comply with this sta

22、ndard if they comply with the property requirements listed in tables 2, 3 and also with the property requirements of Table 4 for types C and D, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user f

23、or a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference

24、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60684-1:2003, Flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of t

25、est1)Amendment 1 (2003) Amendment 2 (2005) IEC 60757:1983, Code for designation of colours ISO 1817:2005, Rubber, vulcanized Determination of the effect of liquids 1)A consolidated edition 2.1 exists, including IEC 60684-2:1997 and its Amendment 1 (2003). EN 60684-3-211:2007 5 3 Designation The slee

26、ving shall be identified by the following designation: Description IEC publication number IEC part number IEC sheet number IEC Type Size (expanded/ recovered internal diameter, in millimetres) Colour - - - - - - Sleeving IEC 60684 3 211 B 12,7/6,4 TT Any abbreviation used for colour shall comply wit

27、h IEC 60757. Where no abbreviation is given, the colour shall be written in full. 4 Conditions of test Unless otherwise specified, the sleeving shall be shrunk in a forced air circulation oven for (5 1) min at 200 C 3 K before being tested. 5 Requirements In addition to the general requirements give

28、n in IEC 60684-1, the sleeving shall comply with the requirements of Tables 1, 2, 3 and 4, where applicable. 6 Sleeving conformance Conformance with the requirements of this specification shall normally be based on the results from size 12,7 mm/6,4 mm black sleeving. The colour fastness to light sha

29、ll be determined for all colours. Table 1 Dimensional requirements Internal diameter mm Size code Expanded min. Recovered max. Recovered wall thickness mm 1,2/0,6 1,2 0,6 0,50 0,10 1,6/0,8 1,6 0,8 0,50 0,10 2,4/1,2 2,4 1,2 0,50 0,10 3,2/1,6 3,2 1,6 0,50 0,10 4,8/2,4 4,8 2,4 0,65 0,15 6,4/3,2 6,4 3,2

30、 0,65 0,15 9,5/4,8 9,5 4,8 0,75 0,15 12,7/6,4 12,7 6,4 0,75 0,15 EN 60684-3-211:2007 6 Table 2 Property requirements Property IEC 60684-2 clause or subclause Units Max.or min. Requirements Remarks Dimensions 3 internal diameter 3.1.2 mm Table 1 wall thickness 3.3.2 mm Table 1 concentricity 3.3.3 % M

31、in. expanded 65 recovered 85 Density 4 g/cm3Max. Type A and C: 1,40 Type B and D: 1,00 Heat shock (Type A and B) 6 No sign of dripping, cracking or flowing The heating temperature shall be 250 C 5 K Heat shock (Type C and D) Tensile strength Elongation 6 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 1

32、2 100 Heat at 200 C 5 K Longitudinal change 9 % Max. +1 10 Heat the expanded sleeving at 200 C 5 K for (5 1) min Bending at low temperature 14 No cracks shall be visible Condition at 55 C 3 K For strips, the mandrel shall be no more than 10 times the wall thickness. Full section sleeving is tested u

33、nfilled and the mandrel shall be no more than 10 times the outer diameter Dimensional stability on storage 16 The dimensions shall be as specified in table 1 Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 14 200 Use a jaw separation rate of 100 mm/min. Below 6,5 mm

34、diameter, as sleeving; at 6,5 mm diameter and above, as dumb-bells. Secant modulus at 2 % elongation 19.4 MPa Min. 175 Breakdown voltage 21 kV Min. See Table 3 Volume resistivity 23 at room temperature 23.4.2 m Min. 1012 after damp heat 23.4.4 m Min. 1011Flame propagation 26 Type A and C only Method

35、 C Time of burning s Max. 30 Length burned mm Max. 75 Copper corrosion 33 % Max. None above the allowable 8 % Heat for (16 0,5) h at 175 C 3 K EN 60684-3-211:2007 7 Table 2 (continued) Property IEC 60684-2 clause or subclause Units Max.or min. Requirements Remarks Colour fastness to light 34 The col

36、our contrast between the exposed and unexposed parts of the specimens shall be equal to or less than that of the fastness standard Fastness standard N. 5 Long-term ageing Elongation at break 50 % Min. 125 Heat at 135 C 3 K Heat ageing Tensile strength Elongation at break 39 19.1 and 19.2 19.1 and 19

37、.2 MPa % Min. Min. 12 100 Heat at 175 C 3 K Water absorption 40 % Max. 0,5 Breakdown voltage shall be determined at room temperature by any of the methods described in 21.2, 21.3 or 21.4 of IEC 60684-2. The rate of application of voltage shall be 500 V/s. Table 3 Breakdown voltage Nominal recovered

38、wall thickness mm Breakdown voltage kV 0,50 10,0 0,65 12,0,75 13,5 For non-standard wall thicknesses, the electric strength shall be at least that of the next smaller standard wall thickness. For wall thicknesses smaller than 0,50 mm, the electric strength shall be at least 20,0 kV/mm. Table 4 Fluid

39、 resistant property requirements for types C and D Property IEC 60684-2 subclause Units Max. or min.Requirements Remarks Resistance to selected fluids Tensile strength Elongation at break 36 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 8 100 Use the fluids and test temperatures specified in Table 5 E

40、N 60684-3-211:2007 8 Table 5 Resistance to selected fluids Fluids Type Standard or symbol Immersion temperature C 2 K Gasoline ISO 1817 Liquid B 40 Fuels Kerosene ISO 1817 Liquid F 40 Silicone base S-1714 *50 Hydraulic fluids Mineral base H-520 * 50 Synthetic base ISO 1817 Liquid 101 100 Mineral bas

41、e ISO 1817 Oil No 2 70 Mineral base O-1176* 70 Oils Mineral base O-142* 50 Isopropyl alcohol 23 Propanol 25 % White spirit 75 % 23 Cleaning fluids Solvents Methylethylketone 23 Runway de-icers Inhibited potassium Acetate 50 % in water 23 De-icing fluids Aircraft de-icers Ethylene glycol 80 % Water 2

42、0 % 23 *These are commercially available fluids which can be identified in Aviation Fluid Guides. Other fluids and/or temperatures may be specified for customers with specific needs. These additional fluids and/or temperatures shall be applicable when incorporated into agreements between the supplie

43、r and customer. _ EN 60684-3-211:2007 9 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appli

44、es. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 2003 Flexible

45、insulating sleeving - Part 1: Definitions and general requirements EN 60684-1 2003 IEC 60684-2 A1 A2 1997 2003 2005 Flexible insulating sleeving - Part 2: Methods of test EN 60684-2 A1 A2 1997 2003 2005 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 ISO 1817 2005 Rubber, vulcanized -

46、Determination of the effect of liquids - - EN 60684-3-211:2007 10 blankBS EN 60684-3-211: 2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at

47、the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and servi

48、ces. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers memb

49、ers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available f