EN 60811-510-2012 en Electric and optical fibre cables - Test methods for non-metallic materials - Part 510 Mechanical tests - Methods specific to polyethylene and polypropylene co.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationElectric and optical fibre cables Test methods for non-metallic materialsPart 510: Mechanical tests Methods specific to polyethylene and polypropylene compounds Wrapping test aft

2、er thermal ageing in airBS EN 60811-510:2012National forewordThis British Standard is the UK implementation of EN 60811-510:2012. It isidentical to IEC 60811-510:2012. In the UK, the relationship between the supersessions of BS EN 60811 seriescan be summarized as follows.Superseded standards are wit

3、hdrawnThe UK participation in its preparation was entrusted by Technical CommitteeGEL/20, Electric cables, to Subcommittee GEL/20/17, Electric Cables - Lowvoltage.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to inc

4、lude all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 65334 6ICS 29.035.01; 29.060.20Compliance with a British Standard cannot confer immunity fromlegal obligation

5、s.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 July 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60811-510:2012BS EN 60811-100 together with Supersedes - -201, -202, -203, -501 BS EN 60811-1-1:

6、1995 -301, -302, -411, -601, -602, -603, -604 BS EN 60811-5-1:2000 -401, -412 BS EN 60811-1-2:1995 -402, -502, -503, -606 BS EN 60811-1-3:1995 -403, -404, -507 BS EN 60811-2-1:1998 -405, -409 BS EN 60811-3-2:1995 -406, -511, -605, -607 BS EN 60811-4-1:2004 -407, -408, -410, -510, -512, -513 BS EN 60

7、811-4-2:2004 -504, -505, -506 BS EN 60811-1-4:1995 -508, -509 BS EN 60811-3-1:1995EUROPEAN STANDARD EN 60811-510 NORME EUROPENNE EUROPISCHE NORM June 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotec

8、hnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60811-510:2012 E ICS 29.035.01; 29.060.20 Supersedes EN 60811-4-2:2004 (partially)English version Electric

9、 and optical fibre cables - Test methods for non-metallic materials - Part 510: Mechanical tests - Methods specific to polyethylene and polypropylene compounds - Wrapping test after thermal ageing in air (IEC 60811-510:2012) Cbles lectriques et cbles fibres optiques - Mthodes dessai pour les matriau

10、x non-mtalliques - Partie 510: Essais mcaniques - Mthodes spcifiques pour les mlanges polythylne et polypropylne - Essai denroulement aprs vieillissement thermique dans lair (CEI 60811-510:2012)Kabel, isolierte Leitungen und Glasfaserkabel - Prfverfahren fr nichtmetallene Werkstoffe - Teil 510: Mech

11、anische Prfungen - Verfahren speziell fr Polyethylen- und Polypropylenmischungen - Wickelprfung nach thermischer Alterung in Luft (IEC 60811-510:2012)This European Standard was approved by CENELEC on 2012-04-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stip

12、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This Europ

13、ean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC mem

14、bers are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovak

15、ia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. EN 60811-510:2012 - 2 - Foreword The text of document 20/1306/FDIS, future edition 1 of IEC 60811-510, prepared by IEC/TC 20 “Electric cables“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60811-5

16、10:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-01-17 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2

17、015-04-17 This document supersedes Clause 10 of EN 60811-4-2:2004 (partially). Full details of the replacements are shown in Annex A of EN 60811-100:2012. There are no specific technical changes with respect to EN 60811-4-2:2004, but see the Foreword to EN 60811-100:2012. This standard is to be read

18、 in conjunction with EN 60811-100. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This standard covers the Principle Elements of the

19、Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC). Endorsement notice The text of the International Standard IEC 60811-510:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliograph

20、y, the following note has to be added for the standard indicated : IEC 60811-4-2:2004 NOTE Harmonized as EN 60811-4-2:2004 (not modified). BS EN 60811-510:2012- 3 - EN 60811-510:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publication

21、s The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE

22、When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60811-100 2012 Electric and optical fibre cables - Test methods for non-metallic materials - Part 100: General EN 60811-100 2012 BS EN 60

23、811-510:2012 2 60811-510 IEC:2012 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 4 Test method . 6 4.1 General . 6 4.2 Apparatus 6 4.3 Sampling . 6 4.4 Ageing procedure 7 4.5 Test procedure 7 4.6 Evaluation of results 7 5 Test report 7 Bibliography 8 BS

24、EN 60811-510:201260811-510 IEC:2012 5 INTRODUCTION The IEC 60811 series specifies the test methods to be used for testing non-metallic materials of all types of cables. These test methods are intended to be referenced in standards for cable construction and for cable materials. NOTE 1 Non-metallic m

25、aterials are typically used for insulating, sheathing, bedding, filling or taping within cables. NOTE 2 These test methods are accepted as basic and fundamental and have been developed and used over many years principally for the materials in all energy cables. They have also been widely accepted an

26、d used for other cables, in particular optical fibre cables, communication and control cables and cables for ships and offshore applications. BS EN 60811-510:2012 6 60811-510 IEC:2012 ELECTRIC AND OPTICAL FIBRE CABLES TEST METHODS FOR NON-METALLIC MATERIALS Part 510: Mechanical tests Methods specifi

27、c to polyethylene and polypropylene compounds Wrapping test after thermal ageing in air 1 Scope This Part 510 of IEC 60811 specifies the test method for a wrapping test after thermal ageing in air. This test method applies specifically to polyolefin insulation in communication cables. This test is i

28、ntended for polyolefin insulations of unfilled cables and of dry cores for filled cables, where the insulation has a wall thickness of less than or equal to 0,8 mm. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable

29、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60811-100:2012, Electric and optical fibre cables Test methods for non-metallic materials Part 100: General 3 Terms

30、 and definitions For the purposes of this document, the definitions given in IEC 60811-100 apply. 4 Test method 4.1 General This part of IEC 60811 shall be used in conjunction with IEC 60811-100. All the tests shall be carried out not less than 16 h after the extrusion or cross-linking, if any, of t

31、he compounds used for insulating or sheathing. 4.2 Apparatus The apparatus consists of the following parts: a smooth metal mandrel and loading elements; a winding device, preferably with mechanically driven mandrel; an electrically heated cabinet with natural air flow. 4.3 Sampling The test shall be

32、 carried out on four test pieces for each length of cable or core to be tested. Take a sample 2 m long and cut it into four test pieces of equal length. BS EN 60811-510:201260811-510 IEC:2012 7 Carefully remove the coverings and braidings, if any, from the test pieces and any filling compound which

33、may adhere to the cores. Leave the conductor within the insulation. Then straighten the test pieces. 4.4 Ageing procedure The test pieces prepared in accordance with 4.3 shall be suspended vertically for 14 24 h at (100 2) C in the middle of the heating chamber in accordance with 4.2 so that each te

34、st piece is at least 20 mm from any other test piece. Not more than 2 % of the chamber volume shall be occupied by the test pieces. Immediately after the ageing period, the test pieces shall be taken out of the chamber and left at ambient temperature, without being exposed to direct sunlight, for at

35、 least 16 h. NOTE The ageing time and/or ageing temperature may be increased if required by the relevant cable specifications. 4.5 Test procedure 4.5.1 Test pieces according to 4.3 shall be subjected, after ageing in accordance with 4.4, to a winding test at ambient temperature. 4.5.2 The conductor

36、shall be laid bare at one end. A weight shall be applied to the exposed conductor end, exerting a pull of 15 N/mm2 20 % with respect to the conductor cross-section. Ten windings shall be made on the other end of the test piece by means of a winding device in accordance with 4.2 on a metal mandrel at

37、 a speed of about 1 revolution per 5 s. The winding diameter shall be 1 to 1,5 times the test piece diameter. Subsequently, the test pieces wound on the mandrel shall be removed from the latter and shall be kept in their helical form for 24 h at (70 2) C in the vertical position, substantially in th

38、e middle of the heating chamber in accordance with 4.2. 4.6 Evaluation of results After cooling down to ambient temperature, the test pieces shall show no cracks when examined with normal or corrected vision without magnification. The test may be repeated once more if a test piece fails. 5 Test repo

39、rt The test report shall be in accordance with that given in IEC 60811-100. BS EN 60811-510:2012 8 60811-510 IEC:2012 Bibliography IEC 608011-4-2:2004, Insulating and sheathing materials of electric and optical cables Common test methods Part 4-2: Methods specific to polyethylene and polypropylene c

40、ompounds Tensile strength and elongation at break after conditioning at elevated temperature Wrapping test after conditioning at elevated temperature Wrapping test after thermal ageing in air Measurement of mass increase Long-term stability test Test method for copper-catalyzed oxidative degradation

41、 (withdrawn) _ BS EN 60811-510:2012This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI

42、is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are peri

43、odically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whi

44、le using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an ind

45、ividual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the

46、 BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementat

47、ion of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are ke

48、pt up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications ar