EN 60917-2-4-2010 en Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4 Sectional specification - Interface coordination dimen.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationModular order for the development of mechanical structures for electronic equipment practicesPart 2-4: Sectional specification Interface coordination dimensions for the 25 mm equ

2、ipment practice Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in)BS EN 60917-2-4:2010National forewordThis British Standard is the UK implementation of EN 60917-2-4:2010. It isidentical to IEC 60917-2-4:2010.The UK participation

3、in its preparation was entrusted to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessa

4、ry provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 64419 1ICS 31.240Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee

5、 on 31 May 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60917-2-4:2010EUROPEAN STANDARD EN 60917-2-4 NORME EUROPENNE EUROPISCHE NORM April 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique

6、Europisches Komitee fr Elektrotechnische Normung Central Secretariat: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60917-2-4:2010 E ICS 31.240 English version Modular order for the devel

7、opment of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in) (IEC

8、60917-2-4:2010) Ordre modulaire pour le dveloppement des structures mcaniques pour les infrastructures lectroniques - Partie 2-4: Spcification intermdiaire - Dimensions de coordination pour les interfaces des infrastructures au pas de 25 mm - Dimensions dadaptation des bacs ou des chssis, applicable

9、s dans les baies ou les btis, conformment la CEI 60297-3-100 (19 pouces) (CEI 60917-2-4:2010) Modulordnung fr die Entwicklung von Bauweisen fr elektronische Einrichtungen - Teil 2-4: Strukturnorm - Schnittstellen-Koordinationsmae fr die 25-mm-Bauweise - Adaptionsmae fr Baugruppentrger oder Einschbe,

10、 anwendbar in Schrnken oder Gestellen nach IEC 60297-3-100 (19-Zoll) (IEC 60917-2-4:2010) This European Standard was approved by CENELEC on 2010-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s

11、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, Germa

12、n). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria,

13、 Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60917-2-4

14、:2010EN 60917-2-4:2010 - 2 - Foreword The text of document 48D/420/FDIS, future edition 1 of IEC 60917-2-4, prepared by SC 48D, Mechanical structures for electronic equipment, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENE

15、LEC parallel vote and was approved by CENELEC as EN 60917-2-4 on 2010-04-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The followin

16、g dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-04-01 Annex ZA has been adde

17、d by CENELEC. _ Endorsement notice The text of the International Standard IEC 60917-2-4:2010 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60297-3-101 NOTE Harm

18、onized as EN 60297-3-101. IEC 60917-1 NOTE Harmonized as EN 60917-1. IEC 60917-2-1 NOTE Harmonized as EN 60917-2-1. IEC 61587-1 NOTE Harmonized as EN 61587-1. IEC 61587-2 NOTE Harmonized as EN 61587-2. IEC 61587-3 NOTE Harmonized as EN 61587-3. _ BS EN 60917-2-4:2010- 3 - EN 60917-2-4:2010 Annex ZA

19、(normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

20、 the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60297 Series Mechanical structures for electronic equipment - Dimension

21、s of mechanical structures of the 482,6 mm (19 in) series EN 60297 Series IEC 60297-3-100 - Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets EN 602

22、97-3-100 - IEC 60297-3-106 - Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 EN 60297-3-106 - IEC

23、 60917 Series Modular order for the development of mechanical structures for electronic equipment practices EN 60917 Series IEC 60917-2-2 - Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimens

24、ions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units EN 60917-2-2 - BS EN 60917-2-4:2010 2 60917-2-4 IEC:2010 CONTENTS INTRODUCTION.5 1 Scope and object6 2 Normative references .6 3 Arrangement overview

25、 (Figure 1) and definitions 7 4 Dimensions for adaptor flanges of the specific metric subracks or chassis (suitable only where WS1= 425 mm) mountable into 19 in cabinets or racks.8 4.1 General .8 4.2 Dimensions for mounting holes arrangements on the adaptor flanges, mounting layout referred to the b

26、ottom pitch lines of the metric subracks or chassis8 4.3 Dimensions for mounting holes arrangements on the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks or chassis10 Bibliography14 Figure 1 Arrangement overview Adaptation of specific subracks (aperture wid

27、th for plug-in units: WS1= 425 mm, 85 5,0 mm) of IEC 60917-2-4 into cabinets of IEC 60297-3-100 7 Figure 2 Mounting hole arrangements of the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis.8 Figure 3 Dimensions of mounting hole positions of the a

28、daptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis 9 Figure 4 Mounting hole arrangements on the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks or chassis .11 Figure 5 Dimensions of mounting holes positions o

29、f the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks or chassis.12 Table 1 Dimensions of mounting holes positions of the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis 10 Table 2 Dimensions of mounting

30、holes positions of the adaptor flange, mounting layout referred to the unit centre lines of the metric subracks or chassis.13 BS EN 60917-2-4:201060917-2-4 IEC:2010 5 INTRODUCTION The IEC 60917 series of standards provides definitions of mechanical structure and dimensions for metric cabinets, racks

31、, subracks, chassis and plug-in units based on metric modular ordered dimensions. The later developed IEC 60917 series of standards, compared to IEC 60297, provides more logical design practices based on metric dimensioning. The IEC 60297 series of standards also define structures and interface dime

32、nsions for 19 in cabinets, racks and their compatible subracks and chassis. Because of the longer history of the IEC 60297 series of standards and their applications, the combination of 19 in based cabinets, racks, subracks and chassis are broadly applied for all industrial electronic fields in the

33、world. Requests for combined applications with both mechanical structures, the IEC 60917 series (metric standard) and the IEC 60297 series (19 in standard), resulted in requirements to mount metric subracks or chassis into 19 in standard cabinets or racks and, vice versa, 19 in subracks or chassis i

34、nto metric cabinets or racks. To cope with the requirements and needs, it is required to develop definitions for appropriate adaptation dimensions of flanges for metric or 19 in subracks or chassis to mount them into cabinets or racks in accordance with 19 in or metric standard. And the definitions

35、of adaptation dimensions bring economical solutions for installations of electronic equipment into existing cabinets or racks. Further, they provide guidance to electro-mechanical designers to develop systems suitable to be mounted into both IEC standard series flexibly. To meet such market needs, t

36、his standard defines adaptation dimensions for metric subracks or chassis applicable for 19 in cabinets or racks. (Dimensions for the applications, where 19 in subracks or chassis are mounted on metric cabinets or racks, are defined in a separate standard, i.e. IEC 60297-3-106.) BS EN 60917-2-4:2010

37、 6 60917-2-4 IEC:2010 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES Part 2-4: Sectional specification Interface co-ordination dimensions for the 25 mm equipment practice Adaptation dimensions for subracks or chassis applicable in cabinets or racks in a

38、ccordance with IEC 60297-3-100 (19 in) 1 Scope and object This part of IEC 60917 specifies dimensions for mounting flanges of metric subracks or chassis that are to be mounted into 19 in cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60917 series, and for 1

39、9 in cabinets or racks to the IEC 60297 series. EMC, seismic climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that shall be used. The terminology used c

40、omplies with IEC 60917-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

41、IEC 60297 (all parts), Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series IEC 60297-3-100, Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19in) series Part 3-100: Basic dimensions of f

42、ront panels, subracks, chassis, racks and cabinets IEC 60297-3-106, Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 3-106: Adaptation dimensions for subracks and chassis applicable to metric cabinets or racks in accordance with I

43、EC 60917-2-1 IEC 60917 (all parts), Modular order for the development of mechanical structures for electronic equipment practice IEC 60917-2-2, Modular order for the development of mechanical structures for electronic equipment practices Part 2: Sectional specification Interface co-ordination dimens

44、ions for the 25 mm equipment practice Section 2: Detail specification Dimensions for subracks, chassis, backplanes, front panels and plug-in units BS EN 60917-2-4:201060917-2-4 IEC:2010 7 3 Arrangement overview (Figure 1) and definitions This standard defines dimensions for adaptor flanges suitable

45、for metric subracks or chassis (aperture width for plug-in units: WS1= 425 mm, 85 5,0 mm) that are applicable for mounting into 19 in cabinets or racks. Dimensions for applications where 19 in subracks or chassis are to be mounted into metric cabinets or racks are defined in a separate standard (IEC

46、 60297-3-106). All other dimensions are in compliance with the IEC 60917 series (metric standard) and IEC 60297 series (19 in standard). Cabinet in accrodance with IEC 60297-3-100 (19 in) Subrack in accrodance with IEC 60917-2-2 (metric) First pitch line Adaptor flange with 19 in hole-spacing as an

47、interface between the metric subracks or chassis and the 19 in cabinets or racks Support rail Pitchlinen 44,45 85 5,0 449 465,1 Pitch lineinacxcordance with IEC60297-3-100 n 25465,1 1,5 IEC 458/10 Dimensions in mm Figure 1 Arrangement overview Adaptation of specific subracks (aperture width for plug

48、-in units: WS1= 425 mm, 85 5,0 mm) of IEC 60917-2-4 into cabinets of IEC 60297-3-100 BS EN 60917-2-4:2010 8 60917-2-4 IEC:2010 4 Dimensions for adaptor flanges of the specific metric subracks or chassis (suitable only where WS1= 425 mm) mountable into 19 in cabinets or racks 4.1 General Dimensions f

49、or mounting holes arrangements on the flanges are arranged by the two mounting layouts in the cabinets: a) Mounting layout referred to the pitch lines of the metric subracks or chassis, and b) Mounting layout referred to the unit centre lines of the metric subracks or chassis. 4.2 Dimensions for mounting holes arrangements on the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis