EN 60684-3-240 TO 243-2002 en Flexible insulating sleeving Part 3 Specifications for individual types of sleeving Sheets 240 to 243 Heat-shrinkable PTFE sleeving《绝缘软套管 第3部分 个别型号套管规.pdf

1、BRITISH STANDARD BS EN 60684-3-240 to 243:2002 Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 240 to 243: Heat-shrinkable PTFE sleeving The European Standard EN 60684-3-240 to 243:2002 has the status of a British Standard ICS 29.035.20 BS EN 60684-3-240 t

2、o 243:2002 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 20 December 2002 BSI 20 December 2002 ISBN 0 580 40989 9 National foreword This

3、 British Standard is the official English language version of EN 60684-3-240 to 243:2002. It is identical with IEC 60684-3-240 to 243:2002. It supersedes BS 6893-3-240 to 243:1995 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating mate

4、rial, to Subcommittee GEL/15/3/5, Sleevings, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this docume

5、nt may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or British Standards Online. This publication does not purport to include all the necessary provisions of a contract. User

6、s are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change,

7、 and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date d

8、isplayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-240 to 243 NORME EUROPENNE EUROPISCHE NORM September 2002 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Nor

9、malisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60684-3-240 to 243:2002 E ICS 29.035.20 S

10、upersedes HD 523.3.240 to 243 S1:1993 English version Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 240 to 243: Heat-shrinkable PTFE sleeving (IEC 60684-3-240 to 243:2002) Gaines isolantes souples Partie 3: Spcifications pour types particuliers de gaines

11、 Feuilles 240 243: Gaines thermortractables de PTFE (CEI 60684-3-240 to 243:2002) Isolierschluche Teil 3: Anforderungen fr einzelne Schlauchtypen Bltter 240 bis 243: PTFE- Wrmeschrumpfschluche (IEC 60684-3-240 to 243:2002) This European Standard was approved by CENELEC on 2002-09-01. CENELEC members

12、 are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

13、to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has

14、the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerl

15、and and United Kingdom.Foreword The text of document 15C/1354/FDIS, future edition 2 of IEC 60684-3-240 to 243, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-240 to 243 on 2002-09-01. T

16、his European Standard supersedes HD 523.3.240 to 243 S1:1993. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-06-01 latest date by which the national standards conflictin

17、g with the EN have to be withdrawn (dow) 2005-09-01 Annexes designated “normative“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60684-3-240 to 243:2002 was approved b

18、y CENELEC as a European Standard without any modification. _ Page2 BSEN606843240to243:2002INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part 1: Definitions and general requirement

19、s (IEC 60684-1); Part 2: Methods of test (IEC 60684-2); Part 3: Specifications for individual types of sleeving (IEC 60684-3). This standard gives four of the sheets comprising Part 3 as follows: Sheet 240: Heat-shrinkable PTFE sleeving, low shrink ratio, thick wall Sheet 241: Heat-shrinkable PTFE s

20、leeving, low shrink ratio, medium wall Sheet 242: Heat-shrinkable PTFE sleeving, low shrink ratio, thin wall Sheet 243: Heat-shrinkable PTFE sleeving, high shrink ratio. Page3 BSEN606843240to243:2002FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheets 240 to 24

21、3: Heat-shrinkable PTFE sleeving 1 Scope These sheets of IEC 60684-3 give the requirements for heat-shrinkable (low and high shrink ratio) polytetrafluorethylene (PTFE) sleeving. It is normally available in expanded internal diameter sizes up to 12 mm in three wall thickness ranges as supplied in th

22、e low shrink ratio (sheets 240, 241 and 242) and up to 100 mm in one wall thickness range as supplied in the high shrink ratio (sheet 243). It is normally available in transparent milk white to light tan in colour and the minimum recovery temperature is 350 C. The procedures described in IEC 60216-1

23、 for evaluation of thermal endurance are not readily applicable to PTFE: however, experience of product performance indicates that this sleeving may be suitable for inclusion in systems for operation at temperatures up to 250 C. Sizes other than those specifically listed in this standard may be avai

24、lable as custom items. The items shall be considered to comply with this standard if they comply with the property requirements listed in tables 3 and 4. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specifi

25、c application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

26、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60684-1:1980, Specification for flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Specification for flexible insulating sleev

27、ing Part 2: Methods of test IEC 60216-1:2001, Electrical insulating materials Properties of thermal endurance Part 1: Ageing procedures and evaluation of test results 3 Designation The sleeving shall be identified by the following designation: Page4 BSEN606843240to243:2002Sleeving IEC 60684 3 240 3,

28、0/2,0 Description IEC Publication - Number- Part - Sheet Size (expanded and recovered bore in millimeters) 4 Conditions of test Unless otherwise specified the sleeving shall be shrunk in a forced air circulation oven for (10 1) min at 350 C 5 K before being tested. 5 Requirements In addition to the

29、general requirements given in IEC 60684-1, the sleeving shall comply with the requirements of tables 1, 2, 3 and 4. 6 Sleeving conformance Conformance with the requirements of this specification shall normally be based on the results from size 3,0/2,0 mm for sheets 240, 241 and 242 and size 45/12 mm

30、 for sheet 243. Page5 BSEN606843240to243:2002Table 1 Dimension and mass requirements Sheets 240, 241, 242: low shrink ratio Internal diameter mm Sheet 240 Sheet 241 Sheet 242 Size code Expanded (min.) Recovered (max.) Recovered wall thickness mm Mass per unit length (max.) g/m Recovered wall thickne

31、ss mm Mass per unit length (max.) g/m Recovered wall thickness mm Mass per unit length (max.) g/m 0,8/0,5 0,8 0,5 - 0,23 0,05 1,61 - 0,9/0,6 0,9 0,6 - 0,23 0,05 1,81 - 1,0/0,7 1,0 0,7 0,30 0,05 2,71 0,25 0,05 2,21 - 1,3/0,8 1,3 0,8 0,30 0,05 2,96 0,25 0,05 2,43 0,15 0,05 1,47 1,4/0,9 1,4 0,9 0,40 0,

32、08 4,88 0,25 0,05 2,65 0,15 0,05 1,62 1,5/1,0 1,5 1,0 0,40 0,08 5,23 0,30 0,08 3,86 0,15 0,05 1,77 1,7/1,1 1,7 1,1 0,40 0,08 5,58 0,30 0,08 4,14 0,15 0,05 1,91 2,0/1,3 2,0 1,3 0,40 0,08 6,29 0,30 0,08 4,70 0,15 0,05 2,21 2,4/1,6 2,4 1,6 0,40 0,08 7,35 0,30 0,08 5,54 0,15 0,05 2,65 3,0/2,0 3,0 2,0 0,

33、40 0,08 8,76 0,30 0,08 6,66 0,20 0,05 4,14 4,0/2,4 4,0 2,4 0,40 0,08 10,18 0,30 0,08 7,78 0,20 0,05 4,88 5,0/3,0 5,0 3,0 0,50 0,10 15,90 0,30 0,08 9,45 0,20 0,05 5,98 6,0/3,6 6,0 3,6 0,50 0,10 18,55 0,38 0,10 14,42 0,20 0,05 7,08 7,7/4,5 7,7 4,5 0,50 0,10 22,52 0,38 0,10 17,60 0,25 0,08 11,73 9,4/5,

34、6 9,4 5,6 0,50 0,10 27,38 0,38 0,10 21,48 0,25 0,08 14,40 11/7 11 7 0,50 0,10 33,57 0,38 0,10 26,43 0,25 0,08 17,80 12/8 12 8 0,50 0,10 37,98 0,38 0,10 29,96 0,25 0,08 20,23 Sleeving with a non-standard nominal internal diameter shall have a wall thickness at least as large as the next largest stand

35、ard size. Page6 BSEN606843240to243:2002Table 2 Dimensions and mass requirements Sheet 243: high shrink ratio Internal diameter mm Size code Expanded (min.) Recovered (max.) Recovered wall thickness mm Mass per unit length(max.) g/m 2,0/0,67 2,0 0,67 0,23 0,10 2,43 3,2/1,0 3,2 1,0 0,25 0,10 3,48 6,4/

36、1,6 6,4 1,6 0,30 0,10 5,89 9,5/2,5 9,5 2,5 0,30 0,10 8,54 12,5/3,6 12,5 3,6 0,38 0,10 14,42 16/4,5 16 4,5 0,38 0,10 17,60 19/5,6 19 5,6 0,38 0,10 21,48 25/7,1 25 7,1 0,38 0,10 26,78 32/9 32 9 0,38 0,10 33,49 38/10 38 10 0,38 0,10 37,03 45/12 45 12 0,38 0,10 44,09 50/13 50 13 0,50 0,10 60,06 57/15 57

37、 15 0,50 0,10 68,90 64/17 64 17 0,50 0,10 77,73 70/18 70 18 0,50 0,10 82,15 76/20 76 20 0,50 0,10 90,98 83/22 83 22 0,50 0,10 99,81 95/24 95 24 0,65 0,13 142,27 100/26 100 26 0,65 0,13 153,75 Sleeving with a non-standard nominal internal diameter shall have a wall thickness at least as large as the

38、next largest standard size. Page7 BSEN606843240to243:2002Table 3 Property requirements Property IEC 60684-2 clause or subclause Units Max. or min. Requirements Remarks Dimensions - internal diameter - wall thickness - concentricity Expanded Expanded Recovered 3 3.1.2 3.3.2 3.3.3 mm mm % - Min. Table

39、 1 Table 1 65* 50+ 85 *For sheets 240 to 242 + For sheet 243 Density 4 g/cm 3 Min. 2,13 Heat shock 6 - - There shall be no signs of dripping, cracking or flowing Heat at 400 C 5 K Longitudinal change 9 % Max. 20 Heat the expanded sleeving at 350 C 5 K for (10 2) min Bending at low temperature 14 - -

40、 No cracks shall be visible Condition at 55 C 3 K For strips, the mandrel shall be no more than 10 times the wall thickness. Full section sleeving is tested unfilled and the mandrel shall be no more than 10 times the outer diameter. Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 MP

41、a % Min. Min. 17 250 Use a jaw separation rate of 50 mm/min. Below 6,5 mm diameter as sleeving; at 6,5 mm diameter and above as dumb-bells. Secant modulus at 100 % elongation 19.5 MPa Min. 12 Breakdown voltage 21 kV Min. See table 4 Volume resistivity at room temperature 23 23.4.2 m Min. 10 15 Mass

42、per unit length 38 g/m Max. Table 1 and table 2 Page8 BSEN606843240to243:2002Breakdown voltage shall be determined at room temperature by any of the methods described in 21.2, 21.3, 21.4 of IEC 60684-2. The rate of application of voltage shall be 500 V/s. Table 4 Breakdown voltage Nominal recovered

43、wall thickness mm Minimum breakdown voltage kV 0,15 to 0,20 6,0 0,21 to 0,28 8,0 0,29 to 0,35 10,0 0,36 to 0,40 12,0 0,41 and larger 14,0 Page9 BSEN606843240to243:2002Annex ZA (normative) Normative references to international publications with their corresponding European publications This European

44、Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications appl

45、y to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the releva

46、nt EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 1980 Specification for flexible insulating sleeving Part 1: Definitions and general requirements EN 60684-1 1995 IEC 60684-2 1997 Flexible insulating sleeving Part 2: Methods of test EN 60684-2 1997 IEC 60216-1 2001 Electrical insulatin

47、g materials - Properties of thermal endurance Part 1: Ageing procedures and evaluation of test results EN 60216-1 2001 Page10 BSEN606843240to243:2002BS EN 60684-3-240 to 243:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsib

48、le for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary