EN 60852-4-1996 en Outline Dimensions of Transformers and Inductors for Use in Telecommunication and Electronic Equipment Part 4 Transformers and Inductors Using YUI-2 Laminations《.pdf

1、BRITISH STANDARD Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment Part 4. Tkansformers and inductors using YUI-2 laminations The European standard EN 608524 : 1996 has the status of a British Standard ICs 29.180 NO COPYING WITHOUT BSI PERMISSION

2、EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 60852-4 : 1997 IEC 852-4 : 1996 BS EN 60862-4 : 1997 Amd. No. Date Committees responsible for this British Standard Text affected The preparation of this British Standard was entrusted to Technical Committee EPL/51, kansfonners, inductors, magnetic componen

3、ts and ferrite materials, upon which the following bodies were represented: Federation of the Electronics Industry Muiistry of Defence National Physical Laboratmy National Supervising Inspectorate - SI PC) This British Standard, having been prepared under the direction of the Electrotechnid Sector B

4、oard, was published under the authority of the Standards Board and comes into effect on 15 April 1997 1 O BSI 1997 The following BSI references relate to the work on this standard Committee reference EPiJ51 Draft for cornent 92/03962 DC ISBN O 680 27199 4 National foreword This Part of BS EN 60852 h

5、as been prepared by Rchnical Committee EPY51, and is the English ianguage veision of EN 608524 : 1996, published by the European Committee for Electrotechnical standardization (CENELEC). It is identid with IEC 8524 : 1996, Ouin diwions of transformers and inductors for use in telecommunkation and eE

6、eccron.ic equipment Part 4. %mfm an 1979 sas BS EN 20286 : IS0 system of limits and fits Part 1: 1993 IS0 system of limits and fits. Bases of bhw, deviations and fits EN 202861 : 1993 Is0 286-1 : 1988 * * VI Compliance with a British Standard does not of itself confer immunity from legal obligations

7、. Summary of pages This document comprises a hnt cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 18, an inside back cover and a back cover. L O BSI 1997 i _ STD-BSI BS EN b52-LI-ENGL 1777 162Libb9 b07377 2$7 EUROPEAN STANDARD EN 60852-4 NORME EUROPEENNE EUROPISCHE NORM Au

8、gust 1996 ICs 29.180 Dascripton: Transformen and induoton. YU-2 Idnrtionr, assembly designation, mounting iwas, stack heights, verticel mounting, levai mounting English version Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment Part 4: Transformers

9、 and inductors using YU(-2 laminations (IEC 852-4: 1996) Dimensions extrieures des transformateurs et inductances destins aux quipements lectroniques et de tlcommunications Partie 4: Transformateurs et dcoupes Y UI-2 Raumbedarfsrnae fr Transformatoren und Drosseln f r nac hrichtentechnisc he und ele

10、ktronische Einrichtungen Teil 4: Transformatoren und Drosseln mit YU1 2-Kernblechen inductances utilisant des t8les (CE1 852-4: 1996) (IEC 852-4: 1996) This European Standard was approved by CENELEC on 1996-07-02. CENELEC members are bound to comply with the CENICENUK: Intemal Regdations which stipu

11、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-todate lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any COUEUX member. This European Standard

12、exists in three officiai versions (English, French, German). A version in any other language made by translation under the responsibility of a CENUK: member into its own language and notified to the Centrai Secretariat has the same status as the official versions. CENELEC members are the national el

13、ectrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greace, Iceland, Ireland, itaiy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation

14、Electrotechnique Europaisches Komitee fr Elektrotechnische Normung Centrd Secretariat: rue de Stassart 35, B - 1060 BNSSS * 1996 Copyright remervd to CENELEC members Ref. NO. EN 60852-41996 E STD-BSI BS EN b0852-Y-ENGL L797 W Lb2Libb7 Ob07378 LO3 W Page 2 EN 60852-4 : 1996 Foreword The text of docum

15、ent 51 /41 GFDIS, future edition 1 of IEC 8524, prepared by IEC TC 51 , Magnetic components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 608524 on 19964742. The following dates were fixed: - latest date by which the EN has to be implemented

16、at national level by publication of an identical national standard or by endorsement (dop) 199744-01 with the,EN have to be withdrawn (dow) 1997-04-01 - latest date by which the national standards conflicting Annexes designated “normative“ are part of the body of the standard. Annexes designated “in

17、formative“ are given for information only. In this standard, annex ZA is normative and annexes A and 6 are informative. Annex ZA has been added by CENELEC. The text of the International Standard IEC 8524:1996 was approved by CENELEC as a European Standard without any modification. STD*BSI BS EN b085

18、2-q-ENGL 1777 = 1b24bb9 Ob07377 OiT Page 3 EN 60852-4 : 1996 CONTENTS clause page 1 2 3 4 5 6 Scope . . . . . Normative references . Laminat ions . . . . . . . . . . . . . . . . . . . . . . . , . . . . . Assembly designation . . General requirements 5.1 Mounting styles 5.2 Stack heights 5.3 Toleranc

19、es Vertical mounting style Level mounting style 7.1 Bracket mounting . 7.2 Pillar mounting 7.3 Printed wiring board mounting 4 4 4 5 5 5 6 7 7 9 9 10 12 Annexes A (informative) Calculation for dimensions of vertical mounting style . . . . . . . B (informative) Calculation for dimensions of level mou

20、nting style . . . . . 15 16 %(normative) Normative references to international publications with their corresponding European publications . 17 , STD-BSI BS EN b0852-LI-ENGL-L777 Lb2Llbb7 b07380 8bL Page 4 EN 60862-4 : 1996 OUTLINE DIMENSIONS OF TRANSFORMERS AND INDUCTORS FOR USE IN TELECOMMUNICATIO

21、N Part 4: Transformers and inductors using YUI-2 laminations AND ELECTRONIC EQUIPMENT - 1 Scope This part of IEC 852 specifies the outline dimensions of transformers and inductors, using YUI-2 laminations as specified below, built for the most commonly used forms of mounting style, namely vertical m

22、ounting and level mounting. The level mounting style is subdivided into bracket mounting, and pillar mounting and printed wiring board mounting variants. I l 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of th

23、is part of IEC 852. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this part of IEC 852 are encouraged to investigate the possibility of applying the most recent editions of the normative documents in

24、dicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 740: 1982, Laminations for transformers and inductors for use in telecommunication and electronic equipment Amendment 1 (1991) IS0 3: 1973, Preferred numbers - Series of preferred numbers IS0 273

25、: 1979, Fasteners - Clearance holes for bolts and screws IS0 286-1: 1988, IS0 system of limits and fits - Part I: Bases of tolerances, deviations and fits IS0 965: IS0 general purpose metric screw threads - Tolerances i 3 Laminations For the purpose of this part of IEC 852, the laminations shall con

26、form to the dimensions of IEC type YUI-range 2 as prescribed in table 17 of IEC 740. STD-BSI BS EN b0852-Ll-ENGL 1997 Lb24bb7 Ob07381 7T8 * * vi Page 6 EN 60862-4 : 1996 4 A!wmbly designation The designation of assemblies represented by this standard shall be as follows: - IEC 852-4 -YU1 2-20d - Q L

27、 Identification of assembly Number of this standard Identlication of lamination and stack height Indication of mounting styie - Q indicates level mounting style - V indicates vertical mounting style I Indication of mounting devices I - B indicates brackets - L indicates pillars M Indication of coil

28、former type - S indicates standard version - SA indicates standard version with air duct - P indicates printed wiring board version I Indication of grid plan version - M indicates a metric grid pian 5 General requirements 5.1 Mounting styies The mounting styles specified below are based upon proven

29、methods of assembly with metric type YUI-2 laminations. The data provided in clauses 6 and 7 give the main dimensions of: - length, width, height (A, B, Cl; - positioning of mounting holes (D, D2, D3); - fixing hole site (G); - fixing screw size (M); - stack height (SI. Dimensions A, B and C include

30、 an allowance for varnishing. Fixing screws shall be IS0 metric screws having screw threads which are metric coarse and of medium fit in accordance with IS0 965. . Associated tapped holes shall comply with a 6H class of fit in accordance with IS0 965. Page 6 EN 60862-4 : 1996 f B Fixing holes are cl

31、earance holes having diameters taken from the medium series of IS0 273, and screws of corresponding size shall be used for mounting. 1,60 2.00 - Whereslotted fixing holes are used, their width shall equal the stated value of G, and their length shall not exceed 1,8 G. All the listed dimensions in th

32、is standard are in millimetres. 5.2 Stack heights A range of stack heights is specified, which allows continuous variations of power rating, although the square stack is preferred. The increment of stack height follows the R 10 series of preferred numbers, as defined in IS0 3, as a multiple of the w

33、idth of the limbs of the lamination. A suffix letter is used to designate the appropriate stack size as shown in table 1. Table 1 - Multiple of limb width I I 1 Suffix letter I I Multiple of limb width of lamination C d e 0.80 1 .O0 (square stack) 1.25 The lamination designation followed by the appr

34、opriate suffix letter is used the core. o designate If stack heights other than the preferred square stack are used, these shall follow the figures given in table 2, showing the stack heights Snom using the multiple of limb width as shown in table 1. * m * Page 7 EN 60862-4 : 1996 Table 2 - Stack he

35、ight I Stack height S, for suffix letter Designation I I alblcldlelfla 5.3 Tolerances The stack height is shown as nominal and is open to small variations which can be compensated by slotted holes in the fixing brackets. The dimensions, except where indicated as maximum or nominal, shall have tolera

36、nces in accordance with the requirements of IS0 286-1. NOTE - The appropriate tolerance is shown at the head of each column of dimensions in the foilowifig tables. 6 Vertical mounting style The dimensions for the vertical mounting style shall be as given in table 3, corresponding to the cores using

37、square stacks assembled from laminations YU1 2-20d to YU1 2-80d, in accordance with the outline drawing of figure 1. If stack heights other than the preferred square stack are used, these shall follow the R 10 series given in table 1. In this case the appropriate dimensions are obtained by increasin

38、g or decreasing the values by the same amount as the stack height S is changed. STD-BSI BSEN bOB5Z-Y-ENGL L7pm Lb2gbb7 b07384 407 m YU1 2-60d-VS YU1 2-70d-VS YU1 2-8Od-VS Page 8 EN 60862-4 : 1996 412.0 331.0 1520 388,O 112,O 10,O M8 60,O 480,O 387,s 180,O 450,O 130.0 12,O M10 70.0 552,O 444,O 212,O

39、516,O 152,O 14,5 M12 80.0 -:t I+ +I I A I 7- Mounting hdes -Tos s, I- Figure 1 -Vertical mounting style for transformers and Inductors using YUI-4 laminatlons (col1 former standard version and standard version with air duct) Table 3 - Dimensions for transformers and inductors using YUI-2 laminations

40、, vertical mounting style-square stack, coil former standard version and standard version with air duct Assembly 0, 03 G designation A, m, cnux 1) ASB-IEC 852-4 flT12 fIT12 JS14 YU1 2-20d-VS 148,O 118.0 68.0 136,O 48.0 4.8 YU1 2-38d-VS 1 267.0 YU1 2-44d-VS I 316.0 YU1 2-50d-VS I 352.0 177,O 99.0 201

41、,o 69.0 7.0 199.0 103.0 225.0 73.0 7,O 221,O 107,O 249.0 77,O 7,o 258,O 136,O 292,O 96,O 10.0 278.5 142.0 328.0 102,O 10.0 44,O 50.0 I YUI 2-56d-VS I 388,O I 310.0 I 148,O T 364,O 7 108.0 I 10,O I M8 I 56.0 I , Page 9 EN 60852-4 : 1996 7 Levei mounting style The dimensions for the level mounting sty

42、le shall be as given in tables 4, 5 and 61 corresponding to cores using square stacks assembled from laminations YU1 2-1Od to YU1 2-0d, in accordance with the outline drawings of figures 2, 3 and 4, respectively, according to whether the bracket, pillar or printed wiring board mounting version is re

43、quired. If stack heights other than the preferred square stack are used, these shall follow the R 10 series given in table 1. In this case the appropriate dimensions are obtained by increasing or decreasing the values by the same amount as the stack height S is changed. 7.1 Bracket mounting Figure 2

44、 - Level mounting style for transformers and inductors using YUI-2 laminations, bracket mounting (coil former standard version and standard version with air duct) STD.BSI BS EN b52-q-ENGL 1777 W 1b24bb9 Ob073b 28T Assembly 2) Dl D2“ G designation . A, B, 1) cmx Unm ASB-IEC 852-4 w/o I w IlTl 2 *IT1

45、2 JS14 Page10 EN 60852-4 : 1996 Snm Table 4 - Dimensions for transformers and inductors using . YU-2 laminations, level mounting style - bracket mounting - square stack, coli former standard version and standard version with alr duct YU1 2-56d-QBS 360,O 296,O 140.0 160.0 328.0 224.0 10,O YU1 2-6Od-Q

46、BS 380,O 316,O 150.0 170,O 348.0 240,O 10,O YU1 2-7Od-QBS 450.0 370,O 175,O 195,O 410.0 280,O 12,O YU1 2-80d-QBS 520,O 424.0 200.0 220.0 472,O 320.0 143 M8 56,O M8 60.0 M10 70.0 M12 80.0 1 Air gaps of inductors disregarded. 2, wlo: without air duct; w: with air duct. C is overall height including a

47、mounting assembly. 7.2 Pillar mounting Mounting pillars shall be dimensioned so that they do not affect the overall height C. NOTE - The pillars may be supplied either tapped or drilled with suitable clearance holes, corresponding to the metric screw whose size is given in table 5. Where the pillars

48、 are drilled with clearance holes, for dimensions refer to column G instead of column M. Page 11 EN 60852-4 : 1996 YU1 2-2Od-QLS YU1 2-25d-QLS YU1 2-30diQLS YU1 2-34d-QLS 1 I 124.0 108.0 6.0 - 80.0 80,O 48 M4 20,o 154,O 133,O 62,5 - 100,o 100,o 4,s M4 25.0 186.0 162,O 75.0 120.0 120,o 790 M6 30.0 21

49、0,O 182.0 85.0 - 136.0 136.0 7.0 M6 34.0 Figure 3 - Level mounting sty. .Jr transformers and inductors using YUI-2 laminations, pillar mounting (toil former standard version and standard version with air duct) YUI 2-5Od-QLS YU1 2-56d-QLS YUI2-60d-QLS YU1 2-70d-QLS Table 6 - Dimensions for transformers and Inductors using YUI-2 laminations, levei mounting styie - pillar mounting - square stack, coil former standard version and standard version with air duct - - 308.0 266,