EN 60794-3-10-2015 en Optical fibre cables - Part 3-10 Outdoor cables - Family specification for duct directly buried or lashed aerial optical telecommunication cables.pdf

1、BSI Standards PublicationOptical fibre cablesPart 3-10: Outdoor cables Family specification for duct, directly buried orlashed aerial optical telecommunication cablesBS EN 60794-3-10:2015National forewordThis British Standard is the UK implementation of EN 60794-3-10:2015. It isidentical to IEC 6079

2、4-3-10:2015. It supersedes BS EN 60794-3-10:2009 which is withdrawn.The UK participation in its preparation was entrusted by Technical Com-mittee GEL/86, Fibre optics, to Subcommittee GEL/86/1, Optical fibres and cables.A list of organizations represented on this committee can be obtained onrequest

3、to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83520 9ICS 33.180.10Compliance with a British Stan

4、dard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60794-3-10:2015EUROPEAN STANDARD NORME EUROPE

5、NNE EUROPISCHE NORM EN 60794-3-10 February 2015 ICS 33.180.10 Supersedes EN 60794-3-10:2009 English Version Optical fibre cables - Part 3-10: Outdoor cables - Family specification for duct, directly buried or lashed aerial optical telecommunication cables (IEC 60794-3-10:2015) Cbles fibres optiques

6、- Partie 3-10: Cbles extrieurs - Spcification de famille pour les cables optiques de tlcommunication destins tre installs dans des conduites, directement enterrs ou attachs en arien (IEC 60794-3-10:2015) Lichtwellenleiterkabel - Teil 3-10: Auenkabel - Familienspezifikation fr LWL-Fernmeldekabel fr R

7、hren- und direkte Erdverlegung sowie Befestigung an Freileitungen oder Seilen (IEC 60794-3-10:2015) This European Standard was approved by CENELEC on 2015-02-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stan

8、dard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (En

9、glish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees

10、of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloveni

11、a, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rig

12、hts of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60794-3-10:2015 E BS EN 60794-3-10:2015EN 60794-3-10:2015 - 2 - Foreword The text of document 86A/1630/FDIS, future edition 3 of IEC 60794-3-10, prepared by SC 86A “Fibres and cables“ of IEC/TC 86 “F

13、ibre optics“ was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60794-3-10:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-11-12

14、latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-02-12 This document supersedes EN 60794-3-10:2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall

15、not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60794-3-10:2015 was approved by CENELEC as a European Standard without any modification. BS EN 60794-3-10:2015- 3 - EN 60794-3-10:2015 Annex ZA (normative) Normative r

16、eferences to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, th

17、e latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in

18、 this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60793-2 - Optical fibres - Part 2: Product specifications - General EN 60793-2 - IEC 60794-1-1 - Optical fibre cables - Part 1-1: Generic specification - General EN 60794-1-1 - IEC 60794-1-2 - Optical fibre cables -

19、 Part 1-2: Generic specification - Cross reference table for optical cable test procedures EN 60794-1-2 - IEC 60794-1-21 - Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods EN 60794-1-21 - IEC 60794-1-22 2012 Optical fibre cables

20、 - Part 1-22: Generic specification - Basic optical cable test procedures - Environmental test methods EN 60794-1-22 2012 IEC 60794-3 2001 Optical fibre cables - Part 3: Sectional specification - Outdoor cables EN 60794-3 2002 IEC 60811-202 - Electric and optical fibre cables - Test methods for non-

21、metallic materials - Part 202: General tests - Measurement of thickness of non-metallic sheath EN 60811-202 - IEC 60811-203 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 203: General tests - Measurement of overall dimensions EN 60811-203 - IEC 60811-604 - Elect

22、ric and optical fibre cables - Test methods for non-metallic materials - Part 604: Physical tests - Measurement of absence of corrosive components in filling compounds EN 60811-604 - BS EN 60794-3-10:2015 2 IEC 60794-3-10:2015 IEC 2015 CONTENTS 1 Scope 5 2 Normative references 5 3 Terms, definitions

23、, symbols and abbreviations . 5 4 General requirements 6 4.1 Optical fibres 6 4.2 Cable element . 6 4.3 Optical fibre cable construction . 6 5 Details of family requirements and test conditions for optical fibre cable tests . 6 5.1 General . 6 5.2 Tensile performance . 6 Family requirements 6 5.2.1T

24、est conditions 6 5.2.25.3 Crush 7 Family requirements 7 5.3.1Test conditions 7 5.3.25.4 Impact. 7 Family requirements 7 5.4.1Test conditions 7 5.4.25.5 Repeated bending . 7 Family requirements 7 5.5.1Test conditions 7 5.5.25.6 Torsion . 8 Family requirements 8 5.6.1Test conditions 8 5.6.25.7 Bend .

25、8 Family requirements 8 5.7.1Test conditions 8 5.7.25.8 Temperature cycling . 8 Family requirements 8 5.8.1Test conditions 8 5.8.25.9 Water penetration . 9 Family requirements 9 5.9.1Test conditions 9 5.9.25.10 Ageing 9 Family requirements 9 5.10.1Test conditions 9 5.10.2Annex A (normative) Blank de

26、tail specification and minimum requirements 10 A.1 Blank detail specification 10 A.2 Cable construction 12 Bibliography 13 Table A.1 Cable description . 10 Table A.2 Cable construction . 12 BS EN 60794-3-10:2015IEC 60794-3-10:2015 IEC 2015 5 OPTICAL FIBRE CABLES Part 3-10: Outdoor cables Family spec

27、ification for duct, directly buried or lashed aerial optical telecommunication cables 1 Scope This part of IEC 60794, which is a family specification, covers optical telecommunication cables to be used in ducts or direct buried applications. The cable may also be used for lashed aerial applications.

28、 Requirements of the sectional specification IEC 60794-3 for duct, buried and aerial cables are applicable to cables covered by this standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. F

29、or dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60793-2, Optical fibres Part 2: Product specifications General IEC 60794-1-1, Optical fibre cables Part 1-1: Generic specification Genera

30、l IEC 60794-1-2, Optical fibre cables Part 1-2: Generic specification Cross reference table for optical cable test procedures IEC 60794-1-21, Optical fibre cables Part 1-21: Generic specification Basic optical cable test procedures Mechanical test methods1IEC 60794-1-22:2012, Optical fibre cables Pa

31、rt 1-22: Generic specification Basic optical cable test procedures Environmental test methods IEC 60794-3:2001, Optical fibre cables Part 3: Sectional specification Outdoor cables IEC 60811-202, Electric and optical fibre cables Test methods for non-metallic materials Part 202: General tests Measure

32、ment of thickness of non-metallic sheath IEC 60811-203, Electric and optical fibre cables Test methods for non-metallic materials Part 203: General tests Measurement of overall dimensions IEC 60811-604, Electric and optical fibre cables Test methods for non-metallic materials Part 604: Physical test

33、s Measurement of absence of corrosive components in filling compounds 3 Terms, definitions, symbols and abbreviations For the purposes of this document, the terms, definitions, symbols and abbreviations given in IEC 60794-1-1 apply. _ 1To be published. BS EN 60794-3-10:2015 6 IEC 60794-3-10:2015 IEC

34、 2015 4 General requirements 4.1 Optical fibres The optical fibre shall conform to the requirements of IEC 60793-2. The fibre type shall be agreed between the customer and supplier. The cabled fibre shall conform to IEC 60794-3. 4.2 Cable element The cable elements shall conform to IEC 60794-3. 4.3

35、Optical fibre cable construction The cable construction shall conform to IEC 60794-3. 5 Details of family requirements and test conditions for optical fibre cable tests 5.1 General Tests on single-mode fibre cables are typically carried out at 1 550 nm. Multimode fibre cables are typically tested at

36、 1 300 nm. Measurement at other wavelengths or range of wavelengths may be agreed upon between the customer and supplier. 5.2 Tensile performance Family requirements 5.2.1For 1 % proof-tested fibres, the fibre strain under long-term tensile load (TL) shall not exceed 20 % of this fibre proof strain

37、(equal to absolute 0,2 % strain) and there shall be no change in attenuation during the test. Under short-term tensile load (TM) the fibre strain shall not exceed 60 % of the fibre proof strain and the attenuation change during test shall be measured and recorded. Other criteria may be agreed betwee

38、n the customer and the supplier. For fibres proof tested at higher levels the safe long-term load will not scale linearly with proof strain, so a lower percentage of the proof strain is applicable. For greater than 1 % up to 2 % proof-tested fibres, TLshall be limited to 17 % of the proof-test strai

39、n (equal to absolute 0,34 % strain for 2 % proof tested fibres).Under visual examination without magnification, there shall be no damage to the sheath or to the cable elements. Test conditions 5.2.2Method: IEC 60794-1-21, Method E1 Fibre length: Finished cable length Tensile load on cable: Long-term

40、 tensile load (TL) and short-term tensile load (TM), where: TM1 W (direct burial or blowing in duct); TM1,5 W (pulling in duct); Other loads may be applied in accordance with particular user conditions, e.g. 2 700 N TL= 0,3 TMFor aerial cables, the long-term tensile load may be greater than or equal

41、 to the short-term tensile load. Diameter of test pulleys: Typically 1 m but not less than the minimum loaded bending diameter specified for the cable. BS EN 60794-3-10:2015IEC 60794-3-10:2015 IEC 2015 7 5.3 Crush Family requirements 5.3.1Under long-term load there shall be no change in attenuation

42、at 1 550 nm during the test and under short-term load there shall be no change in attenuation at 1 550 nm after the test. The installation load shall not be less than the long-term load. Under visual examination there shall be no damage to the sheath or to the cable elements. The imprint of the plat

43、e or mandrel on the sheath is not considered mechanical damage. Test conditions 5.3.2Method: IEC 60794-1-21, Method E3A The default method is the plate/plate test, Method E3A. Optionally, the mandrel/plate test, Method E3B, may be conducted if requested by the detail specification. Short- and long-t

44、erm tests may be conducted separately. Load (short term): 1,5 kN (un-armoured); 2,2 kN (armoured) Load (long term): 0,75 kN (un-armoured); 1,1 kN (armoured) 5.4 Impact Family requirements 5.4.1Under visual examination without magnification there shall be no damage to the sheath or to the cable eleme

45、nts. The imprint of the striking surface on the sheath is not considered mechanical damage. There shall be no permanent change in attenuation after the test. Test conditions 5.4.2Method: IEC 60794-1-21, Method E4 Number of impacts: One in 3 different places spaced not less than 500 mm apart Impact e

46、nergy: Un-armoured cable: 10 J Armoured cable: 20 J to 30 J, depending on particular user conditions Striking surface curvature radius: 300 mm 5.5 Repeated bending Family requirements 5.5.1Under visual examination without magnification there shall be no damage to the sheath and to the cable elements

47、. Test conditions 5.5.2Method: IEC 60794-1-21, Method E6 Number of cycles: 25 or different number of cycles may be applied in accordance with the particular user conditions Load: Adequate to assure uniform contact with the mandrel Bending radius: 20 d BS EN 60794-3-10:2015 8 IEC 60794-3-10:2015 IEC

48、2015 5.6 Torsion Family requirements 5.6.1Under visual examination without magnification, there shall be no damage to the sheath or to the cable elements. Test conditions 5.6.2Method: IEC 60794-1-21, Method E7 5.7 Bend Family requirements 5.7.1There shall be no permanent change in attenuation after

49、the test. Test conditions 5.7.2Method: IEC 60794-1-21, Method E11 The default method is Method E11A. For large and/or stiff cables (e.g. where the mandrel diameter required is 20 d, IEC 60794-1-21, Method E11B may be used. Diameter of mandrel: 20 d For cable incorporating a non-metallic rod and/or metallic armouring, bending shall be limited to a value from 20 d to 80 d. Number of cycles: 3 Number of turns/helix: 4 Te